Beretta POWER MAX BOX 130-2 P Installation Manual page 63

Heating programming
Group 1
" "
Program Comfort Period
"
Comfort Setpoint
" "
ECO Setpoint
" "
Out of interval setpoint
" "
It supports adjusting the time programme for the CH zones with the
following parameters:
Period setting
Enables the user to select a period from 1 to 7. Period settings enable
the user to adjust the active periods for this zone.
- Active days : Selection of the day (s) on which the period is
active. Enables the user to disable the period set for one or
more days. When this parameter is set as inactive, the oth-
er items on this menu are no longer used and hidden from
the view. The choice of active days is between the following
macro-groups: Sat-Sun, Mon-Fri, Mon-Sun, or individual days:
Mon, Tue, Wed,...
- Interval 1 (hidden if Active Days is disabled) : This parameter
allows the user to regulate the starting and end time of the pe-
riod. The starting time must always be before the finishing time.
- Interval 2 (hidden if Active Days is disabled) : Same as inter-
val 1. Interval added for the activated period.
- Interval 3 (hidden if Active Days is disabled) : Same as inter-
val 1. Interval added for the activated period.
External Zone Group 1 CH - Period
" " "
" "
Active Day(s) Program Comfort Period Sunday
"
" " "
Comfort Setpoint I nterval 1 00:00
" " " "
ECO Setpoint Interval 2 00:00
" " " "
Out of interval setpoint Interval 3 00:00
" " " "
Comfort Set-point
Comfort temperature to be used when the zone is in a certain period.
(10 -30 °C).
ECO set-point
ECO temperature. Adjustable temperature that can be used outside
set periods (5 – 20 °C).
Set-points outside the interval
Selection of the type of set-point to be used when a zone is not on a
set period by selecting between:
- Off
- Comfort
- Eco
- Anti-Freeze (is activated below 5°C NON-ADJUSTABLE)
- Reduced (Calculated as -10°C Comfort Set-point value)
1
"
28.0 °C
" "
20.0 °C
" "
Reduced
" "
1
"
71
"
"
28.0 00:00 °C
" "
00:00 20.0 °C
" "
Reduced 00:00
" "
DHW setting
Group 1
" "
Program Comfort Period
"
Out of interval setpoint
" "
It supports adjusting the time programme for the DHW zone.
Period setting
Enables the user to select a period from 1 to 7. Period settings enable
the user to adjust the active periods for this zone.
- Active days : Selection of the day (s) on which the period is
active. Enables the user to disable the period set for one or
more days. When this parameter is set as inactive, the oth-
er items on this menu are no longer used and hidden from
the view. The choice of active days is between the following
macro-groups: Sat-Sun, Mon-Fri, Mon-Sun, or individual days:
Mon, Tue, Wed,...
- Interval 1 (hidden if Active Days is disabled) : This parameter
allows the user to regulate the starting and end time of the pe-
riod. The starting time must always be before the finishing time.
- Interval 2 (hidden if Active Days is disabled) : Same as inter-
val 1. Interval added for the activated period.
- Interval 3 (hidden if Active Days is disabled) : Same as inter-
val 1. Interval added for the activated period.
External Zone DHW - Period
Group DHW
" " " " "
Program Comfort Period
Active Day(s) Sunday
" " " "
I nterval 1 Comfort Setpoint 00:00
" " " "
Interval 2 ECO Setpoint 00:00
" " " "
Interval 3 Out of interval setpoint 00:00
" " " "
Set-points outside the interval
Selection of the type of set-point to be used when a zone is not on a
set period by selecting between:
- Off
- On
1
"
On
" "
1
"
71
" "
00:00 28.0 °C
" "
20.0 00:00 °C
" "
Reduced 00:00
" "
63