Shaver HD-8-S Operator's & Parts Manual page 20

2. Install the hydraulic valve (item 2) on Valve
Bracket (item 2) using three (3) 5/16-18 x 2-
1/2" valve mounting bolts, washers, and nuts.
NOTE: Do not over-tighten the hardware,
which can warp valve body.
3. Attach the valve and mounting bracket to the
Driver Base Plate using base plate mounting
hardware in the right rear side of the plate.
4. Screw in hydraulic fittings (items 7, 8, & 9) as
shown above. The
3/4FNPT Adapter
working port on top of the valve. The 90°
SAE#12MORB-1/2FNPS Adapter (item 8)
goes into the 'IN' pressure port on the side of
the valve. The 90° SAE#12MORB-3/4FNPT
Adapter (item 9) goes into the 'OUT' side
return port on the valve.
5. Then screw in hydraulic fittings for the Tilt
Cylinders (items 10 & 11) as shown above.
Four (4) straight SAE#10MORB-#6FORB
Adapters (item 10) go into the 'C', 'D', 'E' &
'F' working ports on top of the valve. Then
four (4) 45°
Adapters (item 11) go into the straight
adapters in 'C', 'D', 'E' & 'F' working ports on
top of the valve.
5
6a
Driver hydraulic hoses.
6. Attach the hoses as follows (see above).
Screw in one end of the 3/4" x 48" hose (item
5) into the port on the driver cylinder using
paste-type thread sealant on the fitting. The
four (4) 1/4 x 26" hoses (items 6a, b, c, & d)
connect to the four (4) ports on the tilt
cylinders using paste-type thread sealant on
the fittings.
45° SAE#10MORB-
(Item 7) goes into 'B'
SAE#6MORB-1/4FNPS
6c
6d
6b
Triple Lever Control Valve for Hydraulic Base Plate Parts List
Item Qty. Part No.
SM-003-PVBP
1 1
1
2 VP-03-SP
1
3 SM-0234-P
1
4 SM-025-R
1
5 SM-0252-R
4
6 SM-02111-P
1
7 F-6902-10-12
1
8 CTP-69011208
1
9 SC-50-H52
4
10 F-6410-10-06
4
11 F-6902R-6-4-.03
5
3
6b
6a
Hydraulic Tilt Base Control Valve hoses.
Hydraulic Hose Chart
Valve Port
Item
IN
3
4 OUT
5 B
6a D
6b C
6c F
6d E
7. Attach the other ends of the hoses as follows
(see above). Screw in one end of the 3/4 x 48"
hose (item 5) to the 45° fitting in the 'A'
working port on top of the valve using paste-
type thread sealant on the fittings. The 1/2 x
120 hose (item 3) connects to the 90° fitting in
the 'IN' pressure port on the side of the valve
using paste-type thread sealant on the fittings
and the other end is hooked up to the pressure
hydraulic line from tractor. The 3/4" x 120
20
Description
Plate, Valve Bracket VP-03
Valve – 3 Spool
Hose Assy., 1/2 x 120
Hose Assy., 3/4 x 120
Hose Assy., 3/4 x 48
Hose Assy., 1/4 x 26
Adapter, 45° SAE#10MORB-3/4FNPT
Adapter, 90° SAE#12MORB-1/2FNPS
Adapter, 90° SAE#12MORB-3/4FNPT
Adapter, Str. SAE#10MORB-#6FORB
Adapter, 45° SAE#6MORB-1/4FNPS
4
6d
6c
Location
Pressure Hose
Return Hose
Driver Cylinder
Forward Tilt Cylinder Rod End
Forward Tilt Cylinder Base End
Side Tilt Cylinder Rod End
Side Tilt Cylinder Base End