Panasonic PT-RQ35KU Operating Instructions Manual page 172

[COMMAND]
[POWER ON]
[STANDBY]
[SHUTTER]
[INPUT]
[OPERATING MODE]
[MULTI DISPLAY]
*1 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>.
*4 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 2>.
*5 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*6 If you change the settings while using the projector, the duration until the light source luminance decreases by half may shorten or the
luminance may decrease.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
172 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[OPEN]
[CLOSE]
[SDI1]
[SDI2]
[SDI3]
[SDI4]
[DIGITAL LINK]
[HDMI1 [SLOT1]]
[HDMI2 [SLOT1]]
[HDMI3 [SLOT2]]
[HDMI4 [SLOT2]]
[DVI-D1 [SLOT1]]
[DVI-D2 [SLOT1]]
[DVI-D3 [SLOT2]]
[DVI-D4 [SLOT2]]
[DisplayPort1 [SLOT1]]
[DisplayPort2 [SLOT1]]
[DisplayPort3 [SLOT2]]
[DisplayPort4 [SLOT2]]
[SDI1 [SLOT1]]
*1
[SDI2 [SLOT1]]
*1
[SDI3 [SLOT1]]
*3
[SDI4 [SLOT1]]
*3
[SDI1 [SLOT2]]
*4
[SDI2 [SLOT2]]
*4
[SDI3 [SLOT2]]
*2
[SDI4 [SLOT2]]
*2
[INPUT1] - [INPUT10]
[HIGH]
[NORMAL]
[LONG LIFE1]
[LONG LIFE2]
*6
[LONG LIFE3]
[USER1]
[USER2]
[USER3]
[OFF]
[USER1]
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Disables the shutter function (shutter: open).
Enables the shutter function (shutter: closed).
Switches the input to SDI1.
Switches the input to SDI2.
Switches the input to SDI3.
Switches the input to SDI4.
Switches the input to DIGITAL LINK.
Switches the input to HDMI1 of the Interface Board.
*1
Switches the input to HDMI2 of the Interface Board.
*1
Switches the input to HDMI3 of the Interface Board.
*2
Switches the input to HDMI4 of the Interface Board.
*2
Switches the input to DVI-D1 of the Interface Board.
*1
Switches the input to DVI-D2 of the Interface Board.
*1
Switches the input to DVI-D3 of the Interface Board.
*2
Switches the input to DVI-D4 of the Interface Board.
*2
Switches the input to DisplayPort1 of the Interface Board.
*1
Switches the input to DisplayPort2 of the Interface Board.
*1
Switches the input to DisplayPort3 of the Interface Board.
*2
Switches the input to DisplayPort4 of the Interface Board.
*2
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to DIGITAL LINK, and switches the input of the
*5
Panasonic twisted-pair-cable transmitter to the specified input.
The life of the light source shortens compared to [NORMAL], but the
luminance increases more than [NORMAL].
Prioritizes luminance. (Factory default setting)
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
Controls the power to increase the life of the light source although
the luminance is even lower than that of [LONG LIFE1].
Controls the power to increase the life of the light source to the
maximum although the luminance is even lower than that of [LONG
LIFE2].
Controls the power with the setting set to [USER1].
Controls the power with the setting set to [USER2].
Controls the power with the setting set to [USER3].
Does not use the multi-display function.
Displays four-screen display with the setting in [USER1].
Displays four-screen display with the setting in [USER2].
Displays four-screen display with the setting in [USER3].
Description