1. Manuals
  2. Brands
  3. Vigilantplant Manuals
  4. Wireless Access Point
  5. WFC009
  6. User manual

Vigilantplant WFC009 User Manual

Field wireless access point
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User's
Manual
YFGW510
Field Wireless Access Point
IM 01W02E01-01EN
IM 01W02E01-01EN
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Vigilantplant WFC009

Summary of Contents for Vigilantplant WFC009

  • Page 1 User’s Manual YFGW510 Field Wireless Access Point IM 01W02E01-01EN IM 01W02E01-01EN 1st Edition...
  • Page 2 Blank Page...

  • Page 3: Table Of Contents

    Toc-i YFGW510 Field Wireless Access Point IM 01W02E01-01EN This document contains important information about using the YFGW510 field wireless access point properly and safely. Please read this document thoroughly before using this product. The configuration of the field wireless system is described in the User’s Manual of the YFGW410 field wireless management station (IM 01W02D01-01EN).
  • Page 4 Toc-ii PART-B. FUNCTIONS OF YFGW510 Functions of YFGW510 ................B1-1 Structure and Parts of YFGW510 ............B2-1 B2.1 Front View ....................... B2-1 B2.2 Rear View ......................B2-2 B2.3 Side View ......................B2-4 LED Display Function ................B3-1 Mechanical Operating Parts ..............B4-1 Checking the Product ................B5-1 IM 01W02E01-01EN...
  • Page 5 Toc-iii PART-C. INSTALLATION Installation Environment ...............C1-1 Power Supply and Grounding ..............C2-1 C2.1 Power Supply ....................C2-1 C2.2 Grounding ....................... C2-1 Requirements for Installation ...............C3-1 C3.1 Requirements for Installation Locations ............. C3-1 C3.2 Notes on Installation ..................C3-2 Mounting ....................C4-1 Wiring .......................C5-1 C5.1 Power Supply Cable Connection ..............
  • Page 6 Toc-iv PART-D. SETUP Initial Configuration ................D1-1 Setup Tool ....................D2-1 D2.1 System Requirements ................... D2-1 D2.1.1 Hardware ..................D2-1 D2.1.2 Software ..................D2-1 D2.1.3 Connection Example ............... D2-2 D2.2 Installation Procedure ................... D2-3 D2.2.1 Driver for Infrared adapter ............... D2-3 D2.2.2 Field Wireless Access Point Setup Tool ..........
  • Page 7 Toc-v PART-E. OPERATION AND MAINTENANCE Routine Maintenance ................E1-1 Additions and Replacements ..............E2-1 Maintenance in Hazardous Areas ............E3-1 Components Having Defined Life Spans ..........E4-1 IM 01W02E01-01EN...
  • Page 8 Toc-vi PART-F. TROUBLESHOOTING Status Information .................. F1-1 Status Indication and Responsive Measures ........F2-1 IM 01W02E01-01EN...
  • Page 9 Toc-vii PART-G. SPECIFICATIONS Standard Specifications ............... G1-1 G1.1 Communication Interface Specifications ............ G1-1 G1.2 General Specifications .................. G1-2 G1.3 Regulatory Compliance Statements ............G1-3 Model, Suffix Codes and Option Codes ..........G2-1 External Dimensions ................G3-1 G3.1 100BASE-TX/100BASE-FX Specifications ..........G3-1 G3.2 Single Communication Wireless LAN Client Specifications ....

  • Page 10: Introduction

    <Read Me First> Introduction This document describes the YFGW510 field wireless access point, which is a core component of field wireless networks. conforming to ISA100.11a, a wireless communication standard for industrial automation that was drawn up by the International Society of Automation (ISA). Outline, setup, settings, start-up, operation and maintenance of the entire field wireless system including the field wireless network and field wireless backbone are described in the User’s Manual of the YFGW410 field wireless management station (IM 01W02D01-01EN).

  • Page 11: Safety Precautions

    <Read Me First> Safety Precautions IMPORTANT Read the safety precautions for this product that are described in Read Me First (IM 01W02E01- 11EN). About Radio Wave IMPORTANT • This product is equipped with a wireless module which is designated as a certification of construction type as a wireless facility for 2.4 GHz band low-power data communication system of the Radio Act.
  • Page 12 <Read Me First> ■ FCC compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Co-Located: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
  • Page 13 <Read Me First> ■ Industry Canada (IC) compliance This Class A digital apparatus complies with Canadian ICES-003. French: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 14 <Read Me First> admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Antenna type: Gain: Sleeve 2.14dBi, 50Ω...

  • Page 15: Documentation Conventions

    <Read Me First> Documentation Conventions Typographical Convention The following typographical conventions are used throughout this document: Conventions commonly used throughout this document Character string to be entered The characters to be entered are shown in one-byte characters as follows: Example: FIC100.SV=50.0 “”Mark Indicates a space between character strings to be entered.

  • Page 16: Information Of Revision

    <Read Me First> Information of Revision Document Name: YFGW510 Field Wireless Access Point Document Number: IM 01W02D01-01EN Edition Date Page Revised Item August 2012 New Issue IM 01W02E01-01EN...

  • Page 17: Part-A. Overview Of Field Wireless System A1. Introduction

    A1-1 <A1. Introduction> PART-A. OVERVIEW OF FIELD WIRELESS SYSTEM A1. Introduction Read the User’s Manual of the YFGW410 field wireless management station (IM 01W02D01- 01EN) before reading this document. The YFGW510 field wireless access point is a core component of field wireless networks based on ISA100.11a, a wireless communication standard for industrial automation.

  • Page 18: A2. System Configuration

    A2-1 <A2. System Configuration> A2. System Configuration This section describes the configuration for the field wireless system including YFGW510. Host system Host system Field network Field network Field Wireless Field Wireless Management Station Management (YFGW410) Station (YFGW410) Field Wireless Field Wireless Management Management Console Console...
  • Page 19 A2-2 <A2. System Configuration> Field wireless management PC HIS/ENG Field Wireless Management Console NTP server Control network (Ethernet) Information network (Ethernet) Field network ALE111 x 2 Layer 3 switch Layer 2 switch Layer 2 switch Field Wireless Management Cable for redundancy Station (YFGW410) Layer 2 switch...

  • Page 20: Part-B. Functions Of Yfgw510 B1. Functions Of Yfgw510

    B1-1 <B1. Functions of YFGW510> PART-B. FUNCTIONS OF YFGW510 B1. Functions of YFGW510 The following block figures show communication functions of YFGW510 for each specification code. Communication function Communication function Internal clock Internal clock Backbone communication Initial communication Backbone communication Initial communication ISA communication IPv4/ARP/ICMP/IGMP...

  • Page 21: B2. Structure And Parts Of Yfgw510

    B2-1 <B2. Structure and Parts of YFGW510> B2. Structure and Parts of YFGW510 B2.1 Front View ISA100.11a antenna Wireless LAN antenna 1 Wireless LAN antenna 2 Tag plate for explosion protected type Status indicator LED (ACT, LAN, ISA) Wireless LAN status indicator (C1, C2, AP) Infrared port FB0201.ai...

  • Page 22: B2.2 Rear View

    B2-2 <B2. Structure and Parts of YFGW510> B2.2 Rear View Ground terminal RJ-45 connector ISA100.11a antenna Power supply terminal Wireless LAN antenna 1 Wireless LAN antenna 2 FB0202-1.ai 100BASE-TX/wireless LAN client specification IM 01W02E01-01EN...
  • Page 23 B2-3 <B2. Structure and Parts of YFGW510> ISA100.11a antenna Ground terminal SC connector Power supply terminal FB0202-2.ai 100BASE-FX specification Figure B2-2 Rear view of YFGW510 The power supply cable, grounding cable and field wireless backbone cable are connected on the back face of YFGW510. The electrical connection is provided on the bottom. In the 100BASE-FX specification, a media converter module is added to the 100BASE-TX speci- fication.

  • Page 24: B2.3 Side View

    B2-4 <B2. Structure and Parts of YFGW510> B2.3 Side View ISA100.11a antenna Main name plate FCC label Tag plate Wireless LAN Wireless LAN antenna 2 antenna 1 Electrical connection Electrical connection Ground terminal left side right side Tag plate for explosion protected type FB0203.ai Figure B2-3 Side view of YFGW510 The wireless LAN antenna connector(s) are equipped on the side(s) only for wireless LAN speci-...

  • Page 25: B3. Led Display Function

    B3-1 <B3. LED Display Function> B3. LED Display Function The functions of the status indicator LED on the front face are as fol- lows. Function Display the operating status of YFGW510 Display the operating status of the communication interface (100BASE-TX/100BASE-FX) ISA100 Display the operating status of ISA100.11a antenna Display the operating status of wireless LAN antenna 1...

  • Page 26: B4. Mechanical Operating Parts

    B4-1 <B4. Mechanical Operating Parts> B4. Mechanical Operating Parts YFGW510 does not have any switches or buttons that can be mechanically operated from out- side of the housing. IM 01W02E01-01EN...

  • Page 27: B5. Checking The Product

    B5-1 <B5. Checking the Product> B5. Checking the Product When you receive YFGW510, please check that the product specifications match your order, all items are included and that there is no damage, stains or other problems. Main unit Main name plate FIELD WIRELESS ACCESS POINT MODEL YFGW...

  • Page 28: Part-C. Installation

    C1-1 <C1. Installation Environment> PART-C. INSTALLATION This section describes installation for YFGW510. Follow the steps below to install YFGW510. Installation of YFGW510 Wiring of the power supply, grounding cable, signal cables and mounting/wiring of antenna(s) C1. Installation Environment YFGW510 should be installed in appropriate conditions to ensure its stable operation. The table below shows details of the installation environment for YFGW510.
  • Page 29 C1-2 <C1. Installation Environment> IMPORTANT This product is equipped with a wireless module which is designated as a certification of con- struction type as a wireless facility for 2.4 GHz band low-power data communication system of the Radio Act. Refer to G1.3 Regulatory Compliance Statements for detail. Before use, confirm that the location of installation satisfies the above standard.

  • Page 30: C2. Power Supply And Grounding

    C2-1 <C2. Power Supply and Grounding> C2. Power Supply and Grounding An appropriate power supply is necessary for the stable operation of YFGW510. C2.1 Power Supply Connect the power supply to the terminal block of the main unit. For details of the power supply and power consumption of YFGW510, see C1. Installation Environment. ALSO Inrush Current When starting up, inrush current may run into the device.

  • Page 31: C3. Requirements For Installation

    C3-1 <C3. Requirements for Installation> C3. Requirements for Installation C3.1 Requirements for Installation Locations The installation of YFGW510 and field wireless devices must meet the following conditions: • The field wireless equipment should be mounted in the place where no obstacle exists around the antenna.

  • Page 32: C3.2 Notes On Installation

    C3-2 <C3. Requirements for Installation> C3.2 Notes on Installation Pay attention to the following points at the installation of YFGW510 and field wireless devices. Installation Location This device is designed to work under the severe environmental condition. However, it is neces- sary to pay attention to the following conditions for the stable and long-term precise operation.

  • Page 33: C4. Mounting

    C4-1 <C4. Mounting> C4. Mounting Mount YFGW510 on the 2-inch (2B) pipe, placed vertically or horizontally, using the dedicated bracket. YFGW510 is accessed through its four or six sides. Make sure that the mounting pipe, the device, connectors or cables will not interfere with radio wave signals. This is achieved by us- ing the dedicated bracket.
  • Page 34 C4-2 <C4. Mounting> Mounting on vertical pipe (Communications interface: Wireless LAN client) FC0402.ai Figure C4-2 Mounting on vertical pipe (Communications interface: Wireless LAN client) When used for a single-line wireless LAN, YFGW510 is equipped only with the connector for wireless LAN antenna on the left side of the device. Assemble the bracket and attach YFGW510 to the bracket.
  • Page 35 C4-3 <C4. Mounting> Mounting on horizontal pipe (Communications interface: Wireless LAN client) FC0404.ai Figure C4-4 Mounting on horizontal pipe (Communications interface: Wireless LAN client) For use with a single-line wireless LAN, YFGW510 is equipped only with the connector for a wire- less LAN antenna on the left side of the device.

  • Page 36: C5. Wiring

    C5-1 <C5. Wiring> C5. Wiring This chapter describes connection of the power supply cable, grounding cable and network cable to the installed YFGW510, mounting of antennas and cable connection. • Use cables with a 70°C rating or higher for explosion-proof devices. •...
  • Page 37 C5-2 <C5. Wiring> l Power supply cable connection procedure Insert the power supply cable through the power supply cable gland into the housing. Screw the cable gland into the housing to fasten it. Connect the + cable to the + terminal and the – cable to the – terminal. For shielding the power supply cable, connect the grounding cable to the ground terminal next to the power terminal.

  • Page 38: C5.2 Grounding Cable Connection

    C5-3 <C5. Wiring> C5.2 Grounding Cable Connection This section describes ground wiring. Class D grounding (the third class grounding) with the grounding resistance of 100 Ω or less is necessary. To connect the grounding cable to YFGW510 directly, use the ground terminal on the right side of the main device.

  • Page 39: C5.3 Network Cable Connection

    C5-4 <C5. Wiring> C5.3 Network Cable Connection C5.3.1 Metal Network Cable Connection IMPORTANT: YFGW510 must be installed by professionals.  Caution for use with metal network cable The metal network cable is intended for indoor wiring. In outdoor wiring, it is recommended the optical network cable in order to eliminate the influence of electromagnetic noise due to lightning and keep transmission distance.

  • Page 40: C5.3.2

    C5-5 <C5. Wiring> RJ-45 connector Cable Gland for Communication Metal network cable FC0503.ai Figure C5-3 Connecting metal network cable C5.3.2 Optical Network Cable Connection l Cable Specification Item Optical network cable Standard 100BASE-FX Connector SC connector (1-pole × 2)* Multimode fiber (central wavelength: 1300 nm) Cable 50/125 µm or 62.5/125 µm The inner tension member must be nonmetal, such as FRP.
  • Page 41 C5-6 <C5. Wiring> l Optical network cable connection procedure Connect the optical network cable in the following procedure. Insert the optical network cable through the YFGW510 network cable gland. Insert the connector through the YFGW510 connection and screw in the cable gland. Connect the optical network cable to the SC connector of the device.

  • Page 42: C5.4 Installation And Wiring Of Antenna

    C5-7 <C5. Wiring> C5.4 Installation and wiring of Antenna This section describes mounting of antennas to YFGW510, and installation of external antennas and their wiring. C5.4.1 Mounting ISA100.11a antenna to YFGW510 This section explains the procedure for mounting the ISA100.11a antenna directly into the con- nector on top of the device.

  • Page 43: C5.4.2 Remote Installation And Wiring Of Isa100.11A Antenna

    C5-8 <C5. Wiring> l Tape • Butyl rubber self-bonding tape • Vinyl tape or a vinyl type self-bonding tape Antenna FC0506.ai Figure C5-6 Sealing of antenna connector IMPORTANT The ISA100.11a antenna connector for the YFGW510 supports 2-dBi standard antennas only. A high-gain antenna, available as an optional accessory, must be installed as a remote antenna with an antenna extension cable, as described in the next section.
  • Page 44 C5-9 <C5. Wiring> ISA100.11a antenna 2-inch pipe 2-inch pipe Bracket ISA100.11a antenna U Bolt Antenna Extension Cable Washer Bracket 2 Antenna Extension Cable Bracket 1 Nut and Washer FC0507.ai Figure C5-7 Fastening external antenna Mounting procedure of antenna Fix the antenna extension cable to the bracket 1 with the provided nut as shown in the figure above.
  • Page 45 C5-10 <C5. Wiring> l Wiring of extension antenna cable Use the provided extension antenna cable to connect the antenna connector with the ex- ternal antenna. Tighten the connector of the antenna extension cable with a torque of 2 to 3 N∙m.
  • Page 46 C5-11 <C5. Wiring> l Grounding cable (Insulated for industrial equipment) Examples • 600 V polyvinyl chloride insulated wires (IV): JIS C3307 • Polyvinyl chloride insulated wires for electrical apparatus (KIV): JIS C3316 • 600 V grade heat-resistant polyvinyl chloride insulated wires (HIV): JIS C3317 •...

  • Page 47: C5.4.3 Installation And Wiring Of Wireless Lan Antenna

    C5-12 <C5. Wiring> l Waterproofing antenna cables and connectors Make sure that the antenna, extension cables and arrestor wring including the grounding cable are connected properly. Protect the connectors and the arrestor with tape. As described in C5.4.1 Mounting ISA100.11a Antenna to YFGW510, wind self-bonding tape and vinyl tape around con- nections.
  • Page 48 C5-13 <C5. Wiring> • WLAN specification (single communications) Wireless LAN antenna Spring washer U Bolt Vertical piping Bracket x2 Angle bracket FC0511-2.ai Extension Cable FC0511-1.ai Wireless LAN antenna U Bolt Horizontal piping Bracket x2 Angle bracket FC051.ai FC0511-4.ai Figure C5-11 Connecting brackets to fasten the wireless LAN specification antenna IM 01W02E01-01EN...
  • Page 49 C5-14 <C5. Wiring> ・ WLAN specification (redundant communications) YFGW510 does not transmit at the same time from any antenna. Figure C5-12 Connecting brackets to fasten the WLAN redundant specification antenna  Wireless LAN antenna fastening procedure  Fix the antenna extension cable to the bracket 1 with the provided nut as shown in the figure above.
  • Page 50 C5-15 <C5. Wiring> Wiring of wireless LAN antenna and improvement of environmental ■ resistance  Specification of extension cable for wireless LAN antenna (Use only the cables included as option.) • Specification: 8D-SFA(PE) • Outside Diameter: 11.1 mm • Minimum Bend Radius: 67 mm (when fixing) 167 mm (when wiring) •...
  • Page 51 C5-16 <C5. Wiring> YFGW510 does not transmit at the same time from any antenna. Figure C5-14 Wiring of wireless LAN antenna (redundant communications)  Ground wiring of arrestor Place an arrestor between two extension cables. Connect the grounding cable to the ground terminal of the arrestor.
  • Page 52 C5-17 <C5. Wiring> Antenna External antenna cable 2 Grounding cable wiring Arrestor External antenna cable 1 YFGW510 FC0515.ai Figure C5-15 Wiring for arrestor l Waterproofing antenna cables and connectors Make sure that the antenna, extension cables and arrestor wring including the grounding cable are connected properly.

  • Page 53: C6. Explosion Proof Wiring

    C6-1 <C6. Explosion Proof Wiring> C6. Explosion Proof Wiring - Explosion proof approval is pending - Remainder of page intentionally left blank IM 01W02E01-01EN...

  • Page 54: D1. Initial Configuration

    D1-1 <D1. Initial Configuration> PART-D. SETUP D1. Initial Configuration Initial configuration is required to connect YFGW510 to YFGW410. To set the initial configuration, install the field wireless access point setup tool (setup tool) pro- vided with YFGW510 on a PC and connect the infrared adapter of the PC to YFGW510. The table below shows the essential items to set in the initial configuration.

  • Page 55: D2. Setup Tool

    D2-1 <D2. Setup Tool> D2. Setup Tool This chapter provides system requirements and installation procedures for the field wireless ac- cess point setup tool. D2.1 System Requirements Basic license of software provided with YFGW510: 1 licensee Language: Software (GUI): English User’s manual: Japanese or English (to be specified at the time of order) D2.1.1 Hardware...

  • Page 56: D2.1.3 Connection Example

    D2-2 <D2. Setup Tool> D2.1.3 Connection Example To use the setup tool, infrared communication between the PC and YFGW510 is required. Connect the Infrared adapter to a USB port on the PC. Place the Infrared adapter close to the infrared photoreceiver of YFGW510 and ensure that they face each other. For distance between YFGW510 and the Infrared adapter, see the table below.

  • Page 57: D2.2 Installation Procedure

    D2-3 <D2. Setup Tool> D2.2 Installation Procedure Install the field wireless access point setup tool and Infrared adapter driver on the PC. D2.2.1 Driver for Infrared adapter Installing the driver Install the driver by the means provided with the Infrared adapter, referring to the user’s manual of ACTiSYS Checking the device Connect the Infrared adapter to a USB port on the PC.

  • Page 58: D2.2.2 Field Wireless Access Point Setup Tool

    D2-4 <D2. Setup Tool> D2.2.2 Field Wireless Access Point Setup Tool Installation Insert the DVD, provided along with YFGW510, into the PC. Copy the folder containing the setup tool program (YFGW510Tool.exe and FWMCCommon.dll) into a folder on the PC hard drive. This program will not change the registry information of Windows.
  • Page 59 D2-5 <D2. Setup Tool> The table below shows the setting items and their default settings. Item Number of characters Default setting The number of the port the Infra- The smallest COM number Serial Port red adapter is connected to among those devices Up to 8 one-byte alphanumeric Login Password characters or other symbols...
  • Page 60 D2-6 <D2. Setup Tool> Check the adapter COM port number, and positions in the front window of YFGW510. After the problem has been solved, click the [OK] button. The window will close. Go back to the window as shown in Figure D2-3. Check the entered information and click the [OK] button to proceed.
  • Page 61 D2-7 <D2. Setup Tool> FD0206.ai Figure D2-6 Main window The Backbone Interface tab of the setup tool’s main window is always shown at startup of the set- up tool. The window is also shown in Display mode with the parameter fields and buttons grayed out.

  • Page 62: D3. Configuration Method

    D3-1 <D3. Configuration Method> D3. Configuration Method This section describes initial configuration of YFGW510 using the field wireless access point setup tool. D3.1 Window Design The main window of the field wireless access point setup tool consists of the following seven tabs.

  • Page 63: D3.2 Display/Edit Mode Switching

    D3-2 <D3. Configuration Method> D3.2 Display/Edit Mode Switching The field wireless access point setup tool has two operation modes: Display, to view the setting information, and Edit, to configure YFGW510. The setup tool always starts up in Display mode. To allow for YFGW510 configuration, the mode needs to be switched to Edit. To change modes, select the [Maintenance] tab as shown in Figure D3-1.
  • Page 64 D3-3 <D3. Configuration Method> FD0302.ai Figure D3-2 Setup mode change confirmation dialog box Clicking the [OK] button navigates to the login window shown in Figure D2-3. Log in again and setup will start up in Edit mode. Clicking the [Cancel] button terminates the mode switching. Setup starts up in Display mode even if the mode was Edit at the last logoff;...

  • Page 65: D3.3 Backbone Interface

    D3-4 <D3. Configuration Method> D3.3 Backbone Interface The [Backbone Interface] tab allows a change in settings for the YFGW510 connection to the field wireless backbone network. Figure D3-3 shows the [Backbone Interface] tab in Edit mode. FD0303.ai Figure D3-3 Backbone Interface tab The following are items that need to be set inYFGW510.
  • Page 66 D3-5 <D3. Configuration Method> Password setting regulation The password for the connection to YFGW410 on the Field Wireless Access Point has the follow- ing restrictions. No string outside of these restrictions can be accepted. • Up to sixteen characters • From “A” to “F” and numeric characters only (case sensitive) After entering all required items, click the [Save] button to store settings in YFGW510.

  • Page 67: D3.4 Maintenance

    D3-6 <D3. Configuration Method> D3.4 Maintenance Clicking the [Maintenance] tab displays the controls shown in Figure D3-4. FD0304.ai Figure D3-4 The following describes the functions of the buttons on this tab. Button Name Function Clicking the button switches Display/Edit mode for the setup tool. For details, Display Mode/Edit Mode see D3.2 Display/Edit Mode Switching.
  • Page 68 D3-7 <D3. Configuration Method> FD0305.ai Figure D3-5 YFGW510 Restart confirmation dialog box Clicking the [OK] button restarts YFGW510 and navigates to the login window shown in Figure D2-3. Clicking the [Cancel] button terminates the process and closes the confirmation dialog box. IM 01W02E01-01EN...

  • Page 69: D3.5 Setting Of Wireless Lan 1 (Wlan C1)

    D3-8 <D3. Configuration Method> D3.5 Setting of Wireless LAN 1 (WLAN C1) Clicking the [WLAN C1] tab displays the controls and information shown in Figure D3-6. FD0306.ai Figure D3-6 WLAN C1 tab This tab allows the setting of wireless LAN 1. The setting items are as follows.
  • Page 70 D3-9 <D3. Configuration Method>  Network key setting The network key to be set for the Field Wireless Access Point has the following restrictions: • Up to 31 characters • Single-byte alphanumeric characters and other marks and signs (e.g., “!”, “$”, “#”) ...

  • Page 71: D3.6 Setting Of Wireless Lan 2 (Wlan C2)

    D3-10 <D3. Configuration Method> D3.6 Setting of Wireless LAN 2 (WLAN C2) Clicking the [WLAN C2] tab displays the controls and information shown in Figure D3-7. FD0307.ai Figure D3-7 WLAN C2 tab This tab allows the settings for wireless LAN 2. The procedure for setting items is the same as for the wireless LAN 1.

  • Page 72: D3.7 Setting Of Wlan Redundancy

    D3-11 <D3. Configuration Method> D3.7 Setting of WLAN Redundancy Clicking the [WLAN Redundancy] tab displays the controls shown in Figure D3-8. FD0308.ai Figure D3-8 WLAN Redundancy tab This tab allows the setting for wireless LAN redundancy. The setting items are as follows. Item Descriptions Initial Value...

  • Page 73: D3.8 Version Information

    D3-12 <D3. Configuration Method> D3.8 Version Information Clicking the [Version Information] tab displays the information shown in Figure D3-9. FD0309.ai Figure D3-9 Version Information tab This tab displays information about the YFGW510 Field Wireless Access Point, such as the ven- dor name, model name and firmware versions.

  • Page 74: Part-E. Operation And Maintenance

    E1-1 <E1. Routine Maintenance> PART-E. OPERATION AND MAINTENANCE For information about routine maintenance, or for YFGW510 additions or replacements, consult, in advance, the YFGW410 User’s Manual (IM 01W02D01-01EN). E1. Routine Maintenance For problems during routine maintenance, check the host system monitoring YFG510, and the device information for the Field Wireless Management Console monitor provided with the YFGW410.

  • Page 75: E2. Additions And Replacements

    E2-1 <E2. Additions and Replacements> E2. Additions and Replacements For instructions on adding or replacing YFGW510, see the YFGW410 User’s Manual (IM 01W02D01-01EN). IM 01W02E01-01EN...

  • Page 76: E3. Maintenance In Hazardous Areas

    E3-1 <E3. Maintenance in Hazardous Areas> E3. Maintenance in Hazardous Areas In maintenance, check for loose power supply wiring, ground wiring or network cable connection. During maintenance and repair activities, if there is need to access the system in hazardous areas via an YFGW510 communication port, PCs and other devices used must comply with the explosion-proof requirements.

  • Page 77: E4. Components Having Defined Life Spans

    E4-1 <E4. Components Having Defined Life Spans> E4. Components Having Defined Life Spans YFGW510 includes no components having defined life spans that need replacing. For reference, the following are precautions for such components. IMPORTANT Precautions for components having defined life spans •...
  • Page 78 F1-1 <F1. Status Information> PART-F. TROUBLESHOOTING This section describes troubleshooting for YFGW510. If any abnormalities are identified in YFGW510 through investigation and in accordance with procedures described in the YFGW410 User’s Manual (IM 01W02D01-01EN), check the following. Status Information The YFGW510 operational status information is shown in the backbone router status (BBR_STA- TUS) in the Modbus register.
  • Page 79 F2-1 <F2. Status Indication and Responsive Measures> Status Indication and Responsive Measures There are six status indicator LEDs installed on the front of YFGW510: [ACT], [LAN], [ISA100], [WLAN-C1], [WLAN-C2] and [WLAN-AP]. YFGW510 operational status indication The following is the LED that indicates the YFGW510 operational status. Connect- Mainte- Power off...
  • Page 80 F2-2 <F2. Status Indication and Responsive Measures> [ISA100] LED If the LED turns off during operation, it may indicate that communication between YFGW510 and all field wireless network devices has been terminated. Investigate the connection of the ISA100.11a antenna and the condition of the antenna extension cables, and re-establish com- munication.

  • Page 81: Part-G. Specifications

    G1-1 <G1. Standard Specifications> PART-G. SPECIFICATIONS G1. Standard Specifications G1.1 Communication Interface Specifications Field Network Item Field Wireless Backbone Specifications Specifications Communication Standard IEEE802.15.4 IEEE802.11a/b/g 100BASE-TX 100BASE-FX Interface Frequency 2400–2483.5MHz b/g: 2400-2483.5MHz – a: 5150-5850MHz Raw data rate 250kbps 1~54Mbps 100Mbps 100Mbps Radio Security...

  • Page 82: G1.2 General Specifications

    G1-2 <G1. Standard Specifications> G1.2 General Specifications Performance Physical Specifications Network Size: Connections: Max 100 field wireless devices are connectable Refer to “MODEL AND SUFFIX CODES.” Display: Housing Material: 2-color luminescence LED displays the Low copper cast aluminum alloy with operating state of this product, and the Polyurethane, mint-green paint (Munsell 5.6BG operating state of wireless communications and...

  • Page 83: G1.3 Regulatory Compliance Statements

    G1-3 <G1. Standard Specifications> G1.3 Regulatory Compliance Statements Regulatory Compliance State- ments This device contains the wireless module. The wireless module satisfies the following standards. The specific radio equipment (Approval Number: ISA100.11a: 007-AA00110,Wireless LAN: 007- AA0065/66) which received the technical standard satisfied certification based on the Radio Law is used for this product.

  • Page 84: G2. Model, Suffix Codes And Option Codes

    G2-1 <G2. Model, Suffix Codes and Option Codes> G2. Model, Suffix Codes and Option Codes Model Suffix Codes Description YFGW510  Field Wireless Access Point Output -A  ISA100.11a signal -C  ISA100.11a, IEEE802.11a/b/g Communication 1  100 BASE-TX interface 2  100 BASE-FX 5  Wireless LAN Housing...
  • Page 85 G2-2 <G2. Model, Suffix Codes and Option Codes> OPTIONAL SPECIFICATION (For Explosion Protected type) Item Description Code TIIS Certification Flameproof Approval – Factory Mutual (FM) Nonincendive, Explosionproof Approval – ATEX Type n Declaration, Flameproof Approval – Canadian Standards Association (CSA) Nonincendive, Flameproof Approval –...

  • Page 86: G3. External Dimensions

    G3-1 <G3. External Dimensions> G3. External Dimensions G3.1 100BASE-TX/100BASE-FX Specifications Vertical pipe mounting Unit ： mm 2-inch pipe FG0301.ai IM 01W02E01-01EN...
  • Page 87 G3-2 <G3. External Dimensions> Horizontal pipe mounting Unit ： mm Graund terminal 2-inch pipe FG0302.ai IM 01W02E01-01EN...

  • Page 88: G3.2 Single Communication Wireless Lan Client Specifications

    G3-3 <G3. External Dimensions> G3.2 Single Communication Wireless LAN Client Specifications Vertical pipe mounting Unit ： mm 2-inch pipe FG0303.ai IM 01W02E01-01EN...
  • Page 89 G3-4 <G3. External Dimensions> Horizontal pipe mounting Unit ： mm Graund 2-inch pipe terminal FG0304.ai IM 01W02E01-01EN...

  • Page 90: G3.3 Redundant Communication Wireless Lan Client Specifications

    G3-5 <G3. External Dimensions> G3.3 Redundant Communication Wireless LAN Client Specifications Vertical pipe mounting Unit ： mm 2-inch pipe FG0305.ai IM 01W02E01-01EN...
  • Page 91 G3-6 <G3. External Dimensions> Horizontal pipe mounting Unit ： mm Graund 2-inch pipe terminal FG0306.ai IM 01W02E01-01EN...

This manual is also suitable for:

Yfgw510

Table of Contents