Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-020
Summary of Contents for Humandata XCM-020
- Page 1 Spartan-6 LXT FPGA Board XCM-020 Series User’s Manual Ver. 1.0 HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction ....................1 1. Shared Pins [IMPORTANT] ................2 2. Specifications ..................... 3 3. Overview ......................4 3.1. Name of Parts .......................4 3.2. Block Diagram ......................5 3.3. Power Supply ......................6 3.4. Clock ........................6 3.5. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Initial release Introduction Thank you for buying our product XCM-020. This is an evaluation board equipped with a XILINX FPGA Spartan-6 LXT, voltage regulators, oscillators and configuration device. It can provide you with very convenient and easy-to-use development environment. -
Page 5: Shared Pins [Important]
To prevent these pins from being shorted out, it is recommended to set them as “Float” in advance. Please refer to the following steps and check the “Unused IOB Pins” setting. 1. Right click [Generate Programming File] and open [Process Properties] window. 2. Confirm [Unused IOB Pins] in [Configuration Options]. XCM-020 Series v1.0... -
Page 6: Specifications
SIL 7-pin socket, 2.54 [mm] pitch Status LEDs Power (red), Done (blue) SIL 7-pin header (Mounted) x1 Accessories DIL 80-pin header (Cuttable) x 2 RoHS Compliance * There may be cases that these parts and specifications are changed. XCM-020 Series v1.0... -
Page 7: Overview
3. Overview 3.1. Name of Parts Reference clocks User I/O (CNB) User Switches Power LED User LEDs Serial I/F JTAG SIF40 Done LED Config. SW Oscillators User I/O (CNA) Component Side MRAM * Not for LX75T Solder Side XCM-020 Series v1.0... -
Page 8: Block Diagram
J TAG B uffer Power Circuit 2 .5V, 1.2V 1 .8V, 0.9V C onfig. Switch Power LED (3.3V) 5 0 GPIO U se r I/Os CNA 3 .3 V INPUT E xt . Clock (option) X CM-020 Rev.A XCM-020 Series v1.0... -
Page 9: Power Supply
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. You can use Xilinx download cable. Pin No. Signal Name Direction VCC (3.3V) OUT (POW) Notice Please pay attention not to attach cables in reverse. XCM-020 Series v1.0... -
Page 10: Configuration Switch (Sw1)
You can set status of user I/O pins before and during FPGA configuration. ON : Pull-Up OFF : No Pull-Up (High impedance) X_M1 Configuration mode select pins. The modes showed above are a part of all. ASW0, ASW1 You can use this as user switch. XCM-020 Series v1.0... -
Page 11: Gtp Transceiver (Rocketio)
For reference clock, 125 MHz and 150 MHz oscillators are equipped. By changing PJ1 and PJ2 position, external reference clock is available via MMCX connector. For more details, please refer to the circuit schematic. * SIF40 is the interface standard for fast transceivers by HuMANDATA. XCM-020 Series v1.0... -
Page 12: Fpga Configuration
Please set FPGA configuration mode to [Master Serial/SPI]. 7. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-020/ Circuit Schematic Pin List Dimensional drawing Net List … and more. XCM-020 Series v1.0... - Page 13 Spartan-6 LXT FPGA Board XCM-020 Series User’s Manual Ver. 1.0 ..........Jun. 15, 2011 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-72-620-2002 (Japanese) Fax: 81-72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)