Serial And Ir Insertion Connections; Control Connections; Switcher Reset; Power - Extron electronics DTP CrossPoint 84 Setup Manual

Serial and IR Insertion Connections

RS-232
1 2
3 Tx Rx G Tx Rx
SIG LINK
OVER TP
XTP
RS-232
DTP
HDBT OUT Tx Rx G Tx Rx
5
1 2 3 4
Figure 5.
O
Over TP (Inputs 7 and 8) Ports
signals, or both into these 3.5 mm, 5-pole captive screw connectors to insert
bidirectional RS-232 and IR communications (see
on page 11 to wire the connectors).
P
Over TP (Outputs 3 and 4) Ports
signals, or both into these 3.5 mm, 5-pole captive screw connectors to insert
bidirectional RS-232 and IR communications (see
on page 11 to wire the connectors).

Control Connections

Tx Rx
REMOTE LAN
Tx Rx G
R
Figure 6.
NOTE: Figure 6 is a composite that shows features of all models. Specific models can
have either a LAN port (item
but not both.
Q
LAN (Ethernet) port
a control system, or a computer to the Ethernet RJ-45 port (see
page 8 to wire the connector).
NOTE: The factory default IP address is 192.168.254.254.
IPCP
R
include a built-in control processor that can control and monitor a variety of external
devices. The IPCP offers RS-232 and IR-based control, relays, and digital I/O controls.
See the
and to configure and operate the IPCP control processor.
Remote Port — Plug a serial RS-232 device into the matrix switcher via this
S
3.5 mm, 3-pole captive screw connector for remote control of the switcher
(see RS-232 and IR connectors

Switcher Reset

Switcher Reset button and LED — Initiates four levels of For different
T
reset levels, press and hold the recessed button while the switcher is running or
while you power up the switcher.
See the DTP CrossPoint 84 Series User Guide, available at www.extron.com.

Power

Power connector — Plug the switcher into a grounded AC source.
U
DTP CrossPoint 84 • Installation
IR
4 4
S/PDIF
SIG LINK OUT
XTP
IR
DTP
OUT
HDBT
RS-232 IR
6 8
Tx Rx G Tx Rx
SIG LINK SIG LINK
OVER TP
XTP XTP
RS-232 IR
DTP IN Tx Rx G Tx Rx IN DTP
Serial and IR Insertion Connections
— Plug serial RS-232 signals, modulated IR
— Plug serial RS-232 signals, modulated IR
COM 1 COM 2 COM 3 DIGITAL I/O
LAN 1
G RTS CTS Tx Rx G Tx Rx G 1 2 3 4 G
IR/SERIAL RELAYS eBUS
1 2 1 2 C 3 4 C +V +S -S G
S G S G PWR OUT = 6W
LAN 2 LAN 3
IPCP Control Processor and Remote Port
, below) or a control processor
Q
(non-IPCP model) — If desired, connect a network WAN or LAN hub,
(IPCP models)—(see
control processor
IPCP Pro Series Setup Guide
RS-232 and IR connectors
RS-232 and IR connectors
figure 2
on page 4)The IPCP models
, included with the switcher, to make all connections
on page 11 to wire the connector).
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
(item R on page 8),
TP connectors on
REMOTE
Tx Rx G
RESET
7