Mixer; Page07: Mixer; Filter; Page08: Filter - Korg MS2000R Owner's Manual

Korg owner's manual analog modeling synthesizer ms2000, ms2000r
Hide thumbs Also See for MS2000R:
Table of Contents

Advertisement

MIXER

Page07: MIXER

This sets the output level of the carrier. The level you specify
here will be the input level to the band-pass filter of the car-
rier.
A: OSC 1 Level
Specify the output level of OSC1 (carrier).
B: Inst Level
Specify the output level of the signal that is input from the
AUDIO IN 1 jack.
C: Noise Level
Specify the output level of the noise generator.

FILTER

These are the parameters for the band-pass filter of the car-
rier.

Page08: FILTER

A: Formant Shift
This shifts the cutoff frequency of each band-pass filter of the
carrier, allowing you to dramatically modify the character of
the vocoder output.
B: Cutoff
This continuously shifts the cutoff frequency of each band-
pass filter of the carrier.
How "Formant Shift" and "Cutoff" are related
When "Formant Shift" = 0 and "Cutoff" = 0, the frequency
response will be as specified by the cutoff frequencies of
each band-pass filter of the modulator.
Adjustments to "Cutoff" will smoothly shift the frequency
response
The shift in frequency response caused by "Formant Shift"
is smoothly varied by "Cutoff" in two stages above and
two stages below (four stages above and below when used
in conjunction with "Formant Shift").
BPF
BPF
BPF
BPF
7
-63
Cutoff (range in which BPF 8 will change)
Formant Shift:+2
-63
C: Resonance
Specify the amount of resonance for each band-pass filter.
Increasing this value will emphasize the regions near each
cutoff frequency.
50
..........................[000...127]
.................................[000...127]
...........................[000...127]
................... [–2...+2]
................................. [–63...+63]
BPF
BPF
8
9
Frequency
0
+63
BPF
BPF
BPF
BPF
BPF
BPF
7
8
9
Frequency
+63
0
Cutoff (range in which BPF 8 will change)
....................[000...127]
D: Mod Src
Select the modulation source that will be applied to "Cut-
off."
The selectable modulation sources are the same as for the
Virtual Patch modulation sources (Source) for synth parame-
ters.
Refer to p.42 " VIRTUAL PATCH."
E: Mod Int
Specify the depth of the modulation that will be applied to
"Cutoff."
F: E.F.Sense
Specify the sensitivity of the envelope follower of the modu-
lator.
With low settings of this parameter, the rise and fall of the
signal from the AUDIO IN 2 jack will be detected rapidly.
With high settings of this parameter, the change will become
slower, producing a sound with no attack and a long release.
With a setting of 127, the response of the signal being input
at that time will be maintained. Subsequently, the sound will
be produced with the response that is being held, regardless
of whether or not there is any input.
If you set this to 127 when there is no input signal
present there will be no output even if an audio signal
is subsequently input.
AMP

Page09: AMP

A: Level
.................................... [000...127]
Specify the volume level of the internal tone generator
(OSC1/NOISE) for the carrier.
B: Direct Level
Specify the volume level of the audio that is output directly
from the AUDIO IN 2 jack.
C: Distortion
If this is ON, distortion will be applied to the OSC1/NOISE/
AUDIO IN 1 signal.
D: Vel Sense ............................................... [–63...+63]
Specify how velocity (keyboard playing dynamics) will
affect the volume.
With positive (+) settings, the volume will increase as you
play harder.
With negative (–) settings, the volume will decrease as you
play harder.
E: KBD Track............................................... [–63...+63]
Specify how keyboard tracking will affect the volume.
With positive (+) settings, the volume will increase as you
play above the C4 note on the keyboard, and will decrease as
you play below C4.
With negative (–) settings, the volume will decrease as you
play above the C4 note on the keyboard, and will increase as
you play below C4.
................. [EG 1...MIDI 2]
......................... [–63...+63]
......................... [000...127]
................. [000...127]
........................[ON, OFF]

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ms2000

Table of Contents