Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-019
Summary of Contents for Humandata XCM-019
- Page 1 Spartan-6 FPGA Board XCM-019 Series User’s Manual Ver. 1.1 HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction ....................1 1. Specifications ..................... 2 2. Overview ......................3 2.1. Name of Parts .......................3 2.2. Block Diagram ......................4 2.3. Power Supply ......................4 2.4. Clock ........................5 2.5. JTAG Connector ....................5 2.6. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Change: Level Converter Introduction Thank you for buying our product XCM-019. This is an evaluation board equipped with a Xilinx FPGA Spartan-6, voltage regulators, configuration reset circuit, oscillators and configuration device. Equipped 5V I/O level converters help you to control 5V interfaces with Spartan-6. -
Page 5: Specifications
SIL 7-pin socket, 2.54 [mm] pitch Power (red) x1 Status LEDs Done (blue) x1 SIL 7-pin header (Mounted) x1 Accessories DIL 80-pin header (Cuttable) x 2 RoHS Compliance * There may be cases that these parts and specifications are changed. XCM-019 Series v1.1... -
Page 6: Overview
2. Overview 2.1. Name of Parts User I/Os (CNB) User Switches Oscillator 30 MHz JTAG Serial I/F Config. Device User LEDs Oscillator 50 MHz Config. SW User I/Os (CNA) Component Side Level Converters Solder Side XCM-019 Series v1.1... -
Page 7: Block Diagram
Internally required 3.3 [V] and 1.2 [V] are generated by on-board voltage regulators. The external power supply should be sufficient and stabilized. Please do not apply over 5.0 V voltage. For more details, please refer to circuit schematics and FPGA data sheet. XCM-019 Series v1.1... -
Page 8: Clock
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. You can use Xilinx download cable. Pin No. Signal Name Direction OUT (POW) Notice Please pay attention not to attach cables in reverse. XCM-019 Series v1.1... -
Page 9: Configuration Switch (Sw1)
Generally, users do not need to be attentive to mode setting for JTAG configuration. But for this product, it is recommended to set the mode as shown above. ASW0 You can use this as user switch. XCM-019 Series v1.1... -
Page 10: Fpga Configuration
Select your bit file, and generate MCS file. 4.2. Programming Configuration Device Assign the mcs file to Flash icon and choose [SPI PROM – M25P32] for device type, then right click and select a command. Please set FPGA configuration mode to [Master Serial/SPI] mode. XCM-019 Series v1.1... -
Page 11: Additional Documentation And User Support
5. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-019/ Circuit Schematic Pin List Dimensional drawing Net List … and more. XCM-019 Series v1.1... - Page 12 Spartan-6 FPGA Board XCM-019 Series User’s Manual Ver. 1.1 ..........Oct. 10, 2017 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-72-620-2002 (Japanese) Fax: 81-72-620-2003 (Japanese/English) URL: https://www2.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)