Optimum OPTidrill DH 24BV Operating Manual page 4

1.10 Safety check ...........................................................................................................................................74
1.11 EMERGENCY-STOP push button..........................................................................................................74
1.11.1 Main switch ...............................................................................................................................74
1.12 Drilling table ............................................................................................................................................75
1.13 Drill chuck protection ..............................................................................................................................75
1.14 Personal protective equipment ...............................................................................................................75
1.15 Safety during operation...........................................................................................................................76
1.16 Safety during maintenance .....................................................................................................................76
1.17 Disconnecting and securing the drilling machine....................................................................................76
1.18 Mechanical maintenance work ...............................................................................................................76
1.19 Accident report........................................................................................................................................77
1.20 Electrical system.....................................................................................................................................77
1.21 Inspection deadlines ...............................................................................................................................77
2 Technical data
2.1 Electrical connection...............................................................................................................................78
2.2 Power drive motor...................................................................................................................................78
2.3 Drilling capacity in steel ..........................................................................................................................78
2.4 Spindle seat ............................................................................................................................................78
2.5 T-slots - size ...........................................................................................................................................78
2.6 Table size ...............................................................................................................................................78
2.7 Spindle stroke .........................................................................................................................................78
2.8 Throat depth ...........................................................................................................................................78
2.9 Machine height .......................................................................................................................................78
2.10 Column diameter ....................................................................................................................................78
2.11 Distance spindle - table ..........................................................................................................................79
2.12 Dimensions machine foot .......................................................................................................................79
2.12.1 Working surface machine foot...................................................................................................79
2.13 Weight of machine [kg] ...........................................................................................................................79
2.14 Spindle speeds (Motor + Gear) ~ 50 Hz .................................................................................................79
2.15 Spindle speeds (Motor + Gear) ~ 60 Hz .................................................................................................79
2.16 Environmental conditions temperature ...................................................................................................79
2.16.1 Dimensions DH24BV ................................................................................................................81
2.16.2 Dimension DH28BV ..................................................................................................................82
2.17 Dimensions DH34BV ..............................................................................................................................83
2.18 Dimensions DH40BV ..............................................................................................................................84
2.18.1 Dimensions drilling table DH34BV ǀ DH40BV ...........................................................................85
3 Delivery, interdepartmental transport, assembly and commissioning
3.1 Notes on transport, installation, commissioning .....................................................................................86
3.1.1 General risks during internal transport ......................................................................................86
3.2 Transportation to the installation site ......................................................................................................87
3.3 Installation and assembly .......................................................................................................................87
3.3.1 Requirements regarding the installation site .............................................................................87
3.3.2 Assembly...................................................................................................................................87
3.4 Installation...............................................................................................................................................88
3.5 Fixing ......................................................................................................................................................88
3.6 Fixture DH24BV......................................................................................................................................88
3.7 Fixture DH28BV......................................................................................................................................89
3.8 Fixture DH34BV......................................................................................................................................89
3.9 Fixture DH40BV......................................................................................................................................90
3.10 First commissioning ................................................................................................................................90
3.10.1 Power supply.............................................................................................................................90
3.10.2 Warming up the machine ..........................................................................................................91
4 Operation
4.1 Safety......................................................................................................................................................92
4.2 Cooling....................................................................................................................................................92
4.3 Before starting work................................................................................................................................92
4.4 During work.............................................................................................................................................93
4.5 Operation DH24BV .................................................................................................................................94
4.5.1 Control and indicating elements................................................................................................94
4.5.2 Speed change ...........................................................................................................................95
4.5.3 Drilling .......................................................................................................................................95
4.5.4 Releasing the tool from the spindle seat ...................................................................................96
4.6 Operation DH28BV .................................................................................................................................97
4.6.1 Control and indicating elements................................................................................................97
4.6.2 Speed change ...........................................................................................................................98
4.6.3 Drilling .......................................................................................................................................98
4.7 Releasing the tool from the spindle seat.................................................................................................98
4.7.1 With drill drift .............................................................................................................................98
4.7.2 With integrated drill drift ............................................................................................................99
DE | EN
DH24BV | DH28BV | DH34BV | DH40BV
4 Originalbetriebsanleitung Version 1.1.4 - 2022-09-14