Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SEWOO LK-P20W
Summary of Contents for SEWOO LK-P20W
- Page 1 SEWOO TECH CO.,LTD. Doosung BD, 689-20, Geumjeong-dong, Gunpo-si, Gyeonggi-do, 435-862, Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-P20W MOBILE PRINTER All specifications are subject to change without notice Rev. 2.0...
-
Page 2: Table Of Contents
Table of Contents RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION 1. Unpacking 2. Product overview 3. Usage and Installation 3-1. Control panel usage 3-2. Battery Installation 3-3. Charging battery 3-4. -
Page 3: Unpacking
1. Unpacking 2. Product overview Front Standard MSR Slot (Optional) Power switch Open Button Printer Battery Belt Buckle Paper feed button IC Card Slot (Optional) Charger Serial Cable USB Shelded Cable DC Power Rear Belt clip hole Battery Roll paper Quick Manual Optional Battery recharger... -
Page 4: Usage And Installation
3. Usage and Installation 3-2 Battery Installation 3-1 Control panel usage Hook Button Name function This button is used to turn the printer on and off. Power When the printer is off, press this button for approximately 3 seconds button and it will turn on the power. -
Page 5: Charging Battery
3-3 Charging battery 3-4 Battery charger usage Optional Lamp Lamp 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 1. Insert the battery into the battery holder as shown above 3. -
Page 6: Usage Of Cigar Jack For Charging (Optional)
3-6 Battery removal 3-5 Usage of Cigar Jack for charging Optional Printer Rotate the belt clip as shown Battery holder Connect the car cigar JACK charger into the printer or battery holder. Input 12 ~ 24V Output 8.4V 0.8 ~ 1.2A NOTE Remove the battery as shown Use the Cigar Jack offered by the manufacturer... -
Page 7: Belt Clip Usage
3-7 Belt Clip usage 3-8 Loading the media. Insert screw into belt clip. Place the paper roll as shown. Make sure the paper is placed in Press the cover open button and open right direction. Tighten the screw with driver as shown Pull a short length of paper out of the printer and close the cover. -
Page 8: Optional
3-9 Shoulder Strap Usage 3-10 Leather case usage Optional Optional Place the end of strap into the hook of Insert the strap into the hook on shoulder strap. the printer. Open the leather case Place the printer into the leather case Close the Velcro and stick the cover. -
Page 9: Self Test
3-11 Self Test When the printer is installed initially or when you face a problem, you can run the self test and check the information about -Control Circuit, Mechanism, Print Quality, ROM Version After checking with self-test and no issues are found, you can examine other devices and software. -
Page 10: Msr Usage (Optional)
3-13 IC CARD usage 3-12 MSR usage Optional Optional Insert the card in the direction of the arrow as shown in the picture. Insert and swipe the card in the direction of the arrow as shown in the picture. -
Page 11: Peripherals Connection
4. Peripherals Connection This product can communicate with other devices via Wifi(802.11b/g) 4-2 Interface Cable Connection communication and cable. 4-1 Wifi(802.11b/g) Connection Serial 1. The Printer can be connected to devices equipped with wifi(802.11b/g) communication capacity (PDAs, PCs, etc.) 1. Connect USB or Serial cable into the cable connector on the printer. 2. -
Page 12: Specification
5. Pritner Specification 5-1. Specification 5~40℃ Temperature operation Printing Method Direct Thermal storage -10~50℃ Printing Speed 80mm/sec Humidity operation 35 ~ 95% Resolution 203 DPI X 203 DPI storage 10 ~ 95% Character ALPHA NUMERIC Character, Extension Character Barcode EAN-8, EAN-13, Code39, ITF, UPC-A, Codabar, Code93, Code128, PDF417(2D) Preventing Overheating ●... -
Page 13: Certification
6.Certification FCC Information CAUTION Antenna shall be mounted in such a manner to minimize the potential This device complies with part 15 of the FCC Results. Operation is subject for human contact during normal operation. The antenna should not to the following two conditions: be contacted during operation to avoid the possibility of exceeding the (1) This Device may not cause harmful interface, and FCC radio frequency exposure limit. -
Page 14: Setting Up The Software
7. Setting up the software Please refer to the programming manual included in CD.
Need help?
Do you have a question about the LK-P20W and is the answer not in the manual?
Questions and answers