[Status] - Panasonic PT-RQ35KU Operating Instructions Manual

[SUB MEMORY]
[SYSTEM SELECTOR]
[SYSTEM DAYLIGHT VIEW]
[FREEZE]
[WAVEFORM MONITOR]
[LENS MEMORY LOAD]
[PROJECTION METHOD]
4) Press the <ENTER> button.

[STATUS]

Display the status of the projector.
1) Press as to select [STATUS].
2) Press the <ENTER> button.
f The [STATUS] screen is displayed.
3) Press qw to switch the pages.
f The page will change each time you press the button.
[PROJECTOR TYPE]
[PROJECTOR RUNTIME]
[LIGHT RUNTIME]
[MAIN/SUB VERSION]
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[EXHAUST AIR TEMP.]
[LIGHT1-B TEMP.]
[LIGHT1-S TEMP.]
[LIGHT2-B TEMP.]
[LIGHT2-S TEMP.]
[SELF TEST]
[INPUT]
[SIGNAL NAME]
[MEMORY NO.]
[BACKUP INPUT STATUS]
[NUMBER OF REGISTERED
SIGNAL]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS]
[AC VOLTAGE]
[LENS TYPE]
*2
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the sub memory list. (x page 188)
Switches the [SYSTEM SELECTOR] setting according to the input signal of the image being
projected.
f When the input is SDI1 to SDI4 equipped on this projector as the standard projector.
g The [DISPLAY OPTION] menu → [SDI IN] → [SINGLE LINK SETTING] → [SDI1]/[SDI2]/[SDI3]/
[SDI4] → [SYSTEM SELECTOR]
g The [DISPLAY OPTION] menu → [SDI IN] → [DUAL LINK SETTING] → [SDI1-2]/[SDI3-4] →
[SYSTEM SELECTOR]
g The [DISPLAY OPTION] menu → [SDI IN] → [QUAD LINK SETTING] → [SYSTEM SELECTOR]
f When the input is SDI1 to SDI4 on the Interface Board
g The [DISPLAY OPTION] menu → [SLOT IN] → [SINGLE LINK SETTING] → [SDI1 [SLOT1]]/
[SDI2 [SLOT1]]/[SDI3 [SLOT2]]/[SDI4 [SLOT2]] → [SYSTEM SELECTOR]
g The [DISPLAY OPTION] menu → [SLOT IN] → [DUAL LINK SETTING] → [SYSTEM
SELECTOR]
g The [DISPLAY OPTION] menu → [SLOT IN] → [QUAD LINK SETTING] → [SYSTEM
SELECTOR]
f When the input is anything other than SDI
The [PICTURE] menu → [SYSTEM SELECTOR]
Switches the [SYSTEM DAYLIGHT VIEW] setting. (x page 97)
Temporarily pauses the image. (x page 145)
Displays the waveform of the input signal. (x page 145)
Loads the registered lens memory. (x page 151)
Switches the [PROJECTION METHOD] setting. (x page 148)
Displays the projector type and serial number of the projector.
Displays the runtime of the projector.
Displays the runtime of the light source 1 and the light source 2.
Displays the main and sub versions of the firmware of the projector.
Displays the status of the intake air temperature of the projector.
*1
Displays the status of the internal temperature of the projector.
*1
Displays the status of the exhaust air temperature of the projector.
*1
*1
Displays the light source 1 temperature status of the projector.
*1
*1
Displays the light source 2 temperature status of the projector.
*1
Displays the status of the projector.
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
Displays the input signal name.
Displays the memory number of the input signal.
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 117)
Displays the number of registered signals.
Displays the set cooling conditions.
Displays the control status of the REMOTE2.
Displays the input supply voltage.
Displays the type name (type of the projection lens) set to the projection lens.
ENGLISH - 177