Page 3
PROPRIETARY STATEMENT This document and subject matter disclosed herein are proprietary items to which BAE SYSTEMS retains the exclusive right of dissemination, reproduction, manufacture and sale. This document is provided to the individual or using organization for their use alone in the direct support of the associated equipment unless permission for further disclosure is expressly granted in writing.
Page 4
E2730A VXI RF TUNER LIST OF EFFECTIVE PAGES Page Number Description Revision Cover Proprietary/Export/Safety Notices List of Effective Pages Intentionally Blank Revision Record Intentionally Blank vii thru x Table of Contents Section Cover 1-ii Intentionally Blank 1-1 thru 1-4 Section One Pages...
Page 5
E2730A VXI RF TUNER THIS PAGE INTENTIONALLY LEFT BLANK LIST OF EFFECTIVE PAGES...
Page 6
E2730A VXI RF TUNER E2730A VXI RF TUNER INSTALLATION AND OPERATION MANUAL REVISION RECORD Revision Description Date Production Release. 6/2002 REVISION RECORD...
Page 7
E2730A VXI RF TUNER THIS PAGE INTENTIONALLY LEFT BLANK REVISION RECORD...
2.2.7 2nd LO IN/OUT (W3J3) ....................2.2.8 1st LO IN/OUT (W1J1) ....................Power and Cooling Requirements Versus Mainframe Selection........Setting the E2730A 's Logical Address................. Installing the E2730A in the Mainframe..............2-10 VXI Compliance D16/D32.................... 2-10 VXI Signal List ......................
E2730A VXI RF TUNER TABLE OF CONTENTS (Continued) SECTION 3 LOCAL OPERATION Paragraph Page Introduction ........................Indicators........................3.2.1 RUN Indicator, Green Led .................... 3.2.2 COR Indicator, Red Led....................3.2.3 ERR Indicator (A5DS3) ....................Tuner Control Using the VXI Interface ................
Page 10
Paragraph Page Unit Numbering Method ....................Reference Designation Prefix ..................List of Manufacturers....................Parts List........................Type E2730A VXI RF Tuner, Main Chassis ............... LIST OF TABLES Table Page E2730A VXI RF Tuner Specifications ................ List of Connectors ......................List of Mating Connectors ....................
Page 11
Figure Page E2730A VXI RF Tuner ....................Location of External Connectors and Indicators............AUX Connector Pin Assignments................. Setting the E2730A 's Logical Address................. E2730A Properly Installed in a Vertical Mainframe ........... 2-10 E2730A SRQ Structure Diagram ................. 3-18 FOLDOUTS Foldout...
2700 MHz range and 11 dB in the 20 to 1200 MHz range. See Table 1-1 for a list of general specifications. The E2730A has a frequency tuning range of 20 to 2700 MHz, in 1-kHz steps, and provides up to 56 dB of manual gain control.
Page 15
Refer to Section 2 for further details on the unit’s input/outputs. Two LEDs (ERR and RUN) on the E2730A front panel monitors tuner operations and provide indications for operator information and control. Refer to Section 3 for more information on these indicators.
Page 16
E2730A VXI RF TUNER Table 1-1. E2730A VXI RF Tuner Specifications Frequency Range ............20-2700 MHz Tuning Resolution ............1 kHz Internal Reference Accuracy ........±1.0 ppm maximum (0 to 40° C) External Reference Input..........10 MHz (across VXI backplane or front panel) RF Input...............
LO unlocks from what it considers uninstalled boards. It changed identity information to Agilent Technologies E2730A. In addition, the #CDT and #CSN commands also changed format, to comply with customer requests. The YIG calibration routine has been enhanced to help the test technicians calibrate more units on the first try.
SECTION 2 INSTALLATION 2.1 UNPACKING AND INSPECTION The E2730A and its accessories are shipped cushioned between molded-in- place expanded plastic pads in a double-walled carton. After unpacking the equipment, retain the shipping container and packing material until the equipment has been thoroughly inspected and it is ensured that reshipment is not necessary.
Page 21
E2730A VXI RF TUNER Table 2-1. List of Connectors Connector Ref Des Function VXI P1 A1P1 (Multipin) Standard VXIbus P1 connector VXI P2 A1P2 (Multipin) Standard VXIbus P2 connector A5J2 (Multipin) Auxiliary RS-232 Control RF IN (SMA) Antenna Input 10 MHz EXT REF...
Page 22
E2730A VXI RF TUNER ROW B PIN 1 ROW C PIN 1 ROW A PIN 1 A1P1 PIN 32 (ALL ROWS) ROW B PIN 1 ROW C PIN 1 ROW A PIN 1 A1P2 PIN 32 (ALL ROWS) 99-0087 Figure 2-1. Location of External Connectors and Indicators...
E2730A VXI RF TUNER 2.2.1 VXI P1, STANDARD VXIbus P1 (A1P1) This multipin connector is the standard multipin, VXIbus P1 connector. Refer to Section B of the VXIbus System Specification for details on the signals resident at this connector. For convenience, the pin assignments of this connector are defined in Table 2-3.
Page 24
E2730A VXI RF TUNER 2.2.2 VXI P2, STANDARD VXIbus P2 (A1P2) This multipin connector is the standard multipin, VXIbus P2 connector. Refer to Section B of the VXIbus System Specification for details on the signals resident at this connector. For convenience, the pin assignments of this connector are defined in Table 2-4.
E2730A VXI RF TUNER 2.2.3 AUX, AUXILIARY RS-232 CONTROL CONNECTOR (A5J2) The AUX connector is a 9-pin D-type microconnector. Pin 1 (TX) and pin 2 (RX) provide an RS-232C port which may be used to control the tuner. The default baud rate is 19200. However, baud rates of 1200 to 38400 are supported via the #CBR command as described in Section 3 of this manual.
E2730A tuner to form a two-channel, phase-coherent tuner. This connector, via internal switching, may also be used to input a 2nd LO frequency from another E2730A tuner to form a Master/Slave relationship. The appropriate operating mode (independent, master or slave) must be remotely selected via the LOM command which is described in Section 3 of this manual.
(ON = logic 0, OFF = logic 1). Figure 2-3 provides the combination of switch position settings required for various addresses. When the E2730A is configured as a DC device, the Resource Manager assigns a logical address to it during the power-on sequence. When the tuner is in the SC configuration, it responds to controller commands only after receiving the address as identified by the DIP switch.
Page 28
SC 0* SC 1 SC 2 SC 4 SC 8 DC 255 * This address is not a Slot 0 Controller recognized servant address. Do Not configure the switch to provide this address. Figure 2-3. Setting the E2730A Logical Address INSTALLATION...
Before installing the tuner, ensure its logical address is set to the proper setting (refer to paragraph 2.4). The E2730A should be installed vertically in a C-size mainframe. Refer to the equipment manual provided with the mainframe being used for proper module installation instructions.
1ST LO IN/OUT 99-0088 Figure 2-4. E2730A Properly Installed in a Vertical Mainframe 2.7.1 VXI 10 MHz REFERENCE A VXI 10 MHz reference signal is generated within the slot zero controller and distributed to each tuner via the VXI bus. The VXI 10 MHz reference is a differential ECL signal, which is available on the CLK10+ and CLK10- lines.
E2730A VXI RF TUNER 2.8 SERVICE AND SUPPORT Any adjustment, maintenance, or repair of this product must be performed by qualified personnel. Contact your customer engineer through your local Agilent Technologies Service Center. AGILENT ON THE WEB You can find information about technical and professional services, product support, and equipment repair and service on the Web: http://www.agilent.com/contacts/English/noscript.html...
All tuner indicators are located on the front panel. Two LEDs are provided for monitoring the operating status of the unit. The following paragraphs further explain the function of each LED. The E2730A has no front panel controls. 3.2.1 RUN INDICATOR, GREEN LED This green LED illuminates approximately one second after power is applied to the tuner, indicating that the tuner’s microcontroller is active...
Commands and IEEE-488.2 Protocol. Binary registers may also be used for some of the most common functions. The following paragraphs provide further details on how the E2730A is controlled in the VXI architecture using either command method. 3.3.1 VXIBus/E2730A INTERFACE All tuner operations are directed by commands received over the VXIbus.
E2730A is determined by the Resource Manager by reading the tuner's MODID (module identification) line during the power-up and initialization routine. The E2730A contains an offset register that can be written to by the resource manager to define its address. Refer to Section F in the VXIbus Specification for further details on dynamic configurations.
E2730A VXI RF TUNER 3.3.4 E2730A COMMUNICATION PROTOCOL The operation of the E2730A is normally controlled using word serial commands (refer to the VXIbus Specification, paragraph C.3.3.1) and IEEE-488.2 modeled ASCII mnemonics. The Tuner also supports register based VXI operations. Each communication method is discussed in the following paragraphs.
Page 38
E2730A VXI RF TUNER character. Numeric arguments are represented by the least number of digits necessary to represent the entire range of the argument. If the argument can be negative then a sign character ("+" or "-") is always given. Multiple arguments are delimited by "," character(s). Responses to concatenated queries are concatenated in the output buffer, delimited by “,”...
The available VXI binary commands are discussed in the following paragraphs. BINARY COMMANDS The E2730A may be controlled by writing commands to either the VXI Device Dependent Registers or through the lower portion of “Upper Memory” as assigned by the Resource Manager. Binary commands allow control of frequency and attenuation.
Page 40
E2730A VXI RF TUNER Table 3-2. VXI Memory/Register Based Commands Address Description Base + 0x00xx Fast Command 1 - Not Used At This Time Fast Command 2 - Not Used At This Time Fast Command 3 - Not Used At This Time...
The E2730A tuner is a message-based VXI device with interrupter capability. The tuner requires one VXIbus interrupt line for operation. The interrupt line is used when the E2730A tuner has asserted a service request (SRQ). The “assign interrupt line” word serial command (see paragraph 3.3.1) is used to assign interrupt lines to a VXIbus device.
REFERENCE SELECTION The E2730A can have its frequency referenced to one of three sources: an internal reference oscillator, an external 10 MHz input on the front panel of the tuner or the VXI 10 MHz bus reference. The tuner always powers up using the internal reference oscillator.
This query allows an application to configure itself based on the current frequency limits. While all of the E2730A tuners currently respond with the same limits, future units could potentially have extended capabilities. The frequency range query will respond with a lower frequency limit of 2 MHz and an upper frequency limit of 2700 MHz.
Reset = TSP 2 Example = TSP 1 TUNER ATTENUATION OPERATIONS Gain control of the E2730A is via the ATN command. The ATN command allows the reduction of gain from maximum (ATN 0) in approximately 2-dB increments to gain minimum (ATN 56).
E2730A VXI RF TUNER 3.4.3 MEMORY OPERATION A memory channel contains an entire setup for a single frequency. A total of 200 memory channels are provided. Memory channels may be accessed directly via the Store Memory Direct (SMD) and Read Memory Direct (RMD) commands.
The mnemonics in this message category are always valid. These commands establish communications and control the event interrupts between the E2730A and the controller and do not alter the hardware functions of the tuner. The commands associated with this message category are described in the following paragraphs.
Page 49
E2730A VXI RF TUNER The ESB bit indicates an enabled event in the Event Status Register (*ESR) occurred. The *ESR contains bits to indicate Operation Complete (OPC), Query Error (QYE), Device Dependent Error (DDE), Execution Error (EXE), Command Error (CME) and Power On (PON). The Event Status Enable Register (*ESE) contains a corresponding enable bit for each event.
Page 50
*OPT? *OPT nr1 Request a bit-mapped value of the installed options. No options are currently defined for the E2730A tuner (always returns 000). Reset: n/c Example: *OPT 000 RTK nrf? RTK nr1 Request Token. Returned value will either be the number entered or another controller’s token...
Figure 3-1. E2730A SRQ Structure Diagram 3.4.5 HARDWARE ERROR MESSAGES The E2730A performs both startup built-in internal tests and continuous monitoring of key tuner sections. The tuner responds to a command which reruns the startup test and also queries to determine the current status of these operations along with the history since the last status request.
Page 52
E2730A VXI RF TUNER During normal operation the tuner LO status is continually monitored. The error status bits are set to indicate the results of the monitoring operations. The tuner includes three command queries for determining hardware error status. Each of the commands returns a bit mapped value between 0 and 65535, where each bit indicates the hardware status of a particular subsystem of the tuner.
Page 53
E2730A VXI RF TUNER Table 3-11. Hardware Error Messages (Continued) Command Response Description Not Used CDE? (Cont’d) EED, EEPROM has been defaulted 1024 Not Used 2048 Not Used 4096 EEF, EEPROM failure to be written 8192 Not Used 16384 BNI, Board Not Installed...
The commands in this message category are only implemented to provide compatibility with other receivers. Many of the commands have no meaning with respect to the E2730A, but are provided to obtain interface backward compatibility. The mnemonics associated with this message category are listed in Table 3-13.
Page 55
E2730A VXI RF TUNER Table 3-13. Compatibility Messages Command Response Description Advance to the next frequency if the current state is active. AFC nrf Select AFC mode. AFC? AFC 0 Request AFC mode. AGC nrf Select the gain control mode.
Page 56
E2730A VXI RF TUNER Table 3-13. Compatibility Messages (Continued) Command Response Description #CBW nrf,nrf,...nrf CHN 0 Set IF Bandwidth Data CHN? CLG nr1,nr1,...nr1 Request current memory channel accessed for sweep or step operation. #CLG? Request dBm Table. Always returns 0.
Page 57
E2730A VXI RF TUNER Table 3-13. Compatibility Messages (Continued) Command Response Description DSO? DSO 0 Returns status of Digital Scan Output – always returns 0 DWS? DWS 0 Request the current dwell state. Restore to active a suspended sweep or step operation.
Page 58
E2730A VXI RF TUNER Table 3-13. Compatibility Messages (Continued) Command Response Description LCK nrf,nrf,nrf Enter a lockout channel to be used in Sweep operation. Load tuner attenuation (ATN) to reflect current AGC attenuation value. LDW nrf Set scan post (loss) dwell timer.
Page 59
E2730A VXI RF TUNER Table 3-13. Compatibility Messages (Continued) Command Response Description RSR? RSR 00000 Read the Receiver Status Register. RLK nrf ? Recall the specified lockout channel. nr1,0000.0000, 0000.0000 #RVB nrf? #RVB Request Video Bandwidth Settings nr1,0000.00000 Bandwidth Slot SAC nrf Suspend Action Control register.
Page 60
E2730A VXI RF TUNER Table 3-13. Compatibility Messages (Continued) Command Response Description SST? SST 0 Request Step operation status. STL? Request the step channel list. STL nrf,... nrf Enter a step channel list. (nrf:nrf),...(nrf:nrf) Suspend the sweep or step operation.
E2730A VXI RF TUNER 3.4.8 USER CONFIGURATION MESSAGES The commands in this message category, which begin with the pound sign (#), are valid only when the tuner is in configuration mode. These commands are used to configure the tuner’s EEPROM. The parameters associated with these commands are retained by the tuner and are not reset on power up.
E2730A VXI RF TUNER 3.4.9 FACTORY CONFIGURATION MESSAGES The commands in this message category, which begin with the pound sign (#), are valid only when the tuner is in configuration mode. These commands are used to configure the tuner’s EEPROM with parameters required for proper operation.
Page 63
Default: #MDL ′E2730A ′ ,2B6 Example: #MDL ′E2730A ′ ,2B6 Note: The first six (E2730A) of the seven characters must never change. If they do, then the EEPROM will be reset upon the next power-up of the unit.
Page 64
E2730A VXI RF TUNER 3.4.10 MAINTENANCE MESSAGES The commands in this message category are for maintenance operations only. These commands are not intended for normal applications and may interact with normal operations of the tuner. Powering the tuner down and back up will eliminate any of those interactions and return the tuner to normal operation.
Page 65
E2730A VXI RF TUNER Table 3-16. Maintenance Messages (Continued) Command Response Description #MEM? #MEM nr1,nr1,nr1 Read a memory location. Field Parameter Range Memory Size 0 – byte; 1 – word; 2 – long word Memory Address 0 to 4294967295 Data Value...
Page 67
THIS PAGE INTENTIONALLY LEFT BLANK 4-ii...
Page 68
E2730A VXI RF TUNER SECTION 4 REPLACEMENT PARTS LIST 4.1 UNIT NUMBERING METHOD The method of numbering used throughout the unit includes the assignment of reference designations (electrical symbol numbers) to identify: assemblies, subassemblies, modules within an assembly, and discrete components. An example of the unit numbering method is as...
Page 69
E2730A VXI RF TUNER 4.4 PARTS LIST The following parts list contains all the major electrical components used in the unit, along with any mechanical parts which may be subject to unusual wear or damage. When ordering replacement parts, specify the unit type and the serial number.
Page 70
E2730A VXI RF TUNER MANUFACTURERS MFR. RECM DESIG DESCRIPTION ASSY PART NO. CODE VENDOR 4.5 TYPE E2730A VXI RF TUNER MAIN CHASSIS Revision 51 Digital Control PC Assembly 483136-001 14632 A1U18 EPROM, Programmed 181665-001 14632 A1U19 Same as A1U18 1st LO PC Assembly...
Page 71
E2730A VXI RF TUNER NOTES REPLACEMENT PARTS LIST...