ESAB A2 PEK Instruction Manual
Pek control unit
Hide thumbs
Also See for A2 PEK:
- Instruction manual (74 pages) ,
- Instruction manual (20 pages) ,
- Instruction manual (18 pages)
Subscribe to Our Youtube Channel
Related Manuals for ESAB A2 PEK
Summary of Contents for ESAB A2 PEK
- Page 1 A2, A6 Control unit Instruction manual 0460 948 001 GB 110119 Valid for serial no. 921-xxx-xxx, 943-xxx-xxxx, 049-xxx-xxxx...
-
Page 2: Declaration Of Conformity
PEK Control box is used with A2 and A6, from serial number 921 xxx xxxx (2009 w. 21) Manufacturer or his authorised representative established within the EEA Name, address, telephone No, telefax No: Tillverkarens namn, adress, telefon, telefax: ESAB AB, Welding Equipment Esabvägen, SE−695 81 LAXÅ, Sweden Phone: +46 584 81 000, Fax: +46 584 411 924 The following harmonised standard in force within the EEA has been used in the design: Följande harmoniserande standarder har använts i konstruktionen:... -
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. - Page 5 WARNING Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard data. ELECTRIC SHOCK - Can kill Install and earth the unit in accordance with applicable standards. Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
-
Page 6: Introduction
For further information contact the nearest ESAB dealer. ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION PEK is a control unit intended for submerged arc welding (SAW) and for gas metal arc welding (GMAW). -
Page 7: Technical Data
TECHNICAL DATA Supply voltage 42 V, 50/60 Hz Power requirement Max 900 VA Engine connections adapted for ESAB's 6 A 100% motors Speed control Reconnection from motor with pulse sensor -15° C to + 45 ° C Operating temperature -20° C to + 55 ° C... -
Page 8: Operation
Certain USB memories may not work with this equipment. We recommend using USB memories from a reputable supplier. ESAB assumes no responsibility for any damage caused as a consequence of incorrect use of the USB memory. - 8 -... -
Page 9: Key To Symbols
To insert a USB memory Switch off the power supply main switch. Insert the USB memory into the USB socket. Switch on the power supply main switch. Key to symbols Main menu Enter Manual travel motion in Manual travel motion in direction Y direction J Manual wire feed... -
Page 10: Maintenance
EN 60974-1 and EN 60974-10. It is the obligation of the service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard. Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - 10 -... - Page 11 - 11 -...
-
Page 12: Diagram
Diagram Edition 110119... - Page 13 Edition 110119...
-
Page 14: Ordering Number
Ordering number Ordering no. Denomination Type 0460 504 880 Control unit 0459 839 036 Spare parts list 0460 949 Instruction manual Control panel for PEK Instruction manuals and the spare parts list are available on the Internet at www.esab.com Edition 110119... -
Page 15: Accessories
Accessories Control cable PEK - Power source 15 m ........0460 910 881 25 m . - Page 16 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the A2 PEK and is the answer not in the manual?
Questions and answers