Advertisement
Quick Links
READ THE OPERATING AND MAINTENANCE MANUAL
Service of the Console
The console allows to:
-
set the chopper card for a personalised behaviour of the traction motor
-
read the type of the alarm for a correct and easy trouble shooting
-
test the different electric values and the state of the electric circuit relative to the traction
Use of the Console
The use of the instrument is very easy and comparable to one of the most common electronic devices
(such as mobile phones).
The sequence to follow always for the console connection is:
1. SWITCH OFF THE GENERAL KEY of the machine
2. take off the connector E from the chopper
3. connect the console in place of the connector E. If the operation connection results to be difficult,
check that the connector is positioned in the correct direction.
4. switch on the key and work with the console
5. quit from all the programs (main menu of the ignition) and SWITCH OFF THE GENERAL KEY of the
machine
6. disconnect the console connector and plug in the connector E
THE WRONG OPERATION SEQUENCE CAN EASILY COMPROMISE
THE FUNCTIONALITY OF THE CHOPPER CARD OR OF THE CONSOLE
ADJUSTMENT
AND
INSPECTION
MAGNA 65-70-75-83
Doc.
10004978
Issued
27/03/2008
Rev.
00
P a g .
1 d i 19
Advertisement
Related Manuals for Fimap MAGNA 65
Summary of Contents for Fimap MAGNA 65
- Page 1 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 d i 19 READ THE OPERATING AND MAINTENANCE MANUAL Service of the Console The console allows to: set the chopper card for a personalised behaviour of the traction motor...
- Page 2 : CUT BACK SPEED 1 (minimum speed machine) and the CUT BACK SPEED 2 (medium speed machine). All the other parameters are decided in Fimap and they are related to the traction motor. It is forbidden to change them without previous Fimap authorisation.
- Page 3 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 3 d i 19 Flow chart of the console HEADING enter enter LIST OF PARAMETERS PROGRAM ROLL to select DO YOU WANT TO PARAM SET to change...
- Page 4 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 4 d i 19 Alarms and Decoder The chopper card visualises an anomaly on two levels of information 1. through a red alarm led which blinks for a quantity of times relative to the type of anomaly 2.
- Page 5 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 5 d i 19 Number of MESSAGE NOTES blinkings Incorrect starting sequence Possible causes error in the sequence Key/drive selection made by the operator the micro pedal and/or micro drive are stuck...
- Page 6 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 6 d i 19 The chopper card recognizes an anomaly in the mechanical stroke of the accelerator Possible causes operator switched machine with accelerator pressed down pressed...
- Page 7 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 7 d i 19 The chopper card works out of the temperature range (-30°C + 70°C) Possible causes chopper card faulty TH PROTECTION the machine runs in braking condition and the chopper gets...
- Page 8 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 8 d i 19 Chopper card setting 1. Switch OFF the general key and plug in the special connector. The OFF condition is necessary to save the memory card from loss of data).
-
Page 9: Select Program
Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 9 d i 19 7. At the end press OUT and confirm ENTER if some parameter has been changed. ATTENTION: PLEASE DO NOT CHANGE ANY PARAMETERS RELATED TO THE SAFETY... - Page 10 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 0 d i 19 PROGRAM VACC 8. Run through the different menus moving from the menu RESTORE to the menu PROGRAM VACC (to relate the pedal accelerator...
- Page 11 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 1 d i 19 Tester function After having connectec the console, the heading message will C83-104 appear. This notice say the chopper model, the default machine where it is (or was) installed and the worked hours of the device.
-
Page 12: Motor Voltage
Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 2 d i 19 Verify the temperature on the power stage of the chopper card. TEMPERATURE The temperature should be the same of the environment one only if the machine had been turned off for at least 1 hour and just DEGREES = 17°C... - Page 13 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 3 d i 19 Functional inspection electric layout 1. Remove the battery connector 2. Verify the cleanliness and the tightening of the power cable connections. . (on power switches, fuses, motors, batteries, ecc.) 3.
- Page 14 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 4 d i 19 Water unit inspection Check the cleanliness and the operation of the solution filter Fill the solution tank and check there is no leakage on the...
-
Page 15: Adjustment And Inspection
Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 5 d i 19 Brush head frame adjustments (for both cylindrical and rotating brush head) For the general check please verify the following brush head level adjustments:... - Page 16 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 6 d i 19 Up-down microswitches adjustments for the brush head On the actuator’s support of the brush base are the microswitches with corresponding stops: •...
- Page 17 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 7 d i 19 Splash guards adjustment: operate on the screw to adjust the height of the rubber that must touch the floor for all its length.
- Page 18 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 8 d i 19 Brake and steering adjustment 1. Steering tension chain adjustment: • remove the foot board • release the lock nut and screw the...
- Page 19 Doc. 10004978 ADJUSTMENT Issued 27/03/2008 MAGNA 65-70-75-83 Rev. INSPECTION P a g . 1 9 d i 19 Inspections functions of the machine Check the functionality of the seat microswitch; Check the functionality of the acceleration pedal; Check the functionality of the brush base;...
Need help?
Do you have a question about the MAGNA 65 and is the answer not in the manual?
Questions and answers