Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-108-700AN
Summary of Contents for Humandata XCM-108-700AN
- Page 1 Spartan-3AN FPGA Board XCM-108-700AN User’s Manual HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction......................1 1. Specifications......................2 2. Overview........................ 3 2.1. Name of Parts ....................3 2.2. Block Diagram ....................4 2.3. Power Supply ..................... 4 2.4. JTAG Connector....................5 3. Configuration Switch..................... 6 4. FPGA Configuration ....................7 5. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Jul. 15, 2009 Initial release Introduction Thank you for buying our product XCM-108-700AN. This is an evaluation board equipped with a Xilinx FPGA Spartan-3AN, power, reset, and clock circuit. It can provide you with very convenient and easy-to-use environment. -
Page 5: Specifications
6 Layer FR-4 t1.6 [mm] Immersion gold Dimensions 1.693" x 2.126" (43 x 54 [mm]) Weight 17 [g] typ. User I/O Connectors FX10A-80P/8-SV1 (71) SIL 7-pin header (Mounted) Accessories 2 FX10A-80S/8-SV (71) RoHS Compliance * There may be cases when compatible parts are used. XCM-108-700AN v1.0... -
Page 6: Overview
2. Overview 2.1. Name of Parts User LED User Switch Oscillator 50 MHz Power Circuit JTAG FPGA AWAKE LED Config. Switch DONE LED Power LED Component Side User I/Os (CNA) Unusable User I/Os (CNB) Solder Side XCM-108-700AN v1.0... -
Page 7: Block Diagram
This board opera tes from single DC 3.3 V power supply. The external power supply should be sufficient and stabi lized. Notes Please apply power to CNA and CNB with thick print pattern or cable. Please connect all ground pins. XCM-108-700AN v1.0... -
Page 8: Jtag Connector
This connector is used to configure the FPGA and program the internal configuration device in-system. Pin assignment is as follows. Signal Name Direction JTAG Pin VCC(3.3V) OUT(POW) You can use Xilinx download cable. Notice Please pay attention not to attach cables in reverse. XCM-108-700AN v1.0... -
Page 9: Configuration Switch
2 - 4 : Mode Select Please see the table above. 5 - 7 : SPI Configuration Mode Please see a Spartan-3AN data sheet for more details. 8 : Suspend Please see a Spartan-3AN data sheet for more details. XCM-108-700AN v1.0... -
Page 10: Fpga Configuration
10. Click [Boundary Scan] in [Configuration Mode] window. 11. Select the configuration device icon, then open [Operations] and click [Program]. 12. Check [Verify] and [Erase Before Programming], then click [OK]. Then it will show you the message “Program Succeeded”. XCM-108-700AN v1.0... -
Page 11: Additional Documentation And User Support
6. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-108/ Circuit Schematic Pin List Dimensional drawing PCB drawing Net List … and more. XCM-108-700AN v1.0... - Page 12 Spartan-3AN FPGA Board XCM-108-700AN User’s Manual Ver. 1.0 ..........Jul. 15, 2009 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-(0)72-620-2002 (Japanese) Fax: 81-(0)72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)