Related Manuals for Shaver SC-30H
Summary of Contents for Shaver SC-30H
- Page 1 Operation and Parts Manual Hydraulic Safety Stump Busters Operation Maintenance Models: Repair SC-30H Troubleshooting Parts...
-
Page 3: Table Of Contents
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Model SC-30H......12 Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 4: Introduction
Introduction The Shaver Manufacturing Company would like to Product Information congratulate you on your purchase of the Shaver Stumpbuster . You have selected the best Stump The SC-30H Hydraulic Stumpbuster is shipped in Buster in its class. The clean design and uncomplicated... -
Page 5: Safety
. CAUTION Shaver Manufacturing Company cannot anticipate every Indicates a potentially hazardous situation which, if possible circumstance that might involve a potential not avoided, may result in minor or moderate injury . -
Page 6: Safety Instructions
. Do not allow underground cables, pipelines, overhead wires, anyone to operate this equipment without proper and other hazards in the digging area . instructions . Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 7: Operation
Lubrication Information section . Keep hands, feet, hair, and clothing away from ON SC-30H make sure the skid loader bracket is the equipment while the engine is running . secured by the locking levers in the down position . -
Page 8: Operation (Continued)
Specifications block securely . Turn the engine off and remove the key . On SC-30H, disconnect the two hydraulic hoses from the skid loader . SC-30H HYDRAULIC STUMPBUSTER Description Specification Before servicing, make sure the unit is properly attached to the tractor . -
Page 9: Safety Signs And Informational Labels
1 . Keep safety or instructional signs clean and legible at all times . 2 . Replace any missing or hard-to-read safety or instructional signs . 3 . Locations for the signs and replacement part numbers are shown in this section . Shaver Manufacturing Company www.shavermfg.com 712-859-3293... - Page 10 Danger, Read The Manual Decal — Serial Number Plate — 1. 1. MS-161B – Shaver Decal (small) 1. 4. MS-503 – Danger Flying Debris Decal 1. 2. MS-171 – High-Pressure Warning Decal 1. 3. MS-280 – FEMA Member Decal Shaver Manufacturing Company...
- Page 11 8. MS-811 – Call to Dig Decal 6. MS-508-A – Hydraulic Flow Warning Decal 9. MS-2550-H – Clean Quick Couplers Decal 7. MS-514 – Grind Direction Decal 10. PHDC4 – Danger, Read the Manual Decal Shaver Manufacturing Company www.shavermfg.com 712-859-3293...
-
Page 12: Attachment
Attachment 1. Attach the stumpbuster to the skid loader with the Attaching SC-30H Hydraulic Stumpbuster to quick attach bracket by mounting the plate on the boom and moving the boom levers into the down a Skid Steer Loader position. Make sure the levers are locked and secure. -
Page 13: Maintenance
4. Torque the nut to 170 ft lbs. Carbide Teeth Replacement Note: Replace teeth whenever they become damaged, broken, or excessively worn. Excessively worn cutting edges greatly decrease cutting efficiency. Teeth are not a “warranty” part. Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 14: Cleaning And Storage
3. Disconnect the stump buster from the skid loader. Removing from Storage 1. Remove all protective coverings. 2. Tighten all loose bolts, nuts, and/or deterioration and replace if necessary. 3. Check hydraulic hoses for deterioration and replace if necessary. Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 15: Bolt Torque Chart
SAE 2 SAE 5 SAE 8 Diameter Wrench (Inches) Size lbs-ft lbs-ft lbs-ft 1/4" 7/16" 5/16" 1/2" 3/8" 9/16" 7/16" 5/8" 1/2" 3/4" 9/16" 13/16" 5/8" 15/16" 3/4" 1-1/8" 7/8" 1-5/16" 1" 1-1/2" 1020 1383 Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 16: Parts
GEAR BOX ASSY, RED W/BOLTS 300220 CAP SCREW 5/8 X 1/2 HH SC-50-53 GEAR BOX HUB/WHEEL ATTACH 300362 BOLT, HHCS M8-1.25 X 25 G8.8 ZN SC-127 COVER, HOSE 2.86” BLACK 700103 HOSE ASSY, HYD 3/4” x 87” Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 17: Sc-30-5 Gearbox Parts
SC-50-5Y Plug 3/8" Gas SC-25-5J Snap Ring For Holes SC-25-5D1 Bearing SC-25-5E Oil Seal 35x72x10 SC-25-5R1 Oil Seal 72x10 SC-25-5F Input Shaft SC-25-5X Shim SC-25-5N Castle Nut SC-50-53A SC-25-5V Pinion SC-25-5B7 Cotter Pin SC-25-5L Shim Shaver Manufacturing Company www.shavermfg.com 712-859-3293... -
Page 18: Warranty
12 consecutive months from the date of delivery of the new Shaver product to the original purchaser. Shaver Manufacturing Co., LLC. - Page 19 Notes Shaver Manufacturing Company www.shavermfg.com 712-859-3293...
- Page 20 Shaver Stumpbuster August 2014...
Need help?
Do you have a question about the SC-30H and is the answer not in the manual?
Questions and answers