Related Manuals for Teknik Stationmaster 5426454
Summary of Contents for Teknik Stationmaster 5426454
- Page 1 Teknik For all your newfangled gadgetry. Stationmaster L-Shaped Desk Model 5426454...
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identification Assembly Steps 6-28 Français 29-32 Español 33-36 Safety 37-38 Warranty Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
- Page 3 Now you know Part Identification our ABCs. Page 3...
- Page 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) WIDE EXTENSION WIDE EXTENSION NARROW EXTENSION NARROW EXTENSION RAIL - 2 SLIDE - 2 RAIL - 2 SLIDE - 2 WIDE WOOD CAM SCREW - 14 HIDDEN CAM - 14...
-
Page 5: Table Of Contents
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 2-1/3" HEX HEAD SCREW - 8 1-9/16" PAN HEAD SCREW - 4 1-9/16" HEX HEAD SCREW - 2 1-3/16" FLAT HEAD SCREW - 12 1"... - Page 6 Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL NOTE: Various CAM SCREWS or a CAM DOWEL may be used. Turn the CAM SCREW or gently tap the CAM DOWEL until the shoulder is against the surface of the part.
- Page 7 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Some assembly å Turn four CAM SCREWS (5) into the SHELF (A). (and snacks) required. å Push four HIDDEN CAMS (6) into the UPRIGHT (C) and RIGHT END (D).
- Page 8 Step 2 å Separate the WIDE EXTENSION SLIDES (4) from the WIDE EXTENSION RAILS (3) as shown in the diagram below. Be prepared, the parts are greasy. å Separate the NARROW EXTENSION SLIDES (2) from the NARROW EXTENSION RAILS (1) as shown in the diagram below.
- Page 9 Step 3 å Insert four WIDE WOOD DOWELS (7) into the SHELF (A). å Fasten the SHELF (A) to the UPRIGHT (C) and RIGHT END (D). Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the SHELF insert into the holes in the UPRIGHT and RIGHT END.
- Page 10 Step 4 å Insert four WIDE WOOD DOWELS (7) into the BACK (E). å Insert the WOOD DOWELS in one edge of the BACK (E) into the SHELF (A) (4 used) Page 10...
- Page 11 Step 5 å Insert four WIDE WOOD DOWELS (7) into the UPRIGHT (C) and RIGHT END (D). å Fasten the BOTTOM (B) to the UPRIGHT (C) and RIGHT END (D). Use four 1-9/16" PAN HEAD SCREWS (17). å NOTE: Be sure the WOOD DOWELS in the UPRIGHT, RIGHT END, and BACK (E) insert into the holes in the BOTTOM.
-
Page 12: 2-1/3" Hex Head Screw
Step 6 å Insert two HIDDEN CAMS (6) into the SMALL MODESTY PANEL (U). å Fasten the LEG (V) to the SMALL MODESTY PANEL (U). Tighten two 2-1/3" HEX HEAD SCREWS (15) using the L-WRENCH (14). 2-1/3" HEX HEAD SCREW (2 used in this step) Curved edge Page 12... - Page 13 Step 7 å Carefully stand your unit upright. å Fasten the SMALL MODESTY PANEL (U) to the UPRIGHT (C). Tighten two 2-1/3" HEX HEAD SCREWS (15) using the L-WRENCH (14). 2-1/3" HEX HEAD SCREW (2 used in this step) Page 13...
- Page 14 Step 8 å Insert four HIDDEN CAMS (6) into the LARGE MODESTY PANEL (T). å Fasten the LEFT END (W) to the LARGE MODESTY PANEL (T). Tighten two 2-1/3" HEX HEAD SCREWS (15) using the L-WRENCH (14). Curved edge 2-1/3" HEX HEAD SCREW (2 used in this step) Page 14...
- Page 15 Step 9 å Fasten the LARGE MODESTY PANEL (T) to the LEG (V). Tighten two 2-1/3" HEX HEAD SCREWS (15) using the L-WRENCH (14). 2-1/3" HEX HEAD SCREW (2 used in this step) Page 15...
- Page 16 Step 10 å First, fasten the BRACE (X) to the SMALL MODESTY PANEL (U). Tighten one 1/2" HEX HEAD SCREW (23) using the L-WRENCH (14). å Then, fasten the BRACE (X) to the LEFT END (W). Tighten one 1" HEX HEAD SCREW (19) using the L-WRENCH (14). 1/2"...
- Page 17 Step 11 å NOTE: Position parts exactly as shown. å Turn six CAM SCREWS (5) into the TOPS (R and S). Page 17...
-
Page 18: 1-9/16" Hex Head Screw
Step 12 å NOTE: You should start each SCREW a few turns before completely tightening any of them. å Fasten the TOPS (R and S) to the MODESTY PANELS (T and U). Tighten six HIDDEN CAMS. å Fasten the SMALL TOP (S) to the LEFT END (W). Tighten two 1-9/16" HEX HEAD SCREWS (17) using the L-WRENCH (14). - Page 19 Step 13 å Fasten the TIE PLATE (12) to the TOPS (R and S). Use four 9/16" PAN HEAD SCREWS (22). Now might be a good time to refresh your drink. 9/16" PAN HEAD SCREW (4 used in this step) Page 19...
- Page 20 Step 14 å Turn four CAM SCREWS (5) into the SMALL DRAWER FRONT (F). å Push four HIDDEN CAMS (6) into the SMALL DRAWER SIDES (G and H). Page 20...
- Page 21 Step 15 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Groove U n fi n i s h s u r f a c BLACK 1-3/16" FLAT HEAD SCREW (4 used in this step) å...
-
Page 22: 13/16" Machine Screw
Step 16 å Fasten a KNOB SET (11) to the SMALL DRAWER FRONT (F). Use one 13/16" MACHINE SCREW (21). å Fasten the NARROW EXTENSION SLIDES (2) to the SMALL DRAWER SIDES (G and H). Use six 1/2" FLAT HEAD SCREWS (24). å... -
Page 23: 1-3/16" Flat Head Screw
Step 17 å Insert four THIN WOOD DOWELS (8) into the holes shown in the LARGE DRAWER BACK (O) and DRAWER BOX FRONT (P). å Fasten the LARGE DRAWER SIDES (M and N) to the LARGE DRAWER BACK (O) and DRAWER BOX FRONT (P). Use eight 1-3/16"... - Page 24 Step 18 å Slide the LARGE DRAWER BOTTOM (Q) into the grooves in the LARGE DRAWER SIDES (M and N) and LARGE DRAWER BACK (O). å Carefully flip the drawer over. å Press the FILE GLIDES (9) onto the edges of the LARGE DRAWER BACK (O) and DRAWER BOX FRONT (P).
-
Page 25: 1" Pan Head Screw
Step 19 å Insert four THIN WOOD DOWELS (8) into the LARGE DRAWER SIDES (M and N). å Fasten the LARGE DRAWER FRONT (L) to the DRAWER BOX FRONT (P). Use four 1" PAN HEAD SCREWS (20). 1" PAN HEAD SCREW (4 used in this step) (4 used) Groove... -
Page 26: 1/2" Flat Head Screw
Step 20 å Fasten the WIDE EXTENSION SLIDES (4) to the LARGE DRAWER SIDES (M and N). Use six 1/2" FLAT Almost time to HEAD SCREWS (24). celebrate! With a nap. å NOTE: Use the exact holes shown. Open end Open end 1/2"... - Page 27 Step 21 å To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.
- Page 28 Step 22 å Peel APPLIQUES from the APPLIQUE CARDS (13) and stick them onto each visible HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. 35 lbs.
- Page 29 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...