Advertisement
Quick Links
Teknik
www.teknikoffice.co.uk
Lateral File
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
Hudson Elm finish | Model 5427871
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 572615
10/18/21
Purchased:
__________________
Advertisement
Related Manuals for Teknik Hudson 5427871
Summary of Contents for Teknik Hudson 5427871
- Page 1 Teknik www.teknikoffice.co.uk Lateral File NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Hudson Elm finish | Model 5427871 PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-28 Français pg 29-32 Español pg 33-36 Lot # 572615 10/18/21 Purchased: __________________...
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 6-28 Hammer Not actual size Français 29-32 Español 33-36 Safety 37-38 Warranty Page 2...
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) D576 RIGHT DRAWER SIDE (2) LOWER DRAWER FRONT (1)
- Page 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) EXTENSION EXTENSION 10A SLIDE CAM - 4 33A FILE ROD - 4 35MA 35MC RAIL - 4 SLIDE - 4 FILE 4B FILE GLIDE - 4 14B FILE BAR - 4...
- Page 5 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 3S GOLD 5/16" FLAT HEAD SCREW - 18 BLACK 9/16" LARGE HEAD SCREW - 4 6S BROWN 7/16" LARGE HEAD SCREW - 8 11S BLACK 1/2" FLAT HEAD SCREW - 6 30S BLACK 1-9/16"...
- Page 6 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper diagram below. Be prepared, the parts are greasy.
- Page 7 Step 2 å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT END (A). Use three BLACK 9/16" PAN HEAD SCREWS (51S). å Fasten the L-LOCK BRACKET (76G) to the RIGHT END (A) exactly as shown. Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
- Page 8 Step 3 å Using your hammer, gently tap two LEVELERS (46E) completely into the holes in the RIGHT END (A). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. å Insert two WOOD DOWELS (42F) into the RIGHT END (A). å...
- Page 9 Step 4 å Insert eight WOOD DOWELS (42F) into the BACKS (G). Just think. The sooner å NOTE: You may need to gently tap the WOOD DOWEL in you do this, the sooner with your hammer. you do something else. (8 used) Page 9...
- Page 10 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER into the large hole in the part. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 11 Step 5 å Fasten the BACKS (G) to the RIGHT END (A). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the BACKS insert into the RIGHT END. i t h ® f a c S u r - L O I S T E R S...
- Page 12 Step 6 å Insert four WOOD DOWELS (42F) into the BOTTOM (D). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. Page 12...
- Page 13 Step 7 å Fasten the BOTTOM (D) to the RIGHT END (A). Tighten two TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the BOTTOM insert into the RIGHT END. S u r f a c i t h I S T - L O F A S...
- Page 14 Step 8 å Fasten the remaining two EXTENSION RAILS (35MA) to the LEFT END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram.
- Page 15 Step 9 å Using your hammer, gently tap the remaining two LEVELERS (46E) completely into the holes in the LEFT END (B). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. å...
- Page 16 Step 10 å Fasten the LEFT END (B) to the BOTTOM (D) and BACKS (G). Tighten six TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the BOTTOM and BACKS insert into the LEFT END. Page 16...
- Page 17 Step 11 å Fasten the BASE (E) to the ENDS (A and B) and BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS. Now might be a good time to refresh your drink. Page 17...
- Page 18 Step 12 å Carefully stand your unit upright. å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the TOP. Page 18...
- Page 19 Step 13 å Fasten the Z - LOCK BRACKET (77G) to the UPPER DRAWER FRONT (J). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (2 used in this step) Page 19...
- Page 20 Step 14 The tabs should insert freely With the palm of your hand, into the slots. Gently tilt the tap the DRAWER BOTTOM DRAWER SIDES side to side down into the groove. D576 until the tabs slip into the slots. U n fi n i s h s u r...
- Page 21 Step 15 å Fasten two FILE BRACKETS (12B) to the UPPER DRAWER FRONT (J) and DRAWER BACK (D578). Use four BROWN 7/16" LARGE HEAD SCREWS (6S). BROWN 7/16" LARGE HEAD SCREW (4 used in this step) D578 Page 21...
- Page 22 Step 16 å Insert a SLIDE CAM (10A) into each DRAWER SIDE (D576 and D577). å Fasten the EXTENSION SLIDES (35MC) to the DRAWER SIDES (D576 and D577). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å...
- Page 23 Step 17 å Fasten one PULL (202K) to the UPPER DRAWER FRONT (J). Use two BLACK 7/8" MACHINE SCREWS (37S). å Repeat steps 14-17 for the remaining drawer using the LOWER DRAWER FRONT (H). BLACK 7/8" MACHINE SCREW (2 used in this step) 202K Page 23...
- Page 24 Step 18 å Fasten a DRAWER ACTUATOR (62G) to each RIGHT DRAWER SIDE (D576) exactly as shown. Use six BLACK Almost time to 1/2" FLAT HEAD SCREWS (11S). celebrate! With a nap. å NOTE: Be sure to use the lower set of holes in the UPPER DRAWER (J) and the upper set of holes in the LOWER DRAWER (H) as shown in the diagram.
- Page 25 Step 19 å NOTE: The drawers will accommodate letter or legal size hanging files. å Press a FILE GLIDE (4B) onto the top edge of the RIGHT DRAWER SIDE (D576). å Slide the FILE RODS (33A) through a FILE BAR (14B), through the holes in the FILE BRACKETS (12B), through another FILE BAR (14B), and into the FILE GLIDE (4B) on the RIGHT DRAWER SIDE (D576).
- Page 26 Step 20 å Fasten the LOCK PACK (21J) to the LOWER DRAWER FRONT (H) in the exact order shown. å NOTE: It is important to position the CAM exactly as shown. å NOTE: Turn the KEY clockwise to lock. WASHER SCREW The prongs must press into the FILE DRAWER FRONT...
- Page 27 Step 21 å Pull the lower wing of the INTERLOCK MECHANISM (34G) forward until it clicks into place as shown in Diagram 1. å To insert the lower drawer into your unit, line up the EXTENSION SLIDES on the drawers with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer it is fully inserted.
- Page 28 Step 22 å To make adjustments to the drawer, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the cam clockwise or counter- clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed.