Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-301-200
Summary of Contents for Humandata XCM-301-200
- Page 1 Spartan-3 FPGA Board XCM-301-200 User’s Manual HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction ....................1 1. Specifications ..................... 2 2. Overview ......................3 2.1. Name of Parts .......................3 2.2. Block Diagram ......................4 2.3. Power Supply ......................4 2.4. JTAG Connector ....................5 3. Jumper Pins ....................... 6 3.1. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Jul. 15, 2009 Initial release Introduction Thank you for buying our product XCM-301-200. This is an evaluation board equipped with a Xilinx FPGA Spartan-3, power, reset, and clock circuit and configuration device. It can provide you with very convenient and easy-to-use environment. -
Page 5: Specifications
2.087" x 2.126" (53 x 54 [mm]) Weight 14 [g] typ. User I/O Connectors 40-pin through-hole dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch 2 Jumper socket Accessories 2 DIL 40-pin headers (Cuttable) RoHS Compliance * There may be cases when compatible parts are used. XCM-301-200 v1.0... -
Page 6: Overview
2. Overview 2.1. Name of Parts DONE LED User I/Os (CNB) Config. Device Power & POR JTAG User LED FPGA Oscillator Power LED 48MHz User Switch User I/Os (CNA) Component Side XCM-301-200 v1.0... -
Page 7: Block Diagram
This board operates from single DC 3.3 V power supply. The external power supply should be sufficient and stabilized. Notes Please apply power to CNA and CNB with thick print pattern or cable. Please connect all ground pins. XCM-301-200 v1.0... -
Page 8: Jtag Connector
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. Signal Name Direction VCC (3.3V) OUT (POW) You can use Xilinx download cable. Notice Please pay attention not to attach cables in reverse. XCM-301-200 v1.0... -
Page 9: Jumper Pins
M2 = 0 : JP2 Short JTAG mode M0 = 1 : JP2 Open M1 = 0 : Fixed M2 = 1 : JP2 Open 3.2. Other Pins JP1 : HSWAP ENABLE pin Short : L Open : H XCM-301-200 v1.0... -
Page 10: Fpga Configuration
8. Click [Boundary Scan] in [Configuration Mode] window. 9. Select the configuration device icon, then open [Operations] and click [Program]. 10. Check [Verify] and [Erase Before Programming], then click [OK]. Then it will show you the message “Program Succeeded”. XCM-301-200 v1.0... -
Page 11: Additional Documentation And User Support
6. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-301/ Circuit Schematic Pin List Dimensional drawing PCB drawing Net List … and more. XCM-301-200 v1.0... - Page 12 Spartan-3 FPGA Board XCM-301-200 User’s Manual Ver. 1.0 ..........Jul. 15, 2009 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-(0)72-620-2002 (Japanese) Fax: 81-(0)72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)