Related Manuals for Teknik 5426484
Summary of Contents for Teknik 5426484
- Page 1 Sit and surf. Executive Desk NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Elstree | Model 5426484 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 6-40 Hammer Not actual size Français 41-46 Español 47-52 Adjustable Wrench Safety 53-54 Tape Measure Warranty Part Identifi cation å...
- Page 3 Now you know Part Identifi cation our ABCs. D567 D565 D568 D566 D133 D708 D139 D430 D708 D429 D430 D708 D429 Page 3...
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 40CA CABINET RIGHT - 4 40CB CABINET LEFT - 4 40CC DRAWER RIGHT - 4 40CD DRAWER LEFT - 4 (EXTENSION SET SHOWN SEPARATED) EXTENSION EXTENSION SLIDE...
- Page 5 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. LOCK PACK - 1 189K PULL - 6 GROMMET CAP - 2 HIDDEN WIRELESS Qi COMPATIBLE CORD CLIP - 2 GROMMET - 2 CHARGER by EGGTRONIC - Item 425905 (sold separately) 3S GOLD 5/16"...
- Page 6 Hardware Usage Guide ® HOW TO USE A TWIST-LOCK FASTENER Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 7 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push two SAUDER TWIST-LOCK® FASTENERS (36F) into å the large holes in the MODESTY PANEL (L). Fasten the MODESTY PANEL (L) to the TOP (P).
- Page 8 Step 2 Push four SAUDER TWIST-LOCK® FASTENERS (36F) into å the large holes in the UPRIGHTS (C and D). Do not tighten the TWIST-LOCK® FASTENERS in this step. These holes must be here. Page 8...
- Page 9 Step 3 Separate the EXTENSION SLIDES (40MC) from the EXTENSION RAILS (40MA) as å shown in the upper diagram below. Be prepared, the parts are greasy. Fasten two EXTENSION RAILS (40MA) to the UPRIGHTS (C and D). Use four GOLD å...
- Page 10 Step 4 Fasten two CABINET RIGHTS (40CA) to the LEFT å UPRIGHT (D) and two CABINET LEFTS (40CB) to the RIGHT UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. Fasten the L-LOCK BRACKET (76G) to the LEFT å...
- Page 11 Step 5 Fasten the UPRIGHTS (C and D) to the TOP (P). Tighten four å TWIST-LOCK® FASTENERS. Fasten the UPRIGHTS (C and D) to the MODESTY PANEL (L). å Use four BLACK 2-3/8" FLAT HEAD SCREWS (146S). NOTE: You should start each SCREW a few turns before å...
- Page 12 Step 6 Push eight SAUDER TWIST-LOCK® FASTENERS (36F) å into the large holes in the LOUVERED BACKS (O). Do not tighten the TWIST-LOCK® FASTENERS in this step. (8 used) Page 12...
- Page 13 Step 7 Fasten the LOUVERED BACKS (O) to the UPRIGHTS (C and D). å Tighten four TWIST-LOCK® FASTENERS. i t h ® f a c S u r - L O I S T E R S T E N F A S i t h ®...
- Page 14 Step 8 Push eight HIDDEN CAMS (1F) into the BOTTOMS (E). å Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow (8 used) Metal end Arrow Metal end Page 14...
- Page 15 Step 9 Fasten the BOTTOMS (E) to the UPRIGHTS (C and D). å Tighten four HIDDEN CAMS. Page 15...
- Page 16 Step 10 Push four SAUDER TWIST-LOCK® FASTENERS (36F) into å the large holes in the ENDS (A and B). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 16...
- Page 17 Step 11 Fasten two EXTENSION RAILS (40MA) to the ENDS (A and B). Use å four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. NOTE: For each EXTENSION RAIL, turn a SCREW into the hole å shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to fi...
- Page 18 Step 12 Fasten two CABINET RIGHTS (40CA) to the RIGHT å END (A) and two CABINET LEFTS (40CB) to the LEFT END (B). Use eight GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. Roller end GOLD 5/16" FLAT HEAD SCREW (8 used for the RAILS) Roller end Page 18...
- Page 19 Step 13 Fasten the ENDS (A and B) to the BACKS (O) and TOP (P). å Tighten eight TWIST-LOCK® FASTENERS. Fasten the ENDS (A and B) to the BOTTOMS (E). Tighten å four HIDDEN CAMS. Page 19...
- Page 20 Step 16 Fasten six ANGLE BRACKETS (27G) to the FRONT MOLDING (M). å Use six BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the edges of the ANGLE BRACKETS are even with å the edges of the FRONT MOLDING. BLACK 9/16"...
- Page 21 Step 17 Fasten the FRONT MOLDING (M) to the UPRIGHTS (C and D) å and TOP (P). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS on the FRONT MOLDING and into the holes in the UPRIGHTS and TOP. BLACK 9/16"...
- Page 22 Step 18 Fasten the CORNER BRACKETS (31G) to the BOTTOMS (E). å Use sixteen BLACK 9/16" LARGE HEAD SCREWS (1S). (8 used) BLACK 9/16" LARGE HEAD SCREW (16 used in this step) Page 22...
- Page 23 Step 19 Fasten the SHORT BASES (H) to the CORNER BRACKETS å on the BOTTOMS (E). Use sixteen BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (16 used in this step) Page 23...
- Page 24 Step 20 Fasten eight METAL BRACKETS (4G) to the LONG BASES (G). å Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). (8 used) NOTE: Be sure the BRACKETS are even with the edge of each å LONG BASE. Fasten the LONG BASES (G) to the CORNER BRACKETS on å...
- Page 25 Step 21 Fasten the PENCIL DRAWER BACK (D567) to the PENCIL å DRAWER SIDES (D565 and D566). Use two BLACK 1-9/16" FLAT HEAD SCREWS (30S). Slide the PENCIL DRAWER BOTTOM (B56) into the å grooves in the PENCIL DRAWER SIDES (D565 and D566) and PENCIL DRAWER BACK (D567).
- Page 26 Step 22 Fasten the PENCIL DRAWER FRONT (N) to the PENCIL å DRAWER BOX FRONT (D568). Use two BLACK 7/8" LARGE HEAD SCREWS (17S). Fasten one PULL (189K) to the PENCIL DRAWER FRONT (N). å Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Repeat this step for the other PENCIL DRAWER.
- Page 27 Step 23 Fasten a DRAWER RIGHT (40CC) to the PENCIL RIGHT å DRAWER SIDE (D565) and a DRAWER LEFT (40CD) to the PENCIL LEFT DRAWER SIDE (D566). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. Repeat this step for the other PENCIL DRAWER.
- Page 28 Step 24 The tabs should insert freely With the palm of into the slots. Gently tilt the your hand, tap DRAWER SIDES side to side the DRAWER U n fi until the tabs slip into the slots. BOTTOM down n i s h s u r into the groove.
- Page 29 Step 25 Insert a SLIDE CAM (10A) into the DRAWER SIDES (D133 and D139). å Fasten a DRAWER RIGHT (40CC) to the RIGHT DRAWER SIDE (D133) å and a DRAWER LEFT (40CD) to the LEFT DRAWER SIDE (D139). Use four GOLD 5/16"...
- Page 30 Step 26 The tabs should insert freely With the palm into the slots. Gently tilt the of your hand, DRAWER SIDES side to side tap the until the tabs slip into the DRAWER slots. BOTTOM down into the groove. D708 D430 D430 D429...
- Page 31 Step 27 Insert a SLIDE CAM (10A) into the FILE DRAWER SIDES (D429 and D430). å Fasten the EXTENSION SLIDES (40MC) to the FILE DRAWER SIDES (D429 and D430). å Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
- Page 32 Step 28 Push a FILE GLIDE (6B) onto the FILE RIGHT DRAWER SIDE (D430). å Slide the FILE RODS (8B) into the FILE GLIDE (6B) on the FILE RIGHT å DRAWER SIDE. Slide another FILE GLIDE (6B) onto the other end of the FILE RODS (8B), å...
- Page 33 Step 29 Fasten the LOCK PACK (21J) to the LOCKING DRAWER FRONT (W) å in the exact order shown. NOTE: It is important to position the CAM exactly as shown. å NOTE: Turn the KEY clockwise to lock. å WASHER SCREW The prongs must press into the FILE DRAWER FRONT...
- Page 34 Step 30 Carefully stand your unit upright. å To insert the PENCIL DRAWERS (N) into your unit, tip the front of the drawer down and drop the rollers on the å drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. Repeat this step to insert To insert the DRAWERS (J and W) into your unit, line up the EXTENSION SLIDES on the drawer with the the DRAWERS (K).
- Page 35 Step 32 To make adjustments to the FILE DRAWER loosen SCREW #4 in å the SLIDES a 1/4 turn, then turn the cam clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed.
- Page 36 Step 33 NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. å 35 lbs. each Page 36...