Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-015
Summary of Contents for Humandata XCM-015
- Page 1 Spartan-3A FPGA Board XCM-015 Series User’s Manual HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction......................1 1. Specifications......................2 2. Overview........................ 3 2.1. Name of Parts ....................3 2.2. Block Diagram ....................4 2.3. Power Supply ..................... 4 2.4. JTAG Connector....................5 3. Configuration Switch..................... 6 4. FPGA Configuration ....................7 5. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Nov. 4, 2009 Initial release Introduction Thank you for buying our product XCM-015. This is an evaluation board equipped with a Xilinx FPGA Spartan-3A, power, reset, and clock circuit and configuration device. It can provide you with very convenient and easy-to-use environment. -
Page 5: Specifications
Weight 30 [g] typ. User I/O Connectors 80-pin through-hole dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch SIL 7-pin header (Mounted) Accessories 2 DIL 80-pin headers (Cuttable) RoHS Compliance * There may be cases when compatible parts are used. XCM-015 Series v1.0... -
Page 6: Overview
2. Overview 2.1. Name of Parts User LEDs User I/Os (CNB) Oscillator User Switch 50 MHz DDR2 SDRAM SPI-PROM JTAG Serial I/F Config. Switch FPGA Status LEDs User I/Os (CNA) Component Side FRAM Solder Side XCM-015 Series v1.0... -
Page 7: Block Diagram
This board operates from single DC 3.3 V power supply. The external power supply should be sufficient and stabilized. Notes Please apply power to CNA and CNB with thick print pattern or cable. Please connect all ground pins. XCM-015 Series v1.0... -
Page 8: Jtag Connector
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. Signal Name Direction JTAG Pin VCC(3.3V) OUT(POW) You can use Xilinx download cable. Download Cable Notice Please pay attention not to attach cables in reverse. XCM-015 Series v1.0... -
Page 9: Configuration Switch
5 - 7 : Mode Select Please see the table above. 2 - 4 : SPI Configuration Mode Please see a Spartan-3A data sheet for more details. 1 : Suspend Please see a Spartan-3A data sheet for more details. XCM-015 Series v1.0... -
Page 10: Fpga Configuration
9. Select [Part Name] same as which is on the board. 10. Check [Verify] and [Erase Before Programming] in [Device Programming Properties] tab. 11. Select SPI PROM icon, then open [Operation] and click [Program]. Then it will show you the message “Program Succeeded”. XCM-015 Series v1.0... -
Page 11: Configuration Rate
2. Change [Configuration Rate] value in [Configuration Options]. 7. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-015/ Circuit Schematic Pin List Dimensional drawing PCB drawing Net List … and more. XCM-015 Series v1.0... - Page 12 Spartan-3A FPGA Board XCM-015 Series User’s Manual Ver. 1.0 ..........Nov. 4, 2009 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-(0)72-620-2002 (Japanese) Fax: 81-(0)72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)