Sirius Satellite Radio S-DDH1 Use And Maintenance Instruction page 54

INSTALLATION PROCEDURE INSTALLATION PROCEDURE
• The worktop must be perfectly level. • The worktop must be perfectly level.
• Place the cooking hob into the previously real-
ised opening in the worktop.
• Press the cooking hob down forcefully onto
the worktop, in correspondence to the edges
of the cooking hob.
If the downdraft is not perfectly aligned with the
cooking hob, adjust the adjustment screws (Fig.
10A) on the right and left of the product. Screw
in the screws to lift the downdraft and unscrew
to lower the downdraft.
INSTALLATION PROCEDURE
• Place the cooking hob into the previously real- • Place the cooking hob into the previously real-
Before the installation, the screws indicated in ised opening in the worktop. ised opening in the worktop.
Fig. 10B must be unscrewed as much as pos-
• Press the cooking hob down forcefully onto • Press the cooking hob down forcefully onto
• The worktop must be perfectly level.
sible so as to keep the downdraft near to the rear the worktop, in correspondence to the edges the worktop, in correspondence to the edges
part of the kitchen unit. of the cooking hob. of the cooking hob.
If the downdraft is not centred correctly with the
cooking hob after the installation has been car-
If the downdraft is not perfectly aligned with the If the downdraft is not perfectly aligned with the
ried out, utilise the adjustment screws (Fig. 10B)
cooking hob, adjust the adjustment screws (Fig. cooking hob, adjust the adjustment screws (Fig.
10A) on the right and left of the product. Screw 10A) on the right and left of the product. Screw
to shift it forwards by screwing in the screws or
backwards by unscrewing the screws on both
in the screws to lift the downdraft and unscrew in the screws to lift the downdraft and unscrew
the right and left side of the product.
to lower the downdraft. to lower the downdraft.
1. Check that the downdraft inside the kitchen Before the installation, the screws indicated in
Before the installation, the screws indicated in
Fig. 10B must be unscrewed as much as pos- Fig. 10B must be unscrewed as much as pos-
unit is perfectly vertical. Fix it utilising the
brackets supplied (Fig. 11).
sible so as to keep the downdraft near to the rear
sible so as to keep the downdraft near to the rear
2. Permanently block the downdraft utilising the part of the kitchen unit. part of the kitchen unit.
two screws indicated in Fig. 12.
If the downdraft is not centred correctly with the If the downdraft is not centred correctly with the
3. Connect the electrical cables of the down- cooking hob after the installation has been car- cooking hob after the installation has been car-
ried out, utilise the adjustment screws (Fig. 10B) draft as shown in Fig. 13 and then carry out
ried out, utilise the adjustment screws (Fig. 10B)
• Place the cooking hob into the previously real-
to shift it forwards by screwing in the screws or to shift it forwards by screwing in the screws or the connection to the mains electricity in ac-
ised opening in the worktop.
backwards by unscrewing the screws on both backwards by unscrewing the screws on both
• Press the cooking hob down forcefully onto
the right and left side of the product. the right and left side of the product.
the worktop, in correspondence to the edges
52
of the cooking hob.
1. Check that the downdraft inside the kitchen 1. Check that the downdraft inside the kitchen
unit is perfectly vertical. Fix it utilising the unit is perfectly vertical. Fix it utilising the
If the downdraft is not perfectly aligned with the
brackets supplied (Fig. 11). brackets supplied (Fig. 11).
cooking hob, adjust the adjustment screws (Fig.
2. Permanently block the downdraft utilising the 2. Permanently block the downdraft utilising the 10A) on the right and left of the product. Screw
two screws indicated in Fig. 12. two screws indicated in Fig. 12.
in the screws to lift the downdraft and unscrew
3. Connect the electrical cables of the down-
3. Connect the electrical cables of the down-
to lower the downdraft.
draft as shown in Fig. 13 and then carry out draft as shown in Fig. 13 and then carry out
the connection to the mains electricity in ac-
the connection to the mains electricity in ac-
Before the installation, the screws indicated in
Fig. 10B must be unscrewed as much as pos-
sible so as to keep the downdraft near to the rear
52 52
part of the kitchen unit.
If the downdraft is not centred correctly with the
lifting of the extraction carriage by pressing
EN EN
the key.
5. When the extraction carriage is fully opened,
remove the door block (Fig. 14). Successive-
ly open the door (Fig. 15) and position the
cordance with the information reported on cordance with the information reported on
anti-grease filters (Fig. 16).
the relative technical data plate.
the relative technical data plate.
4. After completing the installation and having
4. After completing the installation and having
6. The motor can be installed on the front or
connected the downdraft to the mains elec-
connected the downdraft to the mains elec-
rear part of the downdraft. The air outlet must
tricity, check that the red key on the electron- tricity, check that the red key on the electron-
be pointed upwards or downwards.
ic metal box is pressed and then activa ic metal box is pressed and then activate the
7. Assemble the ducting for the air outlet.
lifting of the extraction carriage by pressing lifting of the extraction carriage by pressing
8. In the case of the version with an external
motor, choose the air outlet most suitable
from the five possibilities (refer to the design
the the key. key.
in the TECHNICAL ILLUSTRATION chapter)
5. When the extraction carriage is fully opened, 5. When the extraction carriage is fully opened,
remove the door block (Fig. 14). Successive- remove the door block (Fig. 14). Successive-
and install the supplied union.
ly open the door (Fig. 15) and position the ly open the door (Fig. 15) and position the
9. Position the metal box containing the elec-
anti-grease filters (Fig. 16). anti-grease filters (Fig. 16).
tronic components in an easily accessible
6. The motor can be installed on the front or position in the case of any technical interven-
6. The motor can be installed on the front or
tion. rear part of the downdraft. The air outlet must rear part of the downdraft. The air outlet must
Connect the internal motor or the external mo-
be pointed upwards or downwards. be pointed upwards or downwards.
EN
tor's cable to the terminal board found inside the
7. Assemble the ducting for the air outlet. 7. Assemble the ducting for the air outlet.
plastic box of the downdraft wiring. Make sure
8. In the case of the version with an external 8. In the case of the version with an external
to respect the colors of cables when performing
motor, choose the air outlet most suitable motor, choose the air outlet most suitable
cordance with the information reported on
the electrical connection (fig.18).
from the five possibilities (refer to the design from the five possibilities (refer to the design
the relative technical data plate.
in the TECHNICAL ILLUSTRATION chapter) in the TECHNICAL ILLUSTRATION chapter)
4. After completing the installation and having
and install the supplied union. and install the supplied union.
connected the downdraft to the mains elec-
9. Position the metal box containing the elec- 9. Position the metal box containing the elec-
tricity, check that the red key on the electron-
tronic components in an easily accessible tronic components in an easily accessible
ic metal box is pressed and then activate the
position in the case of any technical interven- position in the case of any technical interven-
lifting of the extraction carriage by pressing
tion. tion.
the key.
5. When the extraction carriage is fully opened,
remove the door block (Fig. 14). Successive-
ly open the door (Fig. 15) and position the
anti-grease filters (Fig. 16).
6. The motor can be installed on the front or
rear part of the downdraft. The air outlet must
be pointed upwards or downwards.
7. Assemble the ducting for the air outlet.
8. In the case of the version with an external
motor, choose the air outlet most suitable
from the five possibilities (refer to the design
in the TECHNICAL ILLUSTRATION chapter)
and install the supplied union.
9. Position the metal box containing the elec-
tronic components in an easily accessible
position in the case of any technical interven-
tion.
S-DDH1 S-DDH2
S-DDH1 S-DDH2 S-DDH1 S-DDH2
te the