English ( Original Instructions ) - Luna BDS 300B Manual

ENGLISH
Original instructions
Save these instructions
Additional safety rules for the disc sander
1. Never stand or have an observer stand in line with
the abrasive disc.
2. Work area should have adequate light and surroun-
ding work space should be clear.
3. the disc sander is intended for indoor use only.
4. Always wear eye protection and during extended
operation use ear protection.
5. Always avoid awkward hand positions, where a
sudden slip could cause a hand to move into the abra-
sive disc.
6. Use the proper size and type of sanding disc for
each operation.
7. Turn the machine OFF before removing scrap pie-
ces form the table. Never turn the sander ON before
clearing the tables or work surfaces of all objects
(tools, wood scrape, etc.) except for the work piece
and related feed or support devices for the operation
planned.
8. Be certain the abrasive disc runs in the right direc-
tion before beginning the disc.
9. Hold work firmly so that it will not be pulled from
your hands when finishing against the disc.
10. Feed material gradually. Do not force the machine
to remove material faster than it was designed to sand.
11. Do not attempt to sand pieces too small to hold
safely by hand.
12. When sanding a large workpiece, make sure it is
properly supported at table height.
13. Never leave the machine work area with the po-
wer on, or before the machine has come to a complete
stop.
14. If any part of the disc sander should break or da-
maged, or any electrical component fail to perform
properly, or if any part is missing, immediately shut
off power switch, remove cord from power supply
and replace damaged or missing part before resuming
operation.
15. Always support workpiece with backstop or work-
table.
16. Maintain 0,16 mm maximum clearance between
table and sanding disc.
17. Use only the motor supplied with your sander.
18. FIRE CAUTION: This machine is not designed
for heavy deburring operations. However, when finis-
hing ferrous metals, spark will be generated and could
cause a fire. To prevent this possibility, remove dust
collecting apparatus. Remove all traces of wood dust
that may have accumulated in and around the machi-
ne. Also, the mixing of ferrous and nonferrous metal
dust can create a hazardous environment.
19. Use sander in a well ventilated area.
Specifications
Art. No. .......................................................................
Luna ............................................................................
Disc Diameter ...................................................... mm
Table Tilt .....................................................................
Table Size ............................................................ mm
Disc Speed ........................................................... rmp
Disc Brake ...................................................................
Motor.......................................................................W
Volts .........................................................................V
Net Weight ..............................................................kg
Sound level ...................................................... dB(A)
GROUNDING
In the event of a malfunction or breakdown, groun-
ding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool
is equipped with an electric cord having an equipment
grounding conductor and a grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
OPERATION
Be sure your power supply agrees with the name
plate marking of Voltage and Frequency. A voltage
decrease or more than 10%will cause a loss of power
and overheating. All tools are factory tested. If this
tool does not operate, check the power supply.
This product is made to the highest possible standards.
Designed to facilitate the precision sanding of radial,
curves, bevels and chamfers on wood, plastics, metals
and ceramics. It is fully guaranteed and suitable for
both industrial and D.I.Y use. If you use correctly, it
will give many years of trouble free service in either
factory, workshop or home wherever a combination
of high performance are required.
INSTRUCTIONS
1. After unpacking the unit fit the work-table to its
mountings by means of the two 1/4" bolts and was-
hers/spacers provided locating it with the two 1/4"
studs which allow the table to swivel. Make sure it at
there is a clearance of 1.6mm between the table and
the face of the sanding disc, in accordance with dia-
gram A.
2. The table may be set at any angle of depression
from 0-45. To lower the table, unlock the 6 bolts se-
curely to lock the table in position. Next, fit the mitre
gauge, if required, by sliding it into the groove pro-
vided on the work-table. To vary angle, unlock the
1/4nut and set according to the scale.
3. If desired, the rubber suction pad supports on the
12
20009-0207
BDS 300B
305
45° Down
446 x 156
1400
Manual
550
230
36
≤ 87