Subscribe to Our Youtube Channel
Related Manuals for WOOSIM WSP-P440
Summary of Contents for WOOSIM WSP-P440
- Page 1 WSP-P440 MODEL (4inch Panel Printer) Rev 4.2 All specifications are subjected to change without notice http://www.woosim.com...
- Page 2 Copyright ⓒ2021 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim System Inc. Trademark a registered trademark of Woosim Systems Inc.
- Page 3 P440 Rev. 4.2 Introduction The WSP-P440 is an extremely simple and functional panel printer. It is the ideal solution for applications which require the immediate printing of data on a paper, whether they be of an industrial, professional or laboratory nature.
- Page 4 Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. http://www.woosim.com 2021-12-23...
-
Page 5: Table Of Contents
3.1. UART(RS-232C or TTL) ............................14 4. Using the printer ..............................15 4.1. Control panel ............................... 15 4.2. The self test ................................. 15 5. Consumable Parts ..............................16 5.1. Recommended paper............................16 5.2 Printing position ..............................16 6. Revision History ..............................17 http://www.woosim.com 2021-12-23... -
Page 6: Outline
2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported. But some of the interfaces are not supported according to the product and please contact us, if you have any questions regarding the interface. http://www.woosim.com 2021-12-23... -
Page 7: Specifications
** CORE : ZCAT2035-0930 (TDK Corporation) -10°C ~50°C (operating) Temperature -30°C ~ 70°C (storage) Environment conditions 30% - 80% (operating) Humidity 10% - 90% (storage) Mechanical 37,000,000 lines MCBF (Mean Cycle Between failure) Head Approximately 50Km < Table 1 > http://www.woosim.com 2021-12-23... -
Page 8: Setting Up The Printer
P440 Rev. 4.2 2.1. Printer & Accessories When unpacking your printer box make sure it contains the printer and all accessories. If any accessories are missing or damage, please contact your dealer for assistance. Thermal roll paper WSP-P440 http://www.woosim.com 2021-12-23... -
Page 9: Printer Features
P440 Rev. 4.2 2.2. Printer Features [unit : mm] http://www.woosim.com 2021-12-23... -
Page 10: Panel Installation
P440 Rev. 4.2 2.3. Panel Installation Uses the bracket(option) and the printer once more will be able to fix to the panel. http://www.woosim.com 2021-12-23... -
Page 11: Replacing The Paper Roll
2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.woosim.com 2021-12-23... -
Page 12: Setting Operation Mode
And then the density has set to 2 stop bit. When you press FEED Button once again, Power Lamp flickers 6 times Error Lamp flickers once. Press MODE Button twice, Error Lamp flickers 3 times. And then the density has set to Density high. http://www.woosim.com 2021-12-23... -
Page 13: Power Supply
Density High < Table 2 > 2.6. Power supply The following specifications are requested for Power supply. INPUT POWER: 7.5~8.5VDC / 3A or more Avoid using power supply which its power capacity of power current is extremely high. http://www.woosim.com 2021-12-23... -
Page 14: Interface
P440 Rev. 4.2 3.1. UART(RS-232C or TTL) The WSP-P440 printer has a UART(RS-232C or TTL) interface and power connector is connected by 6 pin female connector. In the following table, the signals present on the connector are listed: Pin no. -
Page 15: Using The Printer
3. Printer will print out the current status. (F/W version and set contents) 4. And then pattern of characters will be printed out. 5. Self-test will be finished automatically and turned to the standby status. ※ In case printer does not work properly, please contact Woosim customer service center. http://www.woosim.com 2021-12-23... -
Page 16: Consumable Parts
2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70℃. Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc. 5.2 Printing position http://www.woosim.com 2021-12-23... -
Page 17: Revision History
* Delete address 7,8,14p Input Power modify : 9VDC, Standby 60mA and Max 3A → DC7.5~8.5V (MAX 9VDC) Sep. 07. 2018 Standby 60mA and 3A or more Serial&Power connector modify 8P → 6P Oct. 13. 2021 Add Core spec. http://www.woosim.com 2021-12-23...
Need help?
Do you have a question about the WSP-P440 and is the answer not in the manual?
Questions and answers