Related Manuals for Oneida Air Systems Mini-Gorilla
Summary of Contents for Oneida Air Systems Mini-Gorilla
- Page 1 OWNER’S MANUAL Mini-Gorilla 110V / 220V # XXPM010100H # XXPM010100H220 U.S. Patent: # #7824457, #8377160, #8491686, #8496719, #7937803 Appearance may vary slightly Rev: 12/20/2018 Doc. #ZBM000024A...
-
Page 3: Table Of Contents
Table of Contents System Start-Up Information System Specifications System Dimensions System Contents Assembly Instructions Maintenance Troubleshooting Recommended Accessories Warranty Information Notes oneida-air.com... -
Page 4: System Start-Up Information
5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or failure to follow these directions). - Page 5 System Start-Up Information (Continued) d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. ft. or to areas where dust producing equipment requires an aggregate dust collection flow rate of more than 1,500 cfm (cubic feet per minute).
-
Page 6: System Specifications
99.97% @ 0.3 microns Filter Surface Area 40 Sq. Ft. (3.7 sq m) SYSTEM DIMENSIONS AND CONSTRUC TION Barrel/Cyclone Body Heavy-gauge cold-rolled steel Inlet 5" (127 mm) Outer Diameter Overall Height 64" (1,626 mm) Overall Weight 85 lbs (38.5 kg) Oneida Air Systems... -
Page 7: System Dimensions
System Dimensions Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. The Mini-Gorilla requires a 20 Amp outlet receptacle Top View 28" to be installed by a licensed electrician. See below outlet 711 mm receptacles needed based on the voltage of your unit. -
Page 8: System Contents
You will need the following: • 7/16" Wrench • 1/2" Socket Wrench • Flat-head Screwdriver • 7/16" Socket Wrench • Ball-Peen Hammer • Razor Blade • 1/2" Wrench • Phillips Head Screwdriver Oneida Air Systems... - Page 9 System Contents (Continued) oneida-air.com...
-
Page 10: Assembly Instructions
5/16" x 2" Hex Head Bolts (C9K). [FIG. 2a] Secure Stem Casters (C9G) to the threaded insert on the bottom of the legs. Finger tighten. [FIG. 2b] FIG. 2b SECTION G-G SECTION G-G DETAIL I SCALE 1 : 1 Oneida Air Systems... - Page 11 Assembly Instructions (Continued) Install Straight Fittings (C9D) into the recessed FIG. 3a hole under the fan housing and near the bottom of the drum. [FIG. 3a] Secure in place using the fitting’s nut on the inside; using a Rubber Washer (C9E) between the nut and the inner wall.
- Page 12 [FIG. 6a] Note: If you do not want to use bags you MUST FIG. 6a use the Cap (C9F) to close off the fitting. [FIG. 6b] FIG. 6b 10 Oneida Air Systems...
- Page 13 Assembly Instructions (Continued) Latch the Drum to the cone assembly and connect the Vinyl Tubing (C9B) onto both Straight Fittings (C9D). Push tubing on until all barbs are covered. [FIG. 7] FIG. 7 Tap the U-Spring Nuts (C9R) onto each of the holes around the circle of the Fan Housing with a ball peen hammer.
- Page 14 5/16" Flat Washers (C9T). Motor Plate Note: If U-Spring Nuts (C9R) don't align with Fan Housing the motor plate holes, use a screwdriver to adjust misalignment. Hand tighten first and then tighten down. Motor Plate FIG. 10 12 Oneida Air Systems...
- Page 15 Assembly Instructions (Continued) Lift the Filter (B) up to the plenum elbow, FIG. 11a slotting the filter’s bolts into the four grooves. shown in [FIG. 11a]. Secure in place with four 5/16" Flat Washers (C9W) and four Nylock Nuts (C9X). [FIG. 11b] Note: DO NOT overtighten.
-
Page 16: Maintenance
6” away from the filter; closer blasts may damage the filter material. Direct air out and away from anyone in the area. Do not use this method when any hazardous material has been vacuumed up. 20º 14 Oneida Air Systems... -
Page 17: Troubleshooting
Clean filter more often with compressed air. If you continue to experience difficulty with your dust collector, call Oneida Air Systems’ Customer Service Department at 1-866-387-8822 or email support@oneida-air.com. oneida-air.com... -
Page 18: Recommended Accessories
• Detects when your power tools are on and automatically turns on the dust collector for you! • Includes 1 Remote Control with belt-clip. • Switch receives signals from up to 40' away in any direction. 16 Oneida Air Systems... - Page 19 Recommended Accessories (Continued) iVAC Pro Tool Plus Automatic Power Sensor #STZ212301 • Up to 8 tool sensors can be synced to the same switch. • Transmits radio frequency signal to the iVAC Pro Switch from up to 40' away. • Multiple operating modes for automatic or direct manual control of the system. 5"...
-
Page 20: Warranty Information
In no event shall Oneida Air Systems’ liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Oneida Air Systems shall be tried in the State of New York, County of Onondaga. -
Page 21: Notes
Notes oneida-air.com... - Page 22 Regardless of where you purchased your system, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems first to let us help resolve your problem. We fully stand behind the quality of our product and place the utmost value on our customer’s opinion.