ESAB A2 PEK Instruction Manual
Hide thumbs
Also See for A2 PEK:
- Instruction manual (74 pages) ,
- Instruction manual (60 pages) ,
- Instruction manual (16 pages)
Related Manuals for ESAB A2 PEK
Summary of Contents for ESAB A2 PEK
- Page 1 A2, A6 Control panel Instruction manual 0460 949 174 GB 111222 Valid from program version 2.00...
-
Page 2: Table Of Contents
1 INTRODUCTION ........... 1.1 Control panel . - Page 3 6 FUNCTION EXPLANATIONS ........6.1 CA, constant amperage .
- Page 4 8 CONFIGURATION MENU ......... . . 8.1 Code lock .
-
Page 5: Introduction
12 Manual travel motion 13 Knob for setting the welding current / wire feed speed in the measurements menu, in other menus to increase or decrease the set values (settings knob) 14 Emergency stop - 5 - © ESAB AB 2009 bi24d1ea... -
Page 6: Keys And Knobs
Travel motion Key for travel motion in the direction of welding where the symbol is indicated on the weld equipment. To stop travel motion press The LED illuminates during travel motion. - 6 - © ESAB AB 2009 bi24d1ea... -
Page 7: First Step
This menu appears when the machine is first started: SAW: CA 450 Amp 30.0 Volt 50 cm/min GAS / NONE NONE FLUX NONE FUNCT The control panel is set to English on delivery. To select your language, proceed as follows: - 7 - © ESAB AB 2009 bi24d1ea... - Page 8 " CABLE LENGTHS panel. " MAINTENANCE " NETWORK SETTINGS QUIT Position the cursor on the row for your language and NORSK press ENTER. POLSKI PORTUGUES SUOMI SVENSKA CHINESE - 8 - © ESAB AB 2009 bi24d1ea...
-
Page 9: Unit Of Measurements
Press ENTER to QUALITY DATA LOG TO FILE bring up a list of the SOFT KEYS SETUP" mesurements that are AUTO SAVE MODE available in the control UNIT OF LENGTH METRIC panel. QUIT - 9 - © ESAB AB 2009 bi24d1ea... -
Page 10: Display
1.3.1 Symbols in the display The selected weld data set Welding direction A fault has occurred. See chapter Recalled memory position number Scroll bar. Further information can be found in this menu - 10 - © ESAB AB 2009 bi24d1ea... -
Page 11: General Information About Settings
QUIT returns you to the previous menu or image. Pressing ENTER entails the execution of a selected choice in a menu or a list. key is called ENTER in this manual. - 11 - © ESAB AB 2009 bi24d1ea... -
Page 12: Menus
REGULATION TYPE method, wire dimension WIRE TYPE Fe SOLID etc. WIRE DIMENSION 0.8 mm You can access other " CONFIGURATION sub menus from this " TOOLS menu. FAST MEASURE MEMORY MODE - 12 - © ESAB AB 2009 bi24d1ea... - Page 13 EXPORT / IMPORT production statistics, " FILE MANAGER error logs, etc. " SETTING LIMIT EDITOR " MEASURE LIMIT EDITOR " PRODUCTION STATISTICS " QUALITY FUNCTIONS " CALENDAR " USER ACCOUNTS " UNIT INFORMATION QUIT - 13 - © ESAB AB 2009 bi24d1ea...
- Page 14 SAW WELD DATA SETTING menu VOLTAGE 24,0 V CURRENT 3200 A TRAVEL SPEED 30 cm/min DIRECTION AC FREQUENCY 50 HZ AC BALANCE AC OFFSET " START DATA " STOP DATA " REGULATION PAR. QUIT - 14 - © ESAB AB 2009 bi24d1ea...
- Page 15 The settings knobs can be used to change the welding parameters in the measurement display. If the set value is changed when welding is not in progress, the measurement value changes to zero. - 15 - © ESAB AB 2009 bi24d1ea...
- Page 16 7 (GMAW) and copy various set weld data. The weld data sets can be stored in 255 different memory positions. STORE FUNCT QUIT For further information, see the chapter 7 “Memory management”. - 16 - © ESAB AB 2009 bi24d1ea...
- Page 17 Choose between constant welding current CA or constant wire feed CW or constant current CC, see explanation in chapter 6.1, and 6.3. If cold wire feed is selected, see chapter 8.3.9, only regulation type CW can be selected. - 17 - © ESAB AB 2009 bi24d1ea...
- Page 18 Auto Inductance Auto or Set values Auto Setting limits Measure limits The setting range is dependent on the product used. The menu shows the settings that belong to the selected regulation type. - 18 - © ESAB AB 2009 bi24d1ea...
- Page 19 0 - 10 s 0.01 s Stop phases OFF or ON Dynamic regulation Auto or Set value Auto Setting limits Measure limits *) The setting range is dependent on the product used. - 19 - © ESAB AB 2009 bi24d1ea...
- Page 20 0 - 10 s 0.01 s Stop phases OFF or ON Dynamic regulation Auto or Set value Auto Setting limits Measure limits *) The setting range is dependent on the product used. - 20 - © ESAB AB 2009 bi24d1ea...