Table of Contents
Advertisement
F: Key Sync.................................................. [ON, OFF]
Specify whether the arpeggiator will be synchronized to the
keyboard.
If this is ON, the arpeggiator will always start from the
beginning of the arpeggio pattern when you play the key-
board. If you are performing together with other instru-
ments, you can use this function to ensure that the arpeggio
pattern is aligned with the beginning of the measure.
G: Resolution ............................................ [1/24...1/4]
Specify the resolution (spacing of the notes) relative to the
tempo specified by "Tempo." ( P.66 "How "Resolution"
and "Sync Note" values correspond to note values")
With a setting of 1/4, the arpeggio will be played as quarter
notes of the specified tempo.
With a setting of 1/6, the arpeggio will be played as quarter
note triplets of the specified tempo.
With a setting of 1/8, the arpeggio will be played as eighth
notes of the specified tempo.
With a setting of 1/12, the arpeggio will be played as eighth
note triplets of the specified tempo.
With a setting of 1/16, the arpeggio will be played as six-
teenth notes of the specified tempo.
With a setting of 1/24, the arpeggio will be played as six-
teenth note triplets of the specified tempo.
H: Swing ...........................................[–100%...+100%]
This skews the timing of the even-numbered notes (counting
from the first note) of the arpeggio.
When Resolution = 1/8
1
2
3
Swing
–50
–25
UTILITY
Here you can use various utility functions such as copy, ini-
tialize, and swap (exchange) to help you edit more effi-
ciently.
Page26: UTILITY
A: InitProgram
This function initializes the settings of the currently selected
program (timbre, effect, arpeggiator).
When you initialize a program, its voice mode will be Sin-
gle.
Procedure
1 In LCD Edit mode, press the SELECT [16] key.
The LCD screen will show Page 26A: UTILITY "InitPro-
gram."
26A UTILITY
InitProgram
2 Press the [+/YES] key.
46
4
5
6
7
8
+25
+50
OK?
You will be asked to confirm the initialize operation.
3 Press the [+/YES] key once again.
The program will be initialized, and the display will
indicate "Completed."
4 Press the [EXIT] key.
You will return to the first screen of the "InitProgram"
function.
B: InitTimbre
This function initializes the settings of the currently selected
timbre.
Procedure
1 In LCD Edit mode, press the SELECT [16] key, and
then press the CURSOR [®] key once.
The LCD screen will show Page 26B: UTILITY "InitTim-
bre."
2 Press the [+/YES] key.
You will be asked to confirm the initialize operation.
3 Press the [+/YES] key once again.
9
The timbre will be initialized, and the display will indi-
cate "Completed."
4 Press the [EXIT] key.
You will return to the first screen of the "InitTimbre"
function.
C: CopyTimbre
This function copies the setting of another timbre to the cur-
rently selected timbre.
Source Program ........................................ [A01...H16]
Select the copy source program.
Source Timbre ..................................................... [1, 2]
Select the copy source timbre.
Procedure
1 In LCD Edit mode, press the SELECT [16] key, and
then press the CURSOR [®] key twice.
The LCD screen will show Page 26C: UTILITY "Copy-
Timbre."
2 Press the [+/YES] key.
The LCD screen will show the copy source program
(Source Program) and timbre (Source Timbre).
Source Program
26A UTILITY
Are You Sure OK?
26B UTILITY
InitTimbre
OK?
26B UTILITY
Are You Sure OK?
26C UTILITY
CopyTimbre
OK?
26C UTILITY
A01 T:1
OK?
Source Timbre
Advertisement
Table of Contents
