Simplex 4100ES Quick Start Manual

UL, ULC, CSFM Listed; FM Approved;
MEA (NYC) Acceptance*
Features
Master Controller (top) bay:
 32-Bit Master Controller with color-coded operator
interface including raised switches for high confidence
feedback
 Dual configuration program CPU, convenient service port
access, and capacity for up to 2000 addressable points
 CPU assembly includes 2 GB dedicated compact flash
memory for on-site system programming and
information storage
 System power supply (SPS) and charger (9 A total) with
on-board: NACs, IDNet addressable device interface,
programmable auxiliary output and alarm relay
 Available with InfoAlarm Command Center expanded
content user interface (see data sheet S4100-0045)
 Upgrade kits are available for existing control panels
Standard addressable interfaces include:
 IDNet addressable device interface with 250 points that
support TrueAlarm analog sensing and operate with
either shielded or unshielded twisted pair wiring
 Remote annunciator module support via RUI (remote
unit interface) communications port
Optional modules include:
 Building Network Interface Module (BNIC) for Ethernet
connectivity options (see data sheet S4100-0061)
 TrueAlert addressable notification appliance power
supplies with three, 3 A SLC outputs
 Additional IDNet and MAPNET II addressable device
modules and IDNet/MAPNET II quad isolator modules
 IDNet+ output module with built-in quad isolator and
enhanced operation for better retrofit to existing wiring
(see data sheet S4100-0046)
 Fire Alarm Network Interfaces, DACTs, city
connections, and up to five (5) RS-232 ports for printers
and terminals
 IP communicator compatibility
 Alarm relays, auxiliary relays, additional power
supplies, IDC modules, NAC expansion modules
 Service modems, VESDA Air Aspiration Systems
interface, ASHRAE BACnet Interface, TCP/IP Bridges
 LED/switch modules and panel mount printers
 Emergency communications systems (ECS) equipment;
8 channel digital audio or 2 channel analog audio
 Battery brackets for seismic area protection (see page 2)
Compatible with Simplex
 4009 IDNet NAC Extenders, up to ten per IDNet SLC
 TrueAlert Addressable Controllers
4100ES and upgrade kits are UL Listed to:
 UL Std. 864, Fire Detection and Control (UOJZ), and
Smoke Control Service (UUKL)
 UL Std. 2017, Process Management Equipment (QVAX)
 UL Std. 1076, Proprietary Alarm Units-Burglar (APOU)
 UL Std. 1730, Smoke Detector Monitor (UULH)
 ULC Std. S527-99
®
remotely located:
Fire Control Panels
Addressable Fire Detection and Control
Basic Panel Modules and Accessories
Emergency Operating Instructions
A B C D E F G H I
1 ZONE 2 SI G A UX 3
J K L FB M N O IO P Q R I DNet
4 5 6
Fire Alarm ALARMS Priority 2 Alarm Supervisory SYSTEM WARNINGS Trouble Ala rm Silenced AC Power
S T U P V W X A Y Z / L
7 8 9
Fire Alarm Priority 2 Supv Tr ouble Alar m System 'SP ' ( ) , 0 :
Ack Ack Ack Ack Silence Reset N ET ADDR DE L
0
Enter C/Exit
Event Time Info More
Previous
Menu
Enable On Arm Next
Off Lamp
Disable Disarm Auto Test
Emergency Operating Instructions
Alarm or Warning Condition How t o Silence Building Signals
System ind icator flashing. Tone On. Press Alarm Silence.
How to Acknowledge / View Events How t o Reset System
Press ACK l ocated under fl ashin g indi cator. Press System Reset.
Local tone wil l silence. Repeat operation unti l al l events are acknowledged. Press Ack to si lence tone device.
4100ES Cabinets are Available with
One, Two or Three Bays
Software Feature Summary
CPU provides dual configuration programs:
 Two programs allow for optimal system protection and
commissioning efficiency with one active program and
one reserve
 Downtime is reduced because the system stays running
during download
PC based programmer features:
 Convenient front panel accessed Ethernet port for quick
and easy download of site-specific programming
 Modifications can be uploaded as well as downloaded
for greater service flexibility
 AND, firmware enhancements are made via software
downloads to the on-board flash memory
Introduction
4100ES Series Fire Detection and Control Panels
provide extensive installation, operator, and service features
with point and module capacities suitable for a wide range of
system applications. An on-board Ethernet port provides fast
external system communications to expedite installation and
service activity. Dedicated compact flash memory archiving
provides secure on-site system information storage of
electronic job configuration files to meet NFPA 72 (National
Fire Alarm and Signaling Code) requirements.
Modular design. A wide variety of functional modules
are available to meet specific system requirements.
Selections allow panels to be configured for either
Stand-Alone or Networked fire control operation. InfoAlarm
Command Center options provide convenient expanded
display content (detailed on data sheet S4100-0045).
* See pages 5 and 6 for product that is UL or ULC listed and additional listing information.
This product has been listed by the California State Fire Marshal (CSFM) pursuant to
Section 13144.1 of the California Health and Safety Code. See CSFM Listing
7165-0026:251(4100ES) and 7300-0026:0368 (4009 TPS) for allowable values and/or
conditions concerning material presented in this document. It is subject to re-examination,
revision, and possible cancellation. Accepted for use – City of New York Department of
Buildings – MEA35-93E. Additional listings may be applicable; contact your local Simplex
product supplier for the latest status. Listings and approvals under Simplex Time Recorder
Co. are the property of Tyco Fire Protection Products.
ZONE A B C D E F SI G A UX G H I
1 2 3
FB J K L IO M N O P Q R I DNet
ALARMS SYSTEM WARNINGS AC Power 4 5 6
Fire Alarm Priority 2 Ala rm Supervisory Trouble Alar m Silenced S T U V W X Y Z /
P A L
7 8 9
Fire Alarm Priority 2 Supv Trouble Alarm System 'SP' ( ) , 0 :
Ack Ack Ack Ack Silence Reset NET 0 ADDR DEL
Event Mor e Enter C/Exit
Time Info Previ ous
Menu
On
Enable Arm Next
Disable Off Auto Lamp
Disarm Test
Alarm or Warning Condition How to Silence Building Signals
System indi cator flashing. Tone On. Press Alarm Silence.
How to Acknowledge / View Events How to Reset Syst em
Press ACK located under flashing indicator. Press System Reset.
Repeat operation until all events are acknowledged. Press Ack to si lence tone device.
Lo cal to ne will silence.
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
S4100-0031-21 12/2012