Table of Contents
Advertisement
This will take some time. Please wait ...
Note : If you see the following failure message, ignore the message, the active Supervisor-1 Module
will bring up the standby Supervisor-4 Module to HA-standby supervisor state in some time.
2019 Jun 25 15:15:06 switch %SYSMGR-2-STANDBY_BOOT_FAILED:
Standby supervisor failed to boot up.
8. System will automatically do a copy running-config to startup-config.
The following message is displayed:
<Tue Jun 25 15:15:33 2019> Saving configuration now. Please wait ...
[########################################] 100%
Copy complete.
/mnt/plog/migration.log: 2.91 kB 74.67 kB/s
<Tue Jun 25 15:15:46 2019> Supervisor-1 will switchover to Supervisor-4
<Tue Jun 25 15:15:47 2019> Switchover is successful,
Supervisor-4 is now active
9. Once the standby module comes online, a system switchover happens and the new Supervisor-4
Module becomes the current active supervisor. This process moves the Supervisor-4 Module from the
HA-standby mode to active mode. The SSH/telnet session is disconnected during the switchover. You
have to reconnect to the SSH/telnet session. Also, ensure that the console link and the management
link are connected to the newly inserted Supervisor-4 Module.
The following syslog message is displayed on the active Supervisor-4 Module:
Supervisor-4 Module syslogs
2019 Jun 25 15:15:47 switch %SYSMGR-2-HASWITCHOVER_PRE_START:
This supervisor is becoming
active (pre-start phase).
2019 Jun 25 15:15:48 switch %SYSMGR-2-HASWITCHOVER_START:
Supervisor 6 is becoming active.
2019 Jun 25 15:15:48 switch %IPS-5-IPS_MGR_FEATURE_ENABLE:
Restore cond runtime ips:0
iscsi:0 fcip:0 iscsi-intf-vsan:0 ips-lc:1
2019 Jun 25 15:15:48 switch %ASCII-CFG-6-INFORMATION:
Reading ACFG Runtime information
2019 Jun 25 15:15:48 switch %SYSMGR-2-SWITCHOVER_OVER:
Switchover completed.
2019 Jun 25 15:15:48 switch %PLATFORM-1-PFM_ALERT:
Disabling ejector based shutdown on
sup in slot 6
2019 Jun 25 15:15:50 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_STARTED:
Setting boot parameters for supervisor migration process.
It might take some time.
Please do not set any config parameters during this time.
2019 Jun 25 15:15:52 switch %PLATFORM-2-SUP_UNSUPPORTED:
Unsupported card detected in
supervisor slot 5 powered down
2019 Jun 25 15:15:52 switch %PLATFORM-2-MOD_PWRDN:
Module 5 powered down (Serial number )
2019 Jun 25 15:15:52 switch %PLATFORM-5-MOD_STATUS:
Module 5 current-status is
MOD_STATUS_CONFIGPOWERED_DOWN
2019 Jun 25 15:15:53 switch %PLATFORM-5-MOD_STATUS:
Module 5 current-status is
MOD_STATUS_POWERED_DOWN
Note : The old active Supervisor-1 Module will be powered down. The supervisor Status LED will
be blinking red, when the supervisor module is powered down by the migration command. If the
Status LED is not blinking red, then check the migration status using the show logging onboard
migration status command on any management session.
10. After the successful completion of the system switchover, the following syslog message is displayed:
2019 Jun 25 15:16:39 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_COMPLETE:
Migration process is complete now.
Supervisor-3 in standby slot can now be replaced with Supervisor-4.
2019 Jun 25 15:18:00 switch %SYSMGR-2-SBY_SUP_LESS_MEMORY_SLOT:
Supervisor in slot 6 is running with less memory than
active supervisor in slot 5
2019 Jun 25 15:18:00 switch %SYSMGR-2-CONVERT_STARTUP_ABORTED:
Conversion of startup-config failed.
2019 Jun 25 15:18:00 switch %PLATFORM-2-MOD_PWRDN: Module 6 powered down
(Serial number JAE17440HVB)
96 IBM Storage Networking SAN192C-6, SAN384C-6 and SAN768C-6: SAN192C-6, SAN384C-6 and
SAN768C-6 Installation, Service, and User Guide
Advertisement
Table of Contents
