Advertisement
Quick Links
This document explains how to install an I/O Option Board into a Kurzweil KSP8. The following I/O Option
boards are available for the KSP8:
Analog I/O Option Board
•
ADAT–TDIF I/O Option Board
•
AES I/O Option Board
•
mLAN (Firewire) I/O Option Board
•
These options are user-installable; no special expertise or special tools are required. Furthermore, the installation
procedure is the same for all the option boards. Usage instructions for the individual options are provided at the
end of this document.
IMPORTANT: The I/O option boards are not hot-swappable. You must turn off the KSP8 before you add or
remove an I/O option board.
Before Beginning the Installation
You should back up any objects (presets, chains, or studios) that you have created. You can either save the objects
to a SmartMedia card or dump the objects via MIDI using a SysEx dump. Refer to Chapter 10 of the KSP8 User's
Guide for information on these procedures.
Tools Required For Installation
#2 Phillips screwdriver
•
You will need access to the back panel of the KSP8.
Installation
1. Turn the unit off, then unplug all cables from the KSP8.
2. Using a #2 Phillips screwdriver, remove the two screws attaching the option slot cover plate to the
back panel of the KSP8. Set the screws aside so that you can use them to attach the option board.
The option slot cover plate is shown in Figure 1.
Young Chang Co., Ltd.
KSP8 I/O Option
Installation and Usage Guide
Subject to change without notice. All trademarks are the properties of their respective owners.
Part No. 910360, Rev. E
Advertisement
Related Manuals for Kurzweil KSP8 IO OPTION - REV E
Summary of Contents for Kurzweil KSP8 IO OPTION - REV E
- Page 1 KSP8 I/O Option Installation and Usage Guide This document explains how to install an I/O Option Board into a Kurzweil KSP8. The following I/O Option boards are available for the KSP8: Analog I/O Option Board • ADAT–TDIF I/O Option Board •...
- Page 2 Installation option slot cover plate Figure 1. Rear view of KSP8, showing location of option slot cover plate. Slide the I/O option board into the option slot as shown in Figure 2. Make sure the side edges of the board slide into the plastic rails inside the option slot. plastic rail Figure 2.
- Page 3 Using the KSP8 Analog I/O Option (KANA4) Using the KSP8 Analog I/O Option (KANA4) The Analog I/O Option adds four inputs and four outputs to your KSP8. The connectors are the same balanced 1/4" phone jacks that are used for the analog I/O on the stock KSP8, and their function is exactly the same. The only difference you will see will be on the Config INSEL and INLVL pages: The INSEL page will offer parameters Analog1 –...
- Page 4 Using the KSP8 ADAT–TDIF I/O Option (KADT8) Using the KSP8 ADAT–TDIF I/O Option (KADT8) The ADAT–TDIF I/O Option adds the following to your KSP8: eight digital inputs and outputs for the ADAT Optical Interface. • eight digital inputs and outputs for devices that use the TDIF format. •...
-
Page 5: Clock Source
Using the KSP8 ADAT–TDIF I/O Option (KADT8) 806 MnIn>5.1 AutoPan 807 3 SterIn>5.1 FX+ 808 4 SterIn>5.1 FX 809 5.1 In>5.1 FX + 810 Default 5.1+Ster 811 Default 8 Mono 812 Default 4 Stereo Master Table Master Page Configuration Parameters Some ADAT or TDIF configurations require that you set some of the parameters on the KSP8 Master page. - Page 6 Using the KSP8 ADAT–TDIF I/O Option (KADT8) Configuration and Connection Examples The examples below show the most effective way to use your KSP8 in a variety of situations. ADAT Optical Interface Device with ADAT KSP8 Optical Interface In Out For this configuration, you should make the following selections on the KSP8 Master and INSEL pages. StudioChanl: |||||SysEx|ID:|0 I/O|Config|:Studio|||||TDIF|Type:Other...
- Page 7 Using the KSP8 ADAT–TDIF I/O Option (KADT8) DA-88 TDIF Connection DA-88 KSP8 TDIF I/O For this configuration, you should make the following selections on the KSP8 Master and INSEL pages. StudioChanl: |||||SysEx|ID:|0 I/O|Config|:Studio|||||TDIF|Type:DA88|| ClockSource:TDIF|||||||TDIF|Len:16|Bit| DigWordLen|:16|Bit||||||||||||||||||||| DitherType|:Minimum|||||||||||||||||||| DigFormat||:AES/EBU||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||| In|1: In|5:TDIF|5|||||||| In|2:|TDIF|2|||||||||In|6:TDIF|6|||||||| In|3:|TDIF|3|||||||||In|7:TDIF|7|||||||| In|4:|TDIF|4|||||||||In|8:TDIF|8||||||||...
- Page 8 Using the KSP8 ADAT–TDIF I/O Option (KADT8) MOTU 2408 TDIF Connection MOTU 2408 KSP8 TDIF In Out ADAT NOTE: Clock Source must be ADAT For this configuration, you should make the following selections on the KSP8 Master and INSEL pages. StudioChanl: |||||SysEx|ID:|0 I/O|Config|:Studio|||||TDIF|Type:DA88||...
- Page 9 Using the KSP8 ADAT–TDIF I/O Option (KADT8) MOTU 2408 TDIF Connection with External Word Clock MOTU 2408 KSP8 TDIF Word Clock In Word Clock Outs External Word Clock Generator For this configuration, you should make the following selections on the KSP8 Master and INSEL pages. StudioChanl: |||||SysEx|ID:|0 I/O|Config|:Studio|||||TDIF|Type:Other|...
- Page 10 Using the KSP8 ADAT–TDIF I/O Option (KADT8) Yamaha Digital Mixer with TDIF Card KSP8 Yamaha digital mixer with TDIF card TDIF I/O For this configuration, you should make the following selections on the KSP8 Master and INSEL pages. StudioChanl: |||||SysEx|ID:|0 I/O|Config|:Studio|||||TDIF|Type:Other| ClockSource:TDIF|||||||TDIF|Len:16|Bit| DigWordLen|:16|Bit|||||||||||||||||||||...
- Page 11 Using the KSP8 AES I/O Option (KAES8) Using the KSP8 AES I/O Option (KAES8) The AES I/O Option adds four stereo input/output pairs to your KSP8. This option requires that the software revision level on your KSP8 be 1.7 or higher. The most current KSP8 software is provided on a SmartMedia card included with this option.
- Page 12 Using the KSP8 AES I/O Option (KAES8) Studio Configuration Files For your convenience, a configuration file named AESnn.KSP is provided on the included SmartMedia card. This file contains a subset of the base KSP8 studios with the appropriate input selections made, as well as a Master table that sets the Clock Source parameter to Option AES.
- Page 13 Using the KSP8 AES I/O Option (KAES8) Pinout for AES/EBU Connector The KSP8 AES Option uses a single DB-25 connector to provide four stereo input and output channels. While different manufacturers have used different standards in the pin assignments of these connectors for AES/EBU, the KSP8 employs the pinout used by the TASCAM DB-25 balanced connector.
-
Page 14: Cable Requirements
Using the KSP8 AES I/O Option (KAES8) Cable Requirements Cables for connecting the KSP8 AES Option should be constructed from shielded twisted-pair wiring with a nominal impedance of 110 ohms. The ground pins on each end of the cable connect to shields. The most common cable types are described below: DB-25 to 8 XLRs •... - Page 15 Using the KSP8 AES I/O Option (KAES8) DB-25 to DB-25 AES cable (male-to-male) with KSP8-type pinouts • This cable will have pinouts as shown in Table 1 for connection to any device that uses the same AES pinout as the KSP8, for example, the Panasonic DA7 digital mixer. Since the pinout is the same on each end of this cable, it must be wired in a crossover configuration, as shown in Table 2.
- Page 16 Using the KSP8 AES I/O Option (KAES8) DB-25 to DB-25 AES cable (male-to-male) with KSP8-type pinout at one end and Yamaha-type at other • The Yamaha-type connector uses the pinout shown in Table 3 for attaching a device such as a Yamaha 01V, 02R, or 03D digital mixer.
- Page 17 Table 4. Wiring for KSP8-type DB-25 to Yamaha-type DB-25 AES cable Cable Sources Conquest Sound – http://www.conquestsound.com/ • Redco Audio – http://www.redco.com/ • HosaTech – http://www.hosatech.com • Gig Cables – http://www.gigcables.com/CNdigital.html • Also check the Kurzweil web site (www.kurzweilmusicsystems.com) for any updates.
- Page 18 KSP8 mLAN I/O Option (KMLN8) KSP8 mLAN I/O Option (KMLN8) The mLAN I/O Option adds FireWire connectivity to your KSP8. This option requires that the software revision level on your KSP8 be 1.9 or higher. Complete documentation for the mLAN I/O Option is provided in a separate document (part number 910361).