Table of Contents
Advertisement
Quick Links
Smart Pro™ Dust Collector - XXS200001
Owner's Manual
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, NY 13204
Phone 1.800.732.4065 315.476.5151 Fax 315.476.5044 www.oneida-air.com
Pat. # 8,491,685
Filter Flame Guard
Arrestor - U.S.
Pat. # 8,496,719
Winner of...
for Product Innovation in
Machinery Under $50,000
Shown with optional
Stand and Drum.
Models may vary slightly
in appearance.
ZBM000104
9_11
Advertisement
Table of Contents
Related Manuals for Oneida Air Systems Smart Pro XXS200001
Summary of Contents for Oneida Air Systems Smart Pro XXS200001
- Page 1 Machinery Under $50,000 Shown with optional Filter Flame Guard Stand and Drum. Arrestor - U.S. Pat. # 8,496,719 Models may vary slightly in appearance. Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, NY 13204 Phone 1.800.732.4065 315.476.5151 Fax 315.476.5044 www.oneida-air.com...
-
Page 2: Table Of Contents
Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 8:30am - 5:00pm EST Mon. - Fri. to answer any questions concerning OAS products and dust collection. Call for duct- work design and ductwork quotes, including system pricing and shipping cost. -
Page 3: System Start-Up Information
I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual 2. Install ductwork completely before operating collector: A.) Seal ductwork with silicone sealant or duct tape. B.) Have dust bin in place and sealed. 3. -
Page 4: Features
II. Features External Cartridge Filter - Silencer Included with Filter Cartridge Filter Media GE Certified (H-12) HEPA Media. MERV 16+ rated. Pat. Pend. Flame Guard Arrestor Filter Grounding Wire Included Dust Sentry™ Optional Wall Bracket Included Silencer Included Remote Starter Do Not Remove Pat. -
Page 5: General Specifications & Fan Performance Curve
III. General Specifications & Fan Performance Curves XXS200001 System 1625 Max. CFM Performance Height w/ 35 Gallon Drum: 94” Footprint w/ Ext. Cartridge: 36” x 48” System Inlet Diameter: Welded 7” w/ Neutral Vane Dimensions Powder Coated Paint Finish Over Heavy Gauge Steel Seam-Welded Cyclone 35 Gal. -
Page 6: System Contents
IV. System Contents *Not to Size FPZ000018 BHX001800 BHX001803 BXI050118 SXI002108 SCX002109 FCS183600HF Optional 35 & 55 Gal. Drum Kits - OEK550901 / OEK350901 FPX010018 BCS180000 SEX550900 ACB120000 DHF090000 FPX000001 SES350000 SES550000 Optional Wall Bracket - SMS300021 System Hardware Kit - AHX001800 Plenum Hardware Smart Pro™... -
Page 7: Dimensions
V. Dimensions For Minimum Mounting Heights w/ 36” Filter & 35 / 55 Gal. Drums *Dimensions subject to slight variation in manufacturing. 75.5 / 87.5” 7” Dia. 94” - 35 Gal. 103” - 55 Gal. 36” 18” 66.5”/ 78.5” 56”/ 68”... -
Page 8: Wall Bracket Assembly Instructions
VI. Bracket Assembly 26 1/4” Slots in the brackets are .406” x 1.00”. 24” Note: Bolts included to mount bracket to collector. Hardware NOT included to mount to wall. 1. Hold bracket against wall with top of plate at 56” for 35 gal. drum or 69”... -
Page 9: General Assembly Instructions
VI. General Assembly Instructions Do NOT use hook on motor to lift unit. With all assemblies, make sure rectangular air outlet is oriented on Fan/Blower housing as you are looking down as in Fig. 1A or facing it as shown in diagrams. This is very important. Before you start, make sure you have cut and placed the provided gasket material on top and bottom of the Fan / Blower housing and the Cone as shown in the diagrams. - Page 10 VI. General Assembly Instructions (Cont.) 6. Attach (2) U-Spring clips (AFT010916) to either side of the motor with the flat side of the clip facing out. Motor cowling will not fit otherwise. Put cowling (BHX001803) over the motor and attach with (2) sheet metal screws (AFS010075) on each side by screwing into spring clips.
-
Page 11: Drum Assembly
VII. Drum Assembly Drum Grounding Wire Distance between the drum lid and cone can vary. Some systems have little space there to To attach the Drum Grounding Wire, start a minimize overall system height. small hole in bottom of In some cases, the flexible hose will have to be cone above flex hose and in the top of the cut down (especially with stands). -
Page 12: Start And Infrared Level Drum Sensor Assembly
IX. Starter Assembly Plug in Starter You can attach your Control Box to a wall by screws, or to your collector by double sided velcro or magnets or you can just set it on the dust bin top. You must let your dust collector completely stop before you restart your collector. If you can’t restart your collector, see the Troubleshooting section of the manual. -
Page 13: Stand Assembly
X. Stand Assembly 35 & 55 Gal. Stand - STG000035 / STG000055 Top Gusset Stand Kit Contents Stand Brace Hardware Kit (1) - AHX000100 Mid - Gusset 56” / 68” Rubber Leg Cap (4) - RCR012500 Top Gusset (4) - RFG010000 Rubber Leg Cap 27.5”... -
Page 14: Filter Maintenance
Filter Grounding Wire Figure 1 Attach the ring terminal on the green ground wire from the motor to a bolt on the filter plate, under the nut. Then attach the alligator clip to the filter cage as shown in Fig. 1. XI. -
Page 15: Directions For Cleaning Filter
XII. Directions for Cleaning the Filter All steps should be done with a dust mask and eye protection. Proper filter clean- ing should not be neglected. A dirty filter can affect dust collector operation and filter life. 1. Compressed air from outside. Blast air along pleats of the filter at about a 20 degree angle. -
Page 16: Fan Motor Maintenance
XIII. Fan Motor Maintenance Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated every 5500 hours. Smart Pro™ © O.A.S. 2011... -
Page 17: Accessories
XIV. Accessories Bolt Together Stand STG000035 - 35 Gal. Stand STG000055 - 55 Gal. Stand Replacement Filter w/ Pat. Pend. Flame Guard Arrestor FCS183600HF 18”x 36” / 110 Sq. Ft. GE HEPA (H-12) Filter Media. Dust Containers 55 Gal. Steel The BAG Gripper ABX000000 The BAG Gripper provides the ability to use convenient plastic bags inside... -
Page 18: Troubleshooting
Note: If you continue to experience difficulty Motor Overheating with your collector, call Oneida Air Systems at The motor’s internal circuit breaker will trip if the motor is overheating. 1.800.732.4065 for assis- Motor amperage too high - Shut system down. -
Page 19: Fire Hazards - Read Before Installing System
XVI. Fire Hazards - Read Before Installing and Operating Oneida Collectors are designed for WOOD DUST only!! Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding flame front which can cause an explo- sion if tightly contained. -
Page 20: Terms & Conditions
Returned Goods Policy Buyer must inform Oneida Air Systems of any shortage or damage, by so noting in writing, on the freight delivery bill prior to signing to indicate receipt of shipment. All claims covered under the limited warranty, are subject to inspection and investigation by Oneida Air Systems. Oneida Air Systems reserves the right to inspect and investigate all returned products before Buyer’s claim is settled.