Technical Specifications - Sammic UX-40 User Manual

Disposal
To install adjustable detergent dispensers, proceed as follows:
1) Access to the DD power strip on the lower front part of the
machine for the electrical connection of the soap dispenser.
This strip is controlled by solenoid valve EV1. Refer to the wiring
diagram for the correct connection order.
2) I nstall the soap injection fitting through the hole at the rear.
ℹ Information
Sammic declines all liability for defects caused by faulty con-
nections when installing the dispensers.
Rinse aid dispenser
Mains water dispenser
1) C heck that the rinse aid tank is full.
2) S tart the machine and stop the wash/rinse cycle 5 or 6 times by
successively pressing the PROG button
rinse aid pipe fills up and the rinse aid enters the boiler.
⇒
T he rinse aid can be adjusted using the adjustment screw on
the lower front part in the direction indicated.
Peristaltic dispenser
• T he dose is adjusted in the settings section of the control panel.
▶
[ p. 7 ]
• D uring installation, prime the detergent pipe from the settings
▶
section [ p. 7 ].
• T o check if the dose of rinse aid is effective, hold the glasses up
to the light.
– If there are drops of water on the glass, the dose is insufficient
– I f there are streaks on the glass, the dose is too high.
Installation with descaler
Install a Sammic descaler when the limescale content in the
machine feed water exceeds 10 °fH (French grade).
• I nstallation instructions are supplied with the descaler.
• A void flow reductions (choking) before and after installation, as
they cause pressure losses.
Installation with back-up valve
Install a back-up valve when the water pressure to be supplied to
the machine is lower than the pressure specified for that model.
• T he back-up valve can be installed at any point near the unit,
extending the water line and stopcock to the back-up valve.
• M ake sure that the stopcock is still accessible.
•
C onnect one end of the back-up valve to the stopcock and the
other end to the hose supplied with the machine.
5 Disposal
Packaging
Follow current environmental standards in your country to dispose
of the packaging.
User's manual — 2900455/0
Machine
This machine is subject to the provisions of Euro-
pean Directive 2012/19/EU on waste electrical and
electronic equipment. The machine is marked with
the WEEE (Waste of Electrical and Electronic
Equipment) symbol:
⭆
D o not dispose of this machine in normal house -
hold waste.
⭆
D ispose of the machine at an authorised waste management
centre or through municipal waste disposal entities. Comply
with the applicable regulations.
You can obtain information about waste disposal and the location
of your nearest recycling centre, for example, from your municipal
cleaning service.
, checking that the
6

Technical specifications

Front glasswashers and dishwashers
Specifications
Basket dimensions [mm]
Maximum crockery
height
Provision of baskets
Cycle [s]
Basket production/h
Electrical power supply
Electric power
Motor pump
Washing power
Boiler power
Total power
Temperatures
Washing
Rinse
Water capacity
Wash tank
Rinse boiler
Water consumption
(2 bar)
External Dimensions
Width [mm]
Depth [mm]
Height [mm]
[*] [S models with double wall]
UX 40 UX 50 Lite
Glasswasher Front
400 x 400 500 x 500
300 mm 365 mm
2
90/120/ 90/110/120/180/240
150/180
40/30/24/20 40/33/30/20/15
230 V/50 Hz/∼1 400 V/50 Hz/∼3
250 W/0.33 HP 750 W/1 HP
1,200 W 1,800 W
2,800 W 3,000 W
3,050 W 3,750 W
40-7 0 °C (104-15 8 °F)
65-87 °C (149-189 °F)
9.0 L 14.0 L
4.5 L 8.0 L
1.9 L 2.5 L
470 (490 [*]) 580 (600 [*])
535 635
710 830
EN
UX 50
Front
5,000 W
5,750 W
13