NAPCO GEMINI GEM-P1632 Programming Instructions Manual page 16

Page 16
22
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
24
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
3
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
25
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
3
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
26
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
8
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
DATA ENTRY CS RECEIVER 1 FORMAT
blank(•) Ademco Slow, Silent Knight Slow
1 Sescoa, Vertex, DCI, Franklin Fast
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
8 Radionics BFSK
27
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
spaces in between; leave blank (•) any trailing boxes. If an "Ambush Prefix" (Address 0495) is entered, do not program the first two
digits of ANY User Code as the same digits entered for the "Ambush Prefix".
If the programmed code is less than 6 digits, press
Refer to the tables on the next page for the available User Option data entries.
X
GEM-P1632 Programming Instructions
Number of Keypads
Directly enter the total number of Keypads to be installed. Valid entries are from 01 to 07.
Directly enter the number of keypads, including leading zeros. Use number buttons
through . NOTE: Press
9
to proceed.
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including prefix letters, if
necessary, for receiver 1.
for a zero and
G 0
NOTE: Pre-Dial Delay = "D"; Dial-Tone Detection = "E". Pressing
U
space (•). Press to save. Press the NEXT/YES button to proceed. NOTE: Central Station
Receiver 2 and 3 Telephone Numbers can only be entered in Direct Address Programming. See
CS Receiver Options.
Central Station Receiver 1 Account Number
Enter an account number of up to four digits. Use number buttons
digits 1–9. NOTE: Press the
U
blank space (•). Press
Station Receiver 2 and 3 Account Numbers can only be entered in Direct Address Programming.
See CS Reporting Options.
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number buttons
through . NOTE: Press the
9
space (•). Press
G 1
save. Press the NEXT/YES button to proceed.
DATA ENTRY
9
0
B
C
D
E
Enter User Codes (Press the (
Enter up to 32 User Codes with User Options for each code. Refer to the tables below for available
data entries for User Options.
Press once to set cursor to the User Number and enter the desired User Number. Press
R
once again to set the cursor to the User Code. Use the number buttons
R
to enter a code from 3 to 6 digits. Enter up to 6 digits (4 digits are recommended) in the first six boxes
from left to right for each user code. Valid entries are: 0-9. Note: Press
R
for a zero. Press
0
Use number buttons
1
through
G 1 G 5
button for a zero and press the
0
to save. Press the NEXT/YES button to proceed. NOTE: Central
button for a zero and press
0
through
G 4
CS RECEIVER 1 FORMAT
FBI 4/3/1
Radionics Modem 2
SIA
Ademco Point ID
Ademco Express
Pager
) button to set cursor)
R
to set the cursor to USER OPTIONS.
WI1148B 10/06
U
to save. Press the NEXT/YES button
through for digits 1–9; press
9
for letters B–F, respectively.
will produce a blank
0
through
1
G 0
G 0
for letters B–E, respectively. Press
NOTE: Modem
available only
Address Programming.
Central Station Receiver 2
and 3 Formats can only be
entered in Direct Address
Programming.
Receiver Options.
1
for a zero. No blank
0
L
NAPCO Security Systems
1
for
9
buttons for a
1
for a blank
U
to
IIe is
in Direct
See CS
through
9