Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-018Z
Summary of Contents for Humandata XCM-018Z
- Page 1 Spartan-6 FPGA Board XCM-018Z Series User’s Manual Ver. 1.0 HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction ....................1 1. Share Pins [IMPORTANT] ................. 2 2. Specifications ..................... 3 3. Overview ......................4 3.1. Name of Parts .......................4 3.2. Block Diagram ......................5 3.3. Power Supply ......................5 3.4. Clock ........................6 3.5. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Initial release Introduction Thank you for buying our product XCM-018Z. This is an evaluation board equipped with a Xilinx FPGA Spartan-6, voltage regulators, configuration reset circuit, oscillators and configuration device. It can provide you with very convenient and easy-to-use development environment. -
Page 5: Share Pins [Important]
To prevent these pins from being shorted out, it is recommended to set them as “Float” in advance. Please refer to the following steps and check the “Unused IOB Pins” setting. 1. Right click [Generate Programming File] and open [Process Properties] window. 2. Confirm [Unused IOB Pins] in [Configuration Options]. XCM-018Z Series v1.0... -
Page 6: Specifications
1.0 [mm], 100[mil]/2.54 [mm] pitch JTAG Connector SIL 7-pin socket, 2.54 [mm] pitch SIL 7-pin header (Mounted) x1 Accessories DIL 80-pin header (Cuttable) x 2 RoHS Compliance * There may be cases that these parts and specifications are changed. XCM-018Z Series v1.0... -
Page 7: Overview
3. Overview 3.1. Name of Parts Oscillator 30 MHz User I/Os (CNB) Config. Device Config. Switch JTAG Serial I/F Status LEDs User LEDs User Switches User I/Os (CNA) Oscillator 50 MHz Component Side Solder Side XCM-018Z Series v1.0... -
Page 8: Block Diagram
The external power supply should be sufficient and stabilized. Please do not apply over 3.3V voltage. VCCIO in BANK B is not connected to 3.3V. Please input given voltage from CNB. For more details, please refer to circuit schematics and FPGA data sheet. XCM-018Z Series v1.0... -
Page 9: Clock
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. You can use Xilinx download cable. Pin No. Signal Name Direction VCC (3.3V) OUT (POW) Notice Please pay attention not to attach cables in reverse. XCM-018Z Series v1.0... -
Page 10: Configuration Switch (Sw4)
You can set status of user I/O pins before FPGA configuration. ON : Pull-Up OFF : Non-Pull-Up (High impedance) M0, M1 Configuration mode select pins. The modes showed above are a part of all. ASW0 You can use this as user switch. XCM-018Z Series v1.0... -
Page 11: Fpga Configuration
Assign the mcs file to Flash icon and choose [SPI PROM – M25P32] or [SPI PROM – M25P64] for device type, then right click and select a command. Please set FPGA configuration mode to [Master Serial/SPI] mode. XCM-018Z Series v1.0... -
Page 12: Additional Documentation And User Support
6. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-018Z/ Circuit Schematic Pin List Dimensional drawing Net List … and more. XCM-018Z Series v1.0... - Page 13 Spartan -6 FPGA Board XCM-018Z Series User’s Manual Ver. 1.0 ..........Dec. 13, 2010 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-72-620-2002 (Japanese) Fax: 81-72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)