Related Manuals for Teknik Elstree 5426910
Summary of Contents for Teknik Elstree 5426910
- Page 1 Knick-knack paddywhack, give your stuff a home. Hutch with Drawer NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Elstree | Model 5426910 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 5-19 Français 20-22 Español 23-25 Safety Warranty Page 2...
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) BRACE (1) DRAWER BOTTOM (1)
- Page 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. WOOD DOWEL - 4 36F TWIST-LOCK FASTENER - 12 BACK CONNECTOR - 8 ® BRACKET CONNECTOR - 2 189K PULL - 1 180M FELT STRIP - 2 FURNITURE TIPPING METAL PIN - 4 RUBBER SLEEVE - 4...
- Page 5 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 6 Step 2 å Fasten the FIXED SHELF (D) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. N E R S T E ® F A - L O I S T i t h f a c S u r Groove S u r Groove...
- Page 7 Step 3 å To begin assembly, push four SAUDER TWIST-LOCK® FASTENERS (36F) into the Just think. The sooner large holes in the BRACE (F). you do this, the sooner you do something else. Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 7...
- Page 8 Step 4 å Fasten the BRACE (F) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. Page 8...
- Page 9 Step 5 å Push two SAUDER TWIST-LOCK® FASTENERS (36F) into the large holes in the RIGHT END (A). å Insert two WOOD DOWELS (15F) into the RIGHT END (A). å Fasten the RIGHT END (A) to the FIXED SHELF (D) and BRACE (F).
- Page 10 Step 6 å Carefully stand your unit upright. å Slide the BACK (N) into the grooves in the ENDS (A and B) and FIXED SHELF (D). With the palm of your hand, tap the BACK down into the groove. F i n i s h e s u r f a c...
- Page 11 Step 7 å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the TOP. å NOTE: Be sure the groove in the TOP inserts into the BACK.
- Page 12 Step 8 å Fasten eight BACK CONNECTORS (39F) to the ENDS (A and B), TOP (C), BOTTOM (D), Now might be a and BACK (G). Tighten the SCREW in each good time to refresh BACK CONNECTOR. your drink. Use two BACK CONNECTORS per side.
- Page 13 Step 9 å Carefully turn your unit onto its front edges. å Fasten the BRACKET CONNECTORS to the ENDS (A and B). Use four SILVER 1" LARGE HEAD SCREWS (102S). 102S 102S SILVER 1" LARGE HEAD SCREW (4 used in this step) Page 13...
- Page 14 Step 10 å Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (C). Use the short screw provided. å NOTE: Position the SAFETY STRAP exactly as shown. å NOTE: There is no pre-drilled hole in the TOP (C). Use extra force when turning this SCREW.
- Page 15 Step 11 å You have the option to attach this unit to the 426908 and 426909. Below shows how to attach it to either unit. å Fasten the unit to either the 426908 and 426909. Use four SILVER 1" LARGE HEAD SCREWS (102S). 102S SILVER 1"...
- Page 16 Step 12 BLACK 1-9/16" FLAT HEAD SCREW BLACK 1-9/16" FLAT HEAD SCREW (4 used in this step) (4 used in this step) Groove Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. å Slide the DRAWER BOTTOM (L) into the grooves in the å...
- Page 17 Step 13 å Apply the FELT STRIPS (180M) to the bottom, front and back edges of the DRAWER SIDES (J) as shown. å NOTE: The FELT STRIPS should completely cover the bottom edges of the DRAWER SIDES and wrap equally around the front and back edges.
- Page 18 Step 14 å Turn your drawer onto its bottom. If you're doing this to å Fasten the DRAWER FRONT (K) to the DRAWER help a friend, don't BOX FRONT (G). Use four BLACK 7/8" LARGE leave without a bite. HEAD SCREWS (17S). å...
- Page 19 Step 15 å Position your unit in its final location. We recommend using the SAFETY STRAP for added stability. å NOTE: Do not turn the SAFETY DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY STRAP to a wall stud, go to your local hardware store for proper hardware.
- Page 20 Step 16 å Push the RUBBER SLEEVES (2R) over one end of the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELF (E) onto the METAL PINS. å...