Continuous Controller 파라미터; Destination (Dest) - Kurzweil Artis SE Musician's Manual

Continuous Controller 파라미터
• Mod Wheel
Continuous Controller Parameters
• 슬라이더 1-8
• Mod Wheel
• CC 페달
• Sliders 1 through 8
• CC Pedal
Destination (Dest)

Destination (Dest)

Use the Destination parameter to assign the Artis SE physical controllers (Sliders, Pedals,
Artis SE의 물리적 컨트롤러(슬라이더, 페달, 버튼, Mod Wheel 등)를 Program
Switches, Mod Wheel, etc.) to control Program parameters or send MIDI continuous
파라미터의 제어나 MIDI CC 메시지 전송(외부 MIDI 장비로)에 할당하고자 할
controller messages (CCs) to external MIDI gear.
때 사용합니다.
Destination 파라미터는 컨트롤러가 현재 선택한 Zone의 Program으로 보낼
controller will send to the Program in the currently selected Zone. By default, these CC
MIDI CC 번호를 결정합니다. 이러한 CC 메시지는 기본적으로 해당 Zone의
messages are also sent to the MIDI Out and USB ports on the Channel of that Zone
채널의 MIDI Out 단자와 USB 단자로도 보내집니다.
아래 CC 컨트롤러 번호 표는 각 Destination에 대한 기본 할당을 보여줍니다.
Programs respond to some of these CCs to do standard MIDI functions like volume and
Program은 Volume 및 Pan 같은 표준 MIDI 기능에 대한 일부 CC 값에 대응합니다.
panning. Other external MIDI gear (sound modules, computer software) may respond to
다른 외부 MIDI 장치(사운드 모듈, 컴퓨터 소프트웨어)도 표준 MIDI CC 메시지에
standard MIDI CC messages as well.
대응할 수 있습니다
Controller
Number
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14-15
16-19
20-26
27
28
26
30–31
Controller
Description
Destination
Bank MIDI Bank change message.
MWheel Default destination for Mod Wheel
Breath Default assignment for breath controller in compatible synths
MIDI 03 MIDI Controller 3
Foot Default assignment for continuous foot controller in compatible synths
PortTim Monophonic Artis SE Programs respond to this Controller if portamento is
turned on.
Data MIDI Controller 6.
Volume MIDI Volume
Balance MIDI Balance
MIDI 09 MIDI Controller 9
Pan MIDI Pan
Express Default assignment for CC Pedal. In most Programs it acts as a volume
control. It scales between 0 and the current value of Volume.
MIDI 12 Default assignment for Slider 5 (Filter-A Slider in Program Mode)
MIDI 13 Default assignment for Slider 6 (Filter-B Slider in Program Mode)
MIDI 14-15 MIDI Controllers 14-15
Ctl A - D MIDI Controllers 16-19
MIDI 20-26 MIDI Controllers 20-26
MIDI 27 Default assignment for Slider 7 (FX-A Slider in Program Mode. Sometimes
controls delay amount or another effect in Artis SE programs.)
MIDI 28 Default assignment for Slider 8 (FX-B Slider in Program Mode. Usually
controls reverb amount in Artis SE programs.)
MIDI 29 Default assignment for SW 1 in Program Mode. Usually enables a pad
layer or an effect in Program Mode.
MIDI 30–31 MIDI Controllers 30–31
Multi Edit Mode
Zone에 한정된 파라미터
Multi Edit Mode
85
8-11