Operation - Sammic UX-40 User Manual

Operation

[Models with electric dispensers]
tings
To enter this settings section, when turning on the machine, press
and hold the START button
program is loading.
ℹ Information
The values shown are equivalent to two digits to one decimal
place. Examples:
– 3.5 g/L: "35" is displayed.
– 0 .5 g/L: " o 5" is displayed.
• D ET DOSE g/l : dose of detergent in g/L.
• D ET FILL : detergent priming: ON-OFF (LCD: "on-00").
a) Press PROG or O PTIONAL
ing process.
> The detergent dispenser turns on for a few seconds and then returns to
OFF (00).
b) Press PROG or START
filled.
• R AID DOSE g/L: rinse aid dose in g/L.
• R INSE AID FILL : rinse aid priming: ON-OFF (on-00).
a) Press PROG or O PTIONAL
ing process.
> The detergent dispenser turns on for a few seconds and then returns to
OFF (00).
b) Press PROG or START
filled.
• WATER HARDNESS: enter the degree of water hard-
[D models]
ness (unit: French degree °fH, display shows "°F"). With this data
the machine programs the regeneration frequency necessary to
inform by means of the icon
Inlet water Number of regeneration cycles
hardness
Manual cycles
UX-40 D UX-50 D
°fH
0-20 93
21-30 °fH 57
31-40 °fH 33
°fH
41-50 25
Other activations
• [B models] WATER LEVEL (qualified technicians only): activa-
tion of tank water level display: ON-OFF (LCD: "on-00").
– Cycle times and texts are not displayed.
• [C models] B.PRES MANUAL: manual activation of rinse pump:
ON-OFF (on-00).
2.7.2 Other settings
To enter this settings section, when switching on the machine,
press and hold down the OPTIONALS button
seconds while the program is loading.
• L ANGUAGE
• RINSE TIME: modification of the time in time range between -2
and +2 seconds (s).
• ENERGY SAVING: ON-OFF (LCD: "on-00").
• SOFT START: ON-OFF (on-00). Progressive start of the wash
motor pump.
• TEMP UNITS: selection of temperature units °C/°F.
User's manual — 2900455/0
Dispensing and hardness set-
in the first few seconds while the
to activate (on) the detergent fill-
again until the pipe is completely
to activate (on) the detergent fill-
again until the pipe is completely
.
Automatic cycles
UX-50 CD UX-120 CD
112 10 20
72 7 15
49 5 10
29 4 6
in the first few
• REGEN COUNTER: displays the number of regeneration cycles
performed.
• CYCLE COUNTER: displays the number of wash cycles per-
formed.
• INITIAL SETTINGS: to restore the initial parameters of the
machine.
2.7.3 Screen test
To check that the LCD display segments are working:
1) W hen switching on the machine, press and hold down the
START and O PTIONAL
first few seconds while the program is loading.
⇒
A ll the screen icons light up.
2.7.4 Model settings
If the electronic board is changed or de-configured, the machine
requires the model to be adjusted by means of the following adjust-
ment section:
1) W hen switching on the machine, press and hold
few seconds while the program is loading.
2) T o choose the model number, press the buttons PROG
OPTIONAL .
3) C onfirm your selection by pressing the START button
Model Model
Number
2 UX-40
3 UX-40 B
4 UX-40 D
5 UX-40 BD
7 UX-50
8 UX-50 B
9 UX-50 D
10 UX-50 BD
12 UX-50 C
13 UX-50 BC
Notice
Error with boiler and tank level probes
If the selected model is fitted with boiler and tank level probes
and the probes are not connected, an error message is dis-
played. Conversely, if a model is selected that is not fitted with
the probes but the machine has them, an error message is dis-
played: MODEL NUMBER ERROR.
– If this error occurs, reconfigure the machine model for the elec-
tronic board.
3 Operation
⚠ W a rn in g
Risk of serious injury due to operation when the
machine is faulty
Using the machine when it is faulty or in poor condition can af-
fect personal safety and damage the machine.
– If you detect any fault or anomaly in the machine, contact an
authorised service agent immediately.
buttons simultaneously in the
in the first
and
.
Model Model
Number
14 UX-50 BCD
22 UX-100, UX-120
23 UX-100 B, UX-120 B
24 UX-120 V
25 UX-120 BV
26 UX-120 C
27 UX-120 BC
28 UX-120 BCD
32 UX-120 BCV
33 UX-120 BCDV
EN
7