Advertisement
Quick Links
Product
The remote display assembly is a remote Flexible User Interface fitted in a specially sized box and
Overview
connected to the master controller. These instructions cover the following units:.
•
4100-9401 Remote Display Assembly, Domestic, Red
•
4100-9402 Remote Display Assembly, Domestic, Beige
•
4100-9421 Remote Display Assembly, Canadian/French, Red
•
4100-9422 Remote Display Assembly, Canadian/French, Beige
•
4100-9441 Remote Display Assembly, International, Red
•
4100-9442 Remote Display Assembly, International, Beige
This product is compatible with both 4100U and 4100ES Fire Alarm Control Panels (FACP).
Cautions
READ AND SAVE THESE INSTRUCTIONS
and
followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper
Warnings
installation.
DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED
inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify
an authorized Simplex product supplier.
ELECTRICAL HAZARD
be performed by a representative or authorized agent of your local Simplex product supplier.
STATIC HAZARD
• Ground yourself before opening or installing components.
• Prior to installation, keep components wrapped in anti-static material at all times.
In This
This document covers the following subjects:
Document
Overview
Installing the Remote Display Assembly
Wiring the Remote Display Assembly
Replacing the Remote Display Assembly
Reference
For instructions on programming the Flexible User Interface refer to the ES Panel Programmer's
Manual (574-849).
© 2006-2011 SimplexGrinnell LP. All rights reserved.
Specifications and other information shown were current as of publication and are subject to change without notice.
Simplex and the Simplex logo are trademarks of Tyco International Ltd. and its affiliates and are used under license.
-
Follow the instructions in this installation manual. These instructions must be
- Disconnect electrical field power when making any internal adjustments or repairs. All repairs should
- Static electricity can damage components. Handle as follows:
Description
firealarmresources.com
Remote Display Assembly
Installation Instructions
- Upon unpacking your Simplex product,
Page
2
5
8
10
579-687
Rev. D
Advertisement
Related Manuals for Simplex 4100-9401
Summary of Contents for Simplex 4100-9401
- Page 1 © 2006-2011 SimplexGrinnell LP. All rights reserved. Specifications and other information shown were current as of publication and are subject to change without notice. Rev. D Simplex and the Simplex logo are trademarks of Tyco International Ltd. and its affiliates and are used under license. firealarmresources.com...
- Page 2 Since the printed circuit boards and LCD are factory-installed within the RDA enclosure, hardware installation consists of surface mounting the enclosure to the wall, and completing the RUI circuit connection. The 4100-9401 Flexible User Interface remote display assembly contains the following: •...
- Page 3 Overview, continued The Flexible User Interface Controller Board has three main functions: it stores and runs the control Flexible User Interface software used to manage the display, communicates with the FACP master controller via internal or Controller Board external RUI, and processes front panel operator input. SW-1 SW-2 LEDS 1-6...
- Page 4 Overview, continued The transponder interface card housed in the Flexible User Interface remote display assembly is a varia- Transponder Interface Card tion of the TICs used in the FACP Miniplex, and follows the same wiring guidelines as the Miniplex (TIC) TIC.
- Page 5 Installing the Remote Display Assembly In order to install the RDA, the back box must be prepared for installation. The contents of the box must Prepare the Remote Box be removed and a wiring hole must be drilled into the back of the box. 1.
- Page 6 Installing the Remote Display Assembly, continued Insert a mounting screw in both the top right and top left mounting holes in the back box. Install the Remote Box Tighten the two mounting screws, but leave a 1/8-inch (3-mm) gap from the seated position of each screw.
- Page 7 Installing the Remote Display Assembly, continued Table 1 : SW1 Switch Address Configurations Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 firealarmresources.com...
- Page 8 Wiring the Remote Display Assembly The remote display assembly is wired as shown in Figure 6. To connect the remote display assembly to Overview the host panel, the TIC must be wired to the host panel via RUI cabling. This section explains how to wire the RDA to the FACP, and how to set up a system with multiple transponders connected to the same host panel.
- Page 9 Wiring the Remote Display Assembly , continued Refer to Figure 7 for the wiring diagram to connect one or more Flexible User Interface(s) to a FACP. Wiring Instructions Power must be supplied to the Flexible User Interface by connecting TB1 of the TIC to an auxiliary power tap.
- Page 10 Replacing the Remote Display Assembly If the Flexible User Interface panel on the remote display assembly stops functioning properly then it Overview must be replaced. Follow these steps to first remove the malfunctioning panel, and install the new panel. Removing the Before installing the new remote display assembly, the old door assembly must be removed.
- Page 11 Replacing the Remote Display Assembly, continued With the old assembly removed, the remote box is ready for the new remote display assembly. Installing the New Remote Orient the new remote display assembly so that the graphic overlay and LCD screen face Display downward, and the bottom of the assembly is set against the bottom edge of the remote box.
- Page 12 579-687 Rev. D firealarmresources.com...
Need help?
Do you have a question about the 4100-9401 and is the answer not in the manual?
Questions and answers