Simplex 4100-S1 Programming Manual
  1. Manuals
  2. Brands
  3. Simplex Manuals
  4. Control Panel
  5. 4100-S1
  6. Programming manual
Simplex 4100-S1 Programming Manual

Simplex 4100-S1 Programming Manual

Fire indication panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
4100U-S1 Fire Indicator Panel
Programming Guide
Australian
Programming
Guide
LT0400
Iss 1.4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4100-S1 and is the answer not in the manual?

Questions and answers

Related Manuals for Simplex 4100-S1

Summary of Contents for Simplex 4100-S1

  • Page 1 4100U-S1 Fire Indicator Panel Programming Guide Australian Programming Guide LT0400 Iss 1.4...

  • Page 3: Amendment Log

    Document: LT0400 4100U-S1 Programming Guide AMENDMENT LOG 28 November 2006 Original Issue 4 June 2008 Updated to match 12.05.02 Exec release 19 August 2010 Updated with Aust. message library loaded as primary 29 September 2010 Revised AS1668 Section 15 December 2010 Updated to match 12.06.01 Exec release and new templates.

  • Page 4: Table Of Contents

    4100U-S1 Programming Guide Document: LT0400 TABLE OF CONTENTS AMENDMENT LOG 1 INTRODUCTION 1.1 ABOUT THIS MANUAL 1.2 BEFORE YOU START 2 SYSTEM OVERVIEW 2.1 GENERAL DESCRIPTION 2.2 PROGRAMMING 3 ABOUT THE PROGRAMMING TOOLS 3.1 GENERAL 3.2 4100U PROGRAMMER 3.3 4100U-S1 CONFIGURATION TEMPLATES 3.4 4100U PROGRAMMER INSTALLATION AND LAUNCH 3.5 STEPS TO CONFIGURING A NEW SYSTEM 3.6 UPGRADING AN EXISTING CONFIGURATION...
  • Page 5 Document: LT0400 4100U-S1 Programming Guide 6.3.6 4090-9118 RELAY IAM WITH T-SENSE INPUT 6.3.7 4090-9119 RELAY IAM WITH UNSUPERVISED INPUT 6.3.8 4090-9120AU 6 POINT I/O MODULE (4 INPUTS, 2 RELAY OUTPUTS) 6.3.9 4090-9116 ADDRESSABLE IDNET ISOLATOR 6.3.10 4090-9117AU ADDRESSABLE IDNET POWER ISOLATOR 6.4 IDNET DEVICES TYPICAL APPLICATIONS 7 ADDING ZONE DISPLAYS 7.1 GENERAL...
  • Page 6 11.4 DIRECT CONNECTION TO THE PANEL 11-4 11.5 DOWNLOADING THE CFIG FILE 11-5 11.6 UPLOADING FROM THE PANEL 11-6 11.7 SENDING 4100U FILES TO SIMPLEX. 12-1 12 APPENDICES 12.1 APPENDIX A – AS4428.1 OPERATION 12-2 12-3 12.2 APPENDIX B - COMMON VARIABLES AND CUSTOM CONTROL 12.2.1 DIGITAL PSEUDO POINTS...

  • Page 7: Introduction

    Document: LT0400 4100U-S1 Programming Guide System Overview 1 Introduction Issue 1.4 15 December 2010 Page 1-1...

  • Page 8: About This Manual

    4100U-S1 Installation and Maintenance Manual for details about this. This manual does not cover configuration of networked 4100U-S1 systems. Contact your local Simplex office/dealer for assistance with this. The manual is divided into the following chapters: Chapter 2 describes the 4100U-S1 system hardware and how this affects the configuration procedure.

  • Page 9: Before You Start

    Document: LT0400 4100U-S1 Programming Guide System Overview Appendix E – describes 4100-1282 AZF Switch and LED Address mapping. Appendix F – describes useful pseudo points and lists for when working on a 4100U panel, especially when chasing intermittent faults. Before you start To get the job done with the minimum of problems and re-work, get the project specific data sent to you via email or in writing –...
  • Page 10 4100U-S1 Programming Guide Document: LT0400 System Overview THIS PAGE IS INTENTIONALLY BLANK Page 1-4 15 December 2010 Issue 1.4...

  • Page 11: System Overview

    Document: LT0400 4100U-S1 Programming Guide System Overview 2 System Overview Issue 1.4 15 December 2010 Page 2-1...

  • Page 12: General Description

    General Description The 4100U-S1 is a pre-packaged configuration of the well-established 4100U fire alarm system. It is aimed at smaller applications requiring one to four loops of Simplex addressable devices with status and control for up to 64 zones. The 4100U-S1 is available from stock, along with a range of expansion cards and modules, making the 4100U-S1 an off the shelf solution.

  • Page 13: Programming

    Custom control programs 3 – 5 have been produced to ensure the panel behaviour meets Australian standard AS4428.1 and behaves as described. Generally, these should not be modified without consulting with your local Simplex office/dealer unless directed by this or another manual.
  • Page 14 4100U-S1 Programming Guide Document: LT0400 System Overview THIS PAGE IS INTENTIONALLY BLANK Page 2-4 15 December 2010 Issue 1.4...

  • Page 15: About The Programming Tools

    Document: LT0400 4100U-S1 Programming Guide About the Programming Tools 3 About the Programming Tools Issue 1.4 15 December 2010 Page 3-1...

  • Page 16: General

    The installation process will create a directory named after the Programmer‟s version (e.g. Version 12.05.02) under the „C:\Program Files\Simplex\4100U Programmer‟ directory. To launch the programmer click Start | (ALL) Programs | Simplex | the appropriate version number | 4100U Programmer.

  • Page 17: Steps To Configuring A New System

    Document: LT0400 4100U-S1 Programming Guide About the Programming Tools Steps to Configuring a New System The steps to configuring a new system are covered in Sections 4 -10. Section 11 contains details on “building” the configuration and downloading it into the panel. Upgrading an Existing Configuration The configuration must be prepared/edited using a version of the programmer that matches the Panel Exec firmware installed.
  • Page 18 4100U-S1 Programming Guide Document: LT0400 About the Programming Tools THIS PAGE INTENTIONALLY LEFT BLANK Page 3-4 15 December 2010 Issue 1.4...

  • Page 19: Creating A Configuration

    Document: LT0400 4100U-S1 Programming Guide Creating a Configuration 4 Creating a Configuration Issue 1.4 15 December 2010 Page 4-1...

  • Page 20: Creating A New Project File

    Customer = Building owner (if known). o Contractor = Contractor company name. Programmed by - Appropriate fields to be filled in, i.e., if programmed by Simplex we fill in branch name file and phone. If programmed by contractor put in local Simplex contact name (e.g., sales rep).

  • Page 21: Adjusting The Number Of Zone Displays

    Document: LT0400 4100U-S1 Programming Guide Creating a Configuration CPU in the text entry field labelled „CPU #‟, and then click on the „Update Access Codes‟ button. If the CPU Serial number is not known then power up the panel - the CPU Serial Number appears on the initial screens displayed during the panel start-up.
  • Page 22 4100U-S1 Programming Guide Document: LT0400 Creating a Configuration THIS PAGE INTENTIONALLY LEFT BLANK Page 4-4 15 December 2010 Issue 1.4...

  • Page 23: Adding Addressable Devices

    Document: LT0400 4100U-S1 Programming Guide Adding Addressable Devices 5 Adding Addressable Devices Issue 1.4 15 December 2010 Page 5-1...

  • Page 24: Adding Devices To An Sps Addressable Loop

    4100U-S1 Programming Guide Document: LT0400 Adding Addressable Devices Adding devices to an SPS Addressable Loop The 4100U-S1 panel is supplied with one addressable loop. This loop is located on the SPS Power Supply. To add addressable devices to this loop using the programmer follow these steps. Select the HARDWARE Tab Click on the “+”...
  • Page 25 Document: LT0400 4100U-S1 Programming Guide Adding Addressable Devices Select the desired address of the device by clicking on the line. Select the Device type Refer to Section 6.2 for Device type options Select the Point type Refer to Sections 6.2 for Point type options Issue 1.4 15 December 2010...

  • Page 26: Assigning Devices To Zones

    4100U-S1 Programming Guide Document: LT0400 Adding Addressable Devices Enter Custom Label into the Custom Label box The Custom Label is limited to 40 characters. It is recommended that the first characters be the point address, followed by the description of the point location and then lastly the zone number.
  • Page 27 Document: LT0400 4100U-S1 Programming Guide Adding Addressable Devices Scroll down until L261 is reached. L261 = Zone 1 L260+n = Zone n Once the correct List is highlighted press F9 to display the points assigned to this list. The Alarm List Zone should always have at least one point tagged;...
  • Page 28 4100U-S1 Programming Guide Document: LT0400 Adding Addressable Devices Select the MAPNET/IDNet option All available addressable devices (MAPNET, IDNet, etc) will now be listed in the Tag List window. Select the required devices by highlighting the device and pressing the <SPACEBAR>. Two red chevrons “>>”...

  • Page 29: Addressable Device Settings

    Document: LT0400 4100U-S1 Programming Guide Addressable Device Settings 6 Addressable Device Settings Issue 1.4 15 December 2010 Page 6-1...

  • Page 30: Introduction

    (detectors and modules) what device type and what point type should be selected in the 4100U programmer. Other point types should not be used without consulting a Simplex technical representative as most have code associated with them that can activate outputs automatically with no isolate control.

  • Page 31: 4098-9754E Multi-Sensor Photo Heat Detector (Combo)

    Document: LT0400 4100U-S1 Programming Guide Addressable Device Settings 6.2.4 4098-9754E Multi-Sensor Photo Heat Detector (COMBO) Mx-x-0 Parent Point Device Type – Standard Multi-Sensor detector on standard base COMBO – Standard Multi-Sensor detector on Isolator base ICOMBO – Standard Multi-Sensor detector on Sounder base SCOMBO Mx-x-1 1 Sub Point...

  • Page 32: 4090-9001 Supervised Input Iam And 4090-9051 Encapsulated Input Iam

    4100U-S1 Programming Guide Document: LT0400 Addressable Device Settings 6.3.2 4090-9001 Supervised Input IAM and 4090-9051 Encapsulated Input Device Type – Standard setting Point Type – General Fire Point. FIRE – Input used by Custom Control Logic only UTILITY TROUBLE – Input used to indicate a Fault status 6.3.3 4090-9002 Relay IAM Device Type...

  • Page 33: 4090-9119 Relay Iam With Unsupervised Input

    Document: LT0400 4100U-S1 Programming Guide Addressable Device Settings – General Purpose relay RELAY – Fault Relay on until fault cleared TRELAY Mx-x-2 2 Sub Point (T-Sense input) Device Type MTSENSE – Fixed Device type Point Type – General Fire Point FIRE –...

  • Page 34: 4090-9116 Addressable Idnet Isolator

    4100U-S1 Programming Guide Document: LT0400 Addressable Device Settings Device Type – Standard setting MLPTIO Point Type – Standard setting UTILITY Mx-x-1 to Mx-x-4 Sub Points (input) Device Type – Fixed Device type MINPUT Point Type – General Fire Point. FIRE –...

  • Page 35: Idnet Devices Typical Applications

    Document: LT0400 4100U-S1 Programming Guide Addressable Device Settings IDNET Devices Typical Applications The following examples show the programming needed for various ID-Net modules being used in some common applications. IAM – Valve Tamper Monitor 1) At the required address add an IAM, Point type SUPERV, Custom Label - Valve Tamper Monitor.
  • Page 36 4100U-S1 Programming Guide Document: LT0400 Addressable Device Settings TRACK PRI=9,9 M1-7-1 | MRELAY | RELAY | TEST SOLENOID [END OUTPUTS] 9) Create another Custom Control equation, this time for the Print statement on the panel display as follows: [INPUTS] STATUS M1-7-1 | MRELAY | RELAY | TEST SOLENOID [END INPUTS]...

  • Page 37: Adding Zone Displays

    Document: LT0400 4100U-S1 Programming Guide Adding Zone Displays 7 Adding Zone Displays Issue 1.4 15 December 2010 Page 7-1...

  • Page 38: General

    4100U-S1 Programming Guide Document: LT0400 Adding Zone Displays General This chapter describes how to add more zones to the configuration. It applies when an existing 4100U-S1 panel is being upgraded to have more zones and the existing configuration needs to be expanded to control them. Configuring zones for new sites where the configuration is built for the 1 time is described in Chapter 4.
  • Page 39 Document: LT0400 4100U-S1 Programming Guide Adding Zone Displays Click on the “+” sign beside the DISPLAY CARDS option on the Available Hardware window. Drag and drop the 4100-1282 – 8 Pushbuttons/16 Red- Yellow LEDs Icon over the Bay 2 icon. An 8 Pushbuttons/16 red- Yellow LEDs module will be added to the configuration.
  • Page 40 4100U-S1 Programming Guide Document: LT0400 Adding Zone Displays To add the 4100-1288/1289 – F4 64 LED / 64 SW Controller Click on the “+” sign beside the ANUNNCIATOR CARDS option on Available Hardware window. Drag the 4100-1288/1289 – F4 64 LED / 64 SW Controller Icon over to the Bay 2 icon and release.
  • Page 41 Document: LT0400 4100U-S1 Programming Guide Adding Zone Displays Then go to the Point Editing tab and edit the points: On the Switch side, for each point, configure Mode: as PBT and on the LED side configure Mode: for odd addresses as SMPL and for even addresses as ON.

  • Page 42: Modify The Custom Control Equations For The Zones

    4100U-S1 Programming Guide Document: LT0400 Adding Zone Displays Modify the Custom Control Equations for the Zones The simplest method to add more custom control equations for the new displays is to open a 32 or 64 zones template and export the custom control equations for the zones, then from within the original site configuration import these equations.
  • Page 43 Document: LT0400 4100U-S1 Programming Guide Adding Zone Displays  Note: the import process message box may display errors if the hardware configuration does not match the number of zones. E.g., in the case where the hardware configuration modification (see 7.3) included only 48 zones and custom control equations referring to zones 49-64 use undefined points.
  • Page 44 4100U-S1 Programming Guide Document: LT0400 Adding Zone Displays THIS PAGE IS INTENTIONALLY BLANK Page 7-8 15 December 2010 Issue 1.4...

  • Page 45: Adding Expansion Modules

    Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules 8 Adding Expansion Modules Issue 1.4 15 December 2010 Page 8-1...

  • Page 46: General

    4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules General See Installation manual LT0394 Iss1.4 Chapter 2 for Physical requirements of fitting cards in bays. This section describes the procedure to configure the panel with additional modules which may be added to the panel. It describes the concept and method of adding modules by giving detailed examples of 6 cards: IDNet, 6 Supervised Signal Card, 8 Point Monitor Card, 8 Aux Relay Card, 24 Point Graphic Interface and a Dual RS232 printer card.
  • Page 47 Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules Click on the “+” sign beside the INTERFACE option on the Available Hardware window. Drag and drop the 4100-3101 – IDNET 250 Points Icon on to the Bay 2 icon. An IDNET card will be added to the panel configuration.
  • Page 48 4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules Select the desired address for the device. Select the Device type Refer to Section 6.2 for Device type options. Select the Point type Refer to Section 6.2 for Point type options. Page 8-4 15 December 2010 Issue 1.4...

  • Page 49: Adding 4100-4321 Legacy Signal Card

    Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules Enter a Custom Label into the Custom Label text box. The Custom Label is limited to 40 characters. It is recommended that the first characters be the point address, followed by the description of the point location and then lastly the zone number, e.g.
  • Page 50 4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules Double click on the card and in the Card Properties tab adjust its address to be greater than 4, then in the „Card Custom Label:‟ text box, enter a descriptive label. Click the Point Editing tab and record the points‟...

  • Page 51: Adding 4100-5004 8 Point Monitor Card

    Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules Adding 4100-5004 8 Point Monitor Card. The 4100-5004 8 Point Monitor Card provides eight conventional detector or contact closure inputs. There are no restrictions on point types. To add the 4100-5004 8 Point Monitor Card to the panel: Select the HARDWARE Tab.

  • Page 52: Adding 4100-3003 8 Aux Relay Card

    4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules Adding 4100-3003 8 Aux Relay Card. The 4100-3003 8 Aux Relay Card provides eight Single Pole Changeover relays and 8 contact closure inputs (Feedback points). To add the 4100-3003 8 Aux Relay Card to the panel: Select the HARDWARE Tab.

  • Page 53: Adding 4100-0302/1290 24 Point Graphic Interface

    Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules Adding 4100-0302/1290 24 Point Graphic Interface. The 4100-0302 24 Point Graphic Interface provides 24 points that can be configured as inputs or outputs, with no restrictions on point‟s allocation as input or output. To add the 4100--0302 24 Point Graphic Interface to the panel: Select the HARDWARE Tab.

  • Page 54: Adding Legacy Card - 4100-0113 Rs-232/2120 Interface Module

    4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules Adding Legacy Card – 4100-0113 RS-232/2120 Interface Module The 4100-0113 RS-232/2120 Interface Module provides two RS-232-C outputs (Port A and Port B) that can be configured for remote printers, CRT, or as a Computer Port for communications to a remote system (e.g.

  • Page 55: Typical Printer Configuration

    Document: LT0400 4100U-S1 Programming Guide Adding Expansion Modules Click the Port Data… button and select the desired Device Type as in the following example for an 80 column CRT output. Click OK and again for the previous screen. Repeat for Port B (if used) and select the appropriate device type and baud rate, etc.
  • Page 56 4100U-S1 Programming Guide Document: LT0400 Adding Expansion Modules THIS PAGE IS INTENTIONALLY BLANK Page 8-12 15 December 2010 Issue 1.4...

  • Page 57: Custom Control

    Document: LT0400 4100U-S1 Programming Guide Custom Control 9 Custom Control Issue 1.4 15 December 2010 Page 9-1...

  • Page 58: General

    4100U-S1 Programming Guide Document: LT0400 Custom Control General 4100U Custom Control equations provide a way to override the 4100U‟s default operation. Each Custom Control equation has a similar form: one half of the equation, called the input side, is used to monitor the state of specific system inputs (initiating devices, for example). The other half of the equation, called the output side, is used to control specific system outputs (relays, addressable devices, etc.).
  • Page 59 Document: LT0400 4100U-S1 Programming Guide Custom Control OR Operator. The OR operator allows you to put a group of points in parallel, meaning the activation of any one or more of the points causes the output side of the equation to execute.

  • Page 60: Creating A New Equation

    4100U-S1 Programming Guide Document: LT0400 Custom Control Creating a New Equation 9.3.1 Select User Program The first step in defining a new custom control equation is to add the equation to either one of the five User Programs -- Program 3 through Program 7. However, it is recommended that Program 6 is used for general functions and Program 7 is used for AS1668 Fan Controls.

  • Page 61: Add Input Statements

    Document: LT0400 4100U-S1 Programming Guide Custom Control 9.3.2 Add Input Statements The second step in creating a new Custom Control equation is to add input statements to the equation. Repeat the steps in this section until all input statements in the equation have been defined.

  • Page 62: Add Output Statements

    4100U-S1 Programming Guide Document: LT0400 Custom Control 9.3.3 Add Output Statements The third step in creating a new Custom Control equation is to add output statements to the new equation. Repeat the steps in this section until all output statements in the equation have been defined.

  • Page 63: Output Statements: Hold Vs. Track

    Document: LT0400 4100U-S1 Programming Guide Custom Control 9.3.4 Output Statements: Hold Vs. Track The 2 commonly used output opcodes are Hold and Track. The main difference is that a Hold command is evaluated only when the inputs side of the equation goes True (on the transition from false to true).
  • Page 64 4100U-S1 Programming Guide Document: LT0400 Custom Control THIS PAGE IS INTENTIONALLY BLANK Page 9-8 15 December 2010 Issue 1.4...

  • Page 65: As1668 Fan Controls

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10 AS1668 Fan Controls Issue 1.4 15 December 2010 Page 10-1...

  • Page 66: Typical Arrangement For As1668 Fan Control

    4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls 10.1 Typical Arrangement for AS1668 Fan Control The following scheme illustrates a typical topology using the AS1668 Fan Control Module. Note: AS1668.1 recommends that the duct detector be downstream from the fan, before the first branch in the ducts –...

  • Page 67: As1668 Fan Control Flows

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10.2 AS1668 Fan Control Flows The control of ventilation and air conditioning in buildings under fire mode is described in AS/NZS 1668.1:1998. This requires fire alarm detection to activate the fan to prevent the smoke from spreading to other zones.
  • Page 68 4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls AS1668 Fan Manual Stop: 1. The 4100U-S1 panel receives indications from its AS1668 board that Fan #n rotary switch state has changed to „Stop‟. 2. The 4100U-S1 panel commands the Multi-Point I/O to open the relay that controls the fan to stop.

  • Page 69: As1668 Fan Control State Table

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10.3 AS1668 Fan Control State Table The following table shows how the airflow input is reflected on the AS1668 red and green LEDs. Airflow AS1668 Input Green and Red LEDs Red ON Green OFF Green ON Red OFF...

  • Page 70: As1668 Fan Control Card Programming

    4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls 10.4 AS1668 Fan Control Card Programming The 4100U-S1 can be installed with an ME0456 AS1668 fan control module which is programmed as a 4100-1284 8 x Button and 16 x LED module. Follow the 4100-1284 programming as described in Section 7.3, except for the Point Editing tab which differs from the standard zone programming and is described here.

  • Page 71: Led Configuration

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10.4.2 LED Configuration The LEDs configuration couples the Red Amber and Green LEDs of each fan to a pseudo point. Each fan uses 4 LEDs: LED 1 set = Red LED is ON = Fan is running. LED 2 set = Amber LED is ON = Fan is faulty.

  • Page 72: Point Editing

    4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls 10.4.3 Point Editing Click the Point tab and scroll to point P1265 which is coupled to the Fault LED of the 1 fan. Configure the points as described hereafter for the 1 fan: Click on the line and select the Point Type TROUBLE.

  • Page 73: As1668 Custom Control Equations

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10.5 AS1668 Custom Control Equations The control of the fans and the AS1668 LEDs as described in Section 10.2 is done using custom control equations in custom control program 7: AS1668 FAN CONTROL CUSTOM CONTROL.

  • Page 74: Set Up Register

    4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls 10.5.2 Set up Register 8 The state of P516 is stored in register 8 and is used in the S/A Detector Isolate and De- Isolate equations. [INPUTS] NOT STATUS ON P516 | DIGITAL | UTILITY | ALARM OR FAULT TEST ACTIVE SAVE 8 [END INPUTS] [OUTPUTS]...

  • Page 75: S/A Detector Active

    Document: LT0400 4100U-S1 Programming Guide AS1668 Fan Controls 10.5.5 S/A DETECTOR ACTIVE The S/A detector is added to the zone list. This equation uses negative logic - all operations are triggered when the S/A Detector is not active - it has cleared of smoke. This is followed by the restart delay OR if the detector is isolated.

  • Page 76: Fan Fault Conditions

    4100U-S1 Programming Guide Document: LT0400 AS1668 Fan Controls 10.5.8 FAN fault conditions This equation sets the amber LED (fault) to ON when the fan control relay is set to operate the fan but the airflow indicator does not report that air is flowing, when the fan control relay is set to stop the fan but the airflow indicator reports that air is flowing or a fault signal is received from the Mechanical Services Board.

  • Page 77: Building And Downloading The Configuration

    Document: LT0400 4100U-S1 Programming Guide Building and Downloading the Configuration 11 Building and Downloading the Configuration Issue 1.4 15 December 2010 Page 11-1...

  • Page 78: General

    If errors are detected by the build operation, they are flagged and the build operation aborts. These errors must be resolved before the build can be performed and the CFIG can be created. Contact Simplex Service Support for help in resolving build errors. Start the programmer and open the job that you want to build.

  • Page 79: Starting The Transfer Utility

    Start button. Move the pointer to the Programs option. When the list of choices appears, move the pointer to the Simplex option and click on the option containing the appropriate programmer (for example, 4100U Ver 11.01.01. A list of options appears.

  • Page 80: Direct Connection To The Panel

    4100U-S1 Programming Guide Document: LT0400 Building and Downloading the Configuration 11.4 Direct Connection to the Panel Follow these steps to connect the 733-794 serial cable between the PC and the panel. 1. Locate the PC within 6 feet of the panel and connect a 733-794 serial cable to the configured serial port (typically COM1) on the PC.

  • Page 81: Uploading From The Panel

    Document: LT0400 4100U-S1 Programming Guide Building and Downloading the Configuration Click the Download… button. A dialog as follow appears: Click the Start button to begin the download. The display on the front panel of the 4100U shows the progress of the download, and notifies when the download is complete.

  • Page 82: Sending 4100U Files To Simplex

    The folder can normally be found under C:\4100Ujobs\. If you have uploaded a config from a 4100U Panel, it must be sent to Simplex, so it can be de-compiled into an editable format. After conversion, Simplex will send you the editable files.

  • Page 83: Appendices

    Document: LT0400 4100U-S1 Programming Guide Appendices 12 Appendices Issue 1.4 15 December 2010 Page 12-1...

  • Page 84: Appendix A - As4428.1 Operation

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.1 Appendix A – AS4428.1 Operation A 4100U-S1 that is required to comply with AS 4428.1 needs special functionality to be implemented. This is done by a number of custom control equations. Program 3 contains the system functions to provide brigade relay operation, common front panel controls, battery testing and AVF.

  • Page 85: Appendix B - Common Variables And Custom Control

    Document: LT0400 4100U-S1 Programming Guide Appendices 12.2 Appendix B - Common Variables and Custom Control The following explains Points and Lists that are used in the AS 4428.1 Custom Control Logic. These Points and Lists may also be used in other custom control equations not listed below.

  • Page 86: Analog Points

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.2.2 Analog Points Analog Points can have a value 0-65535 and can be used for Timers, Counters or store a numerical value. A0 – Number of Devices in Alarm A1 – Number of Isolates A2 –...

  • Page 87: Battery Test

    Document: LT0400 4100U-S1 Programming Guide Appendices 12.2.5 Battery Test The battery is automatically tested at 8:00:03 every Tuesday morning according to the internal clock. The test runs for 1 hour (plus 5 seconds). The battery test is disabled if any Alarm is present or an Alarm occurs during the battery test. Manual battery tests can be started by activating P520.

  • Page 88: Brigade Relay Equations

    P478 | DIGITAL | UTILITY | INHIBIT DEVICE TROUBLES WHILE DISABLED [END OUTPUTS 12.2.7 Brigade Relay Equations The following are the equations used to drive the Alarm, Isolate and Fault Brigade Relays. These equations should not be modified without consulting a Simplex Technician. References: Point Address: 0-7-3...
  • Page 89 Document: LT0400 4100U-S1 Programming Guide Appendices 3-3 ASE Fault Relay [INPUTS] STATUS ON A2 | ANALOG | ANALOG | NUMBER OF SYSTEM TROUBLES [END INPUTS] [OUTPUTS] TRACK ON PRI=7,7 0-7-4 | MCODE7 | RELAY | Master Output - City Trouble Relay TRACK ON PRI=7,7 1-12 | SPECOUT | SPECOUT | CITY TBL/OPT RELAY 3 [END OUTPUTS]...

  • Page 90: Appendix C - Custom Control For Control Keys And Indicators

    Custom Control equations to meet AS 4428.1 requirements. These equations are part of Program 3. They should not be changed, except under the direction of Simplex Fire Products, since the operation of the panel may be adversely affected.

  • Page 91: Common Zone Alarm Led

    Document: LT0400 4100U-S1 Programming Guide Appendices 12.3.1 Common Zone Alarm LED This Red LED flashes if any Zone is in alarm and is not acknowledged. The LED is on steady if any Zone is in Alarm and all Alarms are acknowledged. The LED is off when there are no Zones in Alarm.

  • Page 92: Alarm / Fault / Normal Test Button And Leds

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.3.2 Alarm / Fault / Normal Test Button and LEDs This button is used to select between Alarm Test, Fault Test and Normal operation for the Multifunction buttons. The Alarm Test and Fault Test LEDs indicate what operation the Multifunction buttons will initiate if pressed.
  • Page 93 Document: LT0400 4100U-S1 Programming Guide Appendices 3-14 Alarm and Fault Test Mode OFF [INPUTS] STATUS ON P513 | DIGITAL | UTILITY | ALARM TEST/FAULT TEST/NORMAL BUTTON AND STATUS ON P515 | DIGITAL | UTILITY | FAULT TEST [END INPUTS] [OUTPUTS] HOLD OFF PRI=9,9 P515 | DIGITAL | UTILITY | FAULT TEST HOLD OFF PRI=9,9...

  • Page 94: Example Alarm And Fault Test Equations

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.3.3 Example Alarm and Fault Test equations These equations (with point number modifications) must be included for each zone to carry out the zone alarm or fault test when the zone button is pressed and alarm or fault test modes are active.

  • Page 95: Bells Isolate Led And Button

    Document: LT0400 4100U-S1 Programming Guide Appendices 4.4 ACF Isolate LED and Button The ACF Isolate LED indicates that the General Fire Trip List is Isolated. Pressing the ACF Isolate button toggles the isolation of this list. References set to “TOF” Mode Push Button Mode Point Address: 0-5-3 ACF Isolate Button...

  • Page 96: Warning System Isolate

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.3.6 Warning System Isolate The Warning System Isolate LED indicates that the Warning System Output is Isolated. Pressing the Warning System Isolate button toggles the isolation of the output. SIG5 (NAC 3) on the SPS is activated when an alarm is present and the warning system is not isolated.
  • Page 97 Document: LT0400 4100U-S1 Programming Guide Appendices Reset zone isolate toggle This equation handles the toggling of the Isolate pushbuttons for each zone. A point in list 260 is set on any Isolate pushbutton being depressed so that only one action is carried out on the push of the button.

  • Page 98: Appendix D - Custom Control For Alarm Zone Facilities

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.4 Appendix D - Custom Control for Alarm Zone Facilities A 4100-1282 8 Pushbutton/8 red LED/8 amber LED module is fitted for each 8 zones to display the alarm and isolate states of the zones (lists) and allow the zone to be isolated, alarm tested or fault tested.

  • Page 99: Lists

    Document: LT0400 4100U-S1 Programming Guide Appendices 12.4.2 Lists Zone 1 – Zone 1 Alarm List L261 – Zone 2 Alarm List L262 … – Zone n Alarm List L260+n 12.4.3 Switches and LEDs Zone 1 – Zone 1 Multifunction Switch 3-65 –...

  • Page 100: Zone N Equations

    4100U-S1 Programming Guide Document: LT0400 Appendices 4-5 ZONE 1 New Alarm and LED Flash [INPUTS] CONTINUE AND STATUS FALMACK L261 | LIST | MIXED | ALARM LIST ZONE 1 [END INPUTS] [OUTPUTS] FLASH SLOW 3-1 | LED | LED | AZF1 LED TRACK ON PRI=9,9 P512 | DIGITAL | UTILITY | A ZONE ALARM LED IS FLASHING [END OUTPUTS]...
  • Page 101 Document: LT0400 4100U-S1 Programming Guide Appendices ZONE n Isolate [INPUTS] STATUS FIRE L260+n | LIST | MIXED | ALARM LIST ZONE n AND NOT STATUS ON P600+n | DIGITAL | SUPERV | ISOLATE ZONE n [END INPUTS] [OUTPUTS] TRACK ON PRI=9,9 P800+n | DIGITAL | UTILITY | ALARM ZONE n [END OUTPUTS] ZONE n New Alarm and LED Flash...

  • Page 102: Appendix E - 4100-1282 Azf Switch And Led Address Mapping

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.5 Appendix E - 4100-1282 AZF Switch and LED Address Mapping The following table displays the fixed mapping of zones to Display modules (using 4100- 1282) with HW Ref Addresses of the Push-Buttons, the Alarm LEDs and the Isolate LEDs, and their matching Pseudo Points.
  • Page 103 Document: LT0400 4100U-S1 Programming Guide Appendices P941 P641 4-73 4-17 4-18 P942 P642 4-74 4-19 4-20 P943 P643 4-75 4-21 4-22 P944 P644 4-76 4-23 4-24 P945 P645 4-77 4-25 4-26 P946 P646 4-78 4-27 4-28 P947 P647 4-79 4-29 4-30 P948 P648...

  • Page 104: Appendix F - Useful Pseudo Points And Lists

    4100U-S1 Programming Guide Document: LT0400 Appendices 12.6 Appendix F – Useful Pseudo Points and Lists The following tables list System Digital Pseudo points, System Analog Pseudo points and System Lists that are useful when working on a 4100U panel, especially when chasing intermittent faults.
  • Page 105 Document: LT0400 4100U-S1 Programming Guide Appendices System Lists Point Label GENERAL FIRE ALARM MONITOR ZONES Stores the number of physical alarm type points connected to the panel. VARIABLE SENSITIVITY PHOTO ANALOG SENSOR Stores the number of TrueAlarm Photo detectors connected to the panel.
  • Page 106 4100U-S1 Programming Guide Document: LT0400 Appendices THIS PAGE IS INTENTIONALLY BLANK Page 12-24 15 December 2010 Issue 1.4...

Table of Contents