For engineering change related to the use of silicone oil or other liquid, consult Xtemp engineer! The equipment is intended for heating, conditioning of specimen and/or application system by immersion in or external circulating of the liquids.
Page 5
Observe operating instructions! Warranty Requirements for warranty Xtemp Environments warrants the operational safety and functions of the equipment only under the conditions that: the equipment is operated and serviced exclusively in accordance with its intended purpose and as described in these Operating Instructions;...
The equipment shall be powered as for normal use and conditioned at its maximum operating temperature or 105°C, whichever is smaller, for at least 1h before commissioned for normal use. Warning, hazard of electric shock during the dry-out! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Connect the power from behind the equipment. Plug in and remove the cable by directly holding the plug. No dragging of cable in any part. Protect the cable from being damaged by contacting with the hot surface of the equipment or mouse etc! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Page 8
Caution, burn hazard! No draining of the heat transfer liquid with potential of chemical or biological hazard! Collect and identify the heat transfer liquid for future use! Consult Xtemp or manufacturer of the liquid for proper disposal! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD.
Page 9
Keep the cables and wiring protected by conduit and/or hose and well secured; keep them clearly away from direct contact with any exposed heated/cooled parts of the equipment and application system! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 8...
Page 10
Hydraulic tightness and fastening of drain device at three months intervals; Cutoff capability of the safety temperature limiter (STB) at 6 months intervals. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Voltage, frequency and current for power supply must meet the requirements as designated on the nameplate! Use power socket matching the power plug of the equipment. Hot line (L)and neutral line(N)for single phase equipment must not be reversed! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Flexible hose, fitting and coupling are important for the safe operation of the equipment; Use only hose, fitting and coupling provided with the equipment or recommended by Xtemp! The ratings of pressure and temperature for the hose, fitting and the jacket, container or heat...
However for temperature below ambient until minimum temperature range of the controller, optional cooling coil must be employed with additional external cooling source available. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 13...
The flow rate and direction at the external circulating return may also influence the performance and safety of the equipment! Reduced flow may produce an uneven circulating of the liquid and temperature distribution, while strong circulating may lead to overflow or splash of the XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
If an application system is connected, additional liquid may be necessary for appropriate level once initiated. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 15...
Page 17
The liquid level will change significantly with the immersion or removal of the specimen! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
While the actual temperature is lower than the Lt setting, the Lt may be set to a lower value by pressing so that Lt beeping can be cleared. If the actual temperature is XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Page 19
For example: 0 °C=32 °F, 212 °F=100 °C. dEFt :Return to the factory default setting. It may be used when system halts or any other abnormal situation occurs. ESc: Exit the SEt menu. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 18...
Set the working Press the button for SEt is first displayed, then press to enter, temperature less than 1 second change the digits by pressing accept the setting by pressing XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 19...
Page 21
1 cycle to 99 circles maximum and 0 means unlimited circles. Press to confirm and exist. Default parameters: t= 00:00, M=25, n=99 XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 20...
3) Set low temperature limit value Press for more than 2 seconds until Ht is displayed. Scroll the menu by until screen displays Lt . Press to enter Lt setting. Original Lt value is displayed, press XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 21...
Never move the equipment if the bath tank is fully filled with the heat transfer liquid; The liquid level may change with the heating and cooling of the equipment, and with the immersion or removal of the specimen! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Page 24
Caution, burn hazard! No draining of the heat transfer liquid with potential of chemical or biological hazard! Collect and identify the heat transfer liquid for future use! Consult Xtemp or manufacturer of the liquid for proper disposal! Install an extraction system over the bath opening, if the operating of the equipment could...
The timer starts to count down. When the time of AS elapses, the circulation fans will start automatically to initiate constant temperature control. Heating and constant temperature control executed automatically according to the difference between XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
The parameters are cycled and displayed for 2 times with each delay of about 2 seconds, and then exit automatically. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
The default unit for temperature measurements and setting is degree centigrade. The unit of temperature may be changed to Fahrenheit or Centigrade as desired. Refer to Table and item No. 4, use cF and similar steps for procedures. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
5) The liquid evaporates immediately from hot surface of the heater. Keep running dry for a couple of seconds until the Stb warning is displayed. Caution, Never run dry for more than 90 s! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C...
Secure the fuse once checked or replaced. For servicing or maintenance, call authorized service engineer. Fig 7 Location of the fuse and Pt100 sensor 81 Mains fuse (15A) 82 Terminal for Pt100 XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 28...
Reboot the controller again, if the equipment displays SPuP again, press (Fig 6-60) and ,the normal operation of the temperature control will resume. If warning still exists, and for servicing or maintenance, call authorized service engineer. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 29...
Immersion bath and external circulator in one unit, helps you to save money and make more space; Absolute temperature calibration (ATC) for accurate temperature control and AUTO- restart after power failure for continuous uninterrupted operation. XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 30...
(in) (10.4×17.9×20.5) Net weight Kg (lbs) 9 (19.8) Gross weight Kg (lbs) 11 (24.3) Voltage and frequency 115V~, 60Hz Current draw Specifications are subject to change without notice! XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. http://www.xtemp-usa.com/ DSGO0708-2-V211119/UXP8011-CD6400/CLASS I/NFL/RT+5~+100°C 31...