Related Manuals for Analog Devices EZ-Extender ADSP-CM408 Series
Summary of Contents for Analog Devices EZ-Extender ADSP-CM408 Series
- Page 1 Analog 120-Pin Probing Board Manual ® an EZ-Extender product Revision 1.0, September 2013 Part Number 82-000388-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106...
- Page 2 Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use;...
- Page 3 Regulatory Compliance The Analog 120-Pin Probing Board is designed to be used solely in a labo- ratory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity.
-
Page 5: Table Of Contents
Manual Contents ................ix What’s New in This Manual ............ix Technical Support ................x Supported Products ................x Product Information ............... xi Analog Devices Web Site ............xi EngineerZone ................xii Notation Conventions ..............xii Analog 120-Pin Probing Board Manual... - Page 6 Contents USING ANALOG 120-PIN PROBING BOARD Package Contents ................. 1-1 Analog 120-Pin Probing Board Installation ........1-2 Expansion Interface ..............1-3 Reference Design Information ............1-4 ANALOG 120-PIN PROBING BOARD HARDWARE REFERENCE System Architecture ..............2-1 Connectors ................... 2-2 Connector (J1) ............... 2-3 Connector (P1) ...............
-
Page 7: Product Overview
PREFACE Thank you for purchasing the Analog 120-Pin Probing Board, Analog Devices, Inc. probing board for the ADSP-CM40x family of mixed-signal control processors. The ADSP-CM408F mixed-signal control processor is based on the ® ® Cortex -M4 processor core and is designed for motor control and industrial applications. -
Page 8: Purpose Of This Manual
Purpose of This Manual • Four probing headers • Samtec TSW-115-07-L-D • Eight GND headers • FCI 90726-402HLF For information about the hardware components of the product, refer to Analog 120-Pin Probing Board Bill Of Materials. Purpose of This Manual The Analog 120-Pin Probing Board Manual provides instructions for installing the product hardware (board). -
Page 9: Manual Contents
Preface For additional information on this Analog Devices processor, see the ADSP-CM40x Mixed-Signal Control Processor Hardware Reference. This document describes the ARM Cortex-M4 processor core and memory architecture used on the ADSP-CM40x processor, but does not provide detailed programming information for the ARM core. -
Page 10: Technical Support
Technical Support Technical Support You can reach Analog Devices processors and DSP technical support in the following ways: • Post your questions in the processors and DSP support community ® at EngineerZone http://ez.analog.com/community/dsp • Submit your questions to technical support directly at: http://www.analog.com/support... -
Page 11: Product Information
Preface Product Information Product information can be obtained from the Analog Devices Web site and the online help system. Analog Devices Web Site The Analog Devices Web site, , provides information www.analog.com about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors. -
Page 12: Engineerzone
Notation Conventions EngineerZone EngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions. - Page 13 Preface Example Description Note: For correct operation, ... A Note provides supplementary information on a related topic. In the online version of this book, the word Note appears instead of this symbol. Caution: Incorrect device operation may result if ... ...
- Page 14 Notation Conventions Analog 120-Pin Probing Board Manual...
-
Page 15: Using Analog 120-Pin Probing Board
1 USING ANALOG 120-PIN PROBING BOARD This chapter provides information about using the Analog 120-Pin Prob- ing Board. The following topics are covered. • Package Contents • Analog 120-Pin Probing Board Installation • Expansion Interface • Reference Design Information For detailed information on how to program the ADSP-CM40x proces- sors, refer to the documents listed in the Preface. -
Page 16: Analog 120-Pin Probing Board Installation
Analog 120-Pin Probing Board Installation Contact the vendor where you purchased your EZ-KIT Lite or contact Analog Devices, Inc. if any item is missing. Analog 120-Pin Probing Board Installation Follow these instructions to ensure correct operation of the product hardware. -
Page 17: Expansion Interface
There is also a 120-pin connector for Analog signals. The Analog 120-Pin Probing Board should not be connected to the 180-pin connectors. Analog Devices does not support and is not responsible for the effects of additional circuitry. Analog 120-Pin Probing Board Manual... -
Page 18: Reference Design Information
Reference Design Information Reference Design Information A reference design info package is available for download on the Analog Devices Web site. The package provides information on the design, lay- out, fabrication, and assembly of the probing board. The information can be found at: http://www.analog.com/MCEI1-AnalogProbingBoard Analog 120-Pin Probing Board Manual... -
Page 19: Analog 120-Pin Probing Board Hardware Reference
2 ANALOG 120-PIN PROBING BOARD HARDWARE REFERENCE This chapter describes the hardware design of the Analog 120-Pin Probing Board. The following topics are covered. • System Architecture Describes the board’s configuration and explains how the board components interface with the processor. •... -
Page 20: Connectors
Connectors Connectors This section describes connector functionality and provides information about mating connectors. The connector locations are shown in Figure 2-1. Figure 2-1. Connector Locations Analog 120-Pin Probing Board Manual... -
Page 21: Connector (J1)
Analog 120-Pin Probing Board Hardware Reference Connector (J1) Part Description Manufacturer Part Number 120-pin high speed socket SAMTEC QSH-060-01-F-D-A Mating Connector 120-pin high speed header SAMTEC QTH-060-01-F-D-A Connector (P1) Part Description Manufacturer Part Number 120-pin high speed header SAMTEC QTH-060-01-F-D-A Mating Connector 120-pin high speed socket SAMTEC... - Page 22 Connectors Analog 120-Pin Probing Board Manual...
- Page 23 A ANALOG 120-PIN PROBING BOARD BILL OF MATERIALS The bill of materials corresponds to Analog 120-Pin Probing Board Schematic. Ref. Qty Description Reference Manufacturer Part Number Designator IDC 2X1 IDC2X1 P7-P14 90726-402HLF 0.5MM 120PIN SAMTEC_ SAMTEC QSH-060-01-F-D-A QSH-060-F-D-A 0.5MM 120PIN SAMTEC_ SAMTEC QTH-060-01-F-D-A QTH-060-F-D-A...
- Page 24 Analog 120-Pin Probing Board Manual...
- Page 25 ANALOG 12...
- Page 26 PIN_34 PIN_33 PIN_38 PIN_37 PIN_29 PIN_42 PIN_41 PIN_46 PIN_45 PIN_50 PIN_49 AGND PIN_54 PIN_53 PIN_58 PIN_57 PIN_60 PIN_59 PIN_61 PIN_62 PIN_61 PIN_63 PIN_64 PIN_63 PIN_66 PIN_65 PIN_65 PIN_68 PIN_67 PIN_70 PIN_69 PIN_67 PIN_72 PIN_71 PIN_74 PIN_73 PIN_69 PIN_76 PIN_75 PIN_78 PIN_77 PIN_71 PIN_80...
- Page 27 INDEX architecture, of this probing board, notation conventions, bill of materials, P1 connector, board installation, P2-P5 connector, mechanical mating details, P7-P14 connector, board schematic, package contents, product overview, connector (J1), connectors, reference design information, diagram of locations, schematic of board, P2-P5, system architecture, of this probing board, P7-P14,...
- Page 28 Index Analog 120-Pin Probing Board Manual...
- Page 29 Daughter Cards & OEM Boards Click to view products by manufacturer: Analog Devices Other Similar products are found below : ADZS-21262-1-EZEXT 27911 MPC5777C-416DS KITMPC5744DBEVM SPC56ELADPT144S TMDXRM46CNCD DM160216 EV- ADUCM350GPIOTHZ EV-ADUCM350-BIO3Z ATSTK521 1130 MA160015 MA240013 MA240026 MA320014 MA330014 MA330017 TMDSCNCD28054MISO MIKROE-2152 MIKROE-2154 MIKROE-2381 TSSOP20EV MIKROE-1108 MIKROE-1516 SPS-READER-...
Need help?
Do you have a question about the EZ-Extender ADSP-CM408 Series and is the answer not in the manual?
Questions and answers