Arpeggiator; System Exclusive Messages - Korg MS2000R Owner's Manual

Korg owner's manual analog modeling synthesizer ms2000, ms2000r
Hide thumbs Also See for MS2000R:
Table of Contents

Advertisement

*1:
• When "Knob" = Step Length, data correspondences for
both transmission and reception will be:
0...9: –6, 10...19: –5, 20..29: –4, 30...39: –3, 40...49: –2,
50...59: –1, 60...68: 0, 69...78: +1, 79...88: +2, 89...98: +3,
99...108: +4, 109...118: +5, 119...127: +6
• When "Knob" = Pitch or OSC2 Semi, refer to p.66 "OSC
2 Semitone values."
• When "Knob=" other values, both transmission and
reception will be:
0/1: –63, 2: –62...64: 0...127: +63
If you are using two MS2000/MS2000R units to trans-
mit and receive these parameters, you must set the
transmitting and receiving programs to the same set-
tings.
Sync control
The first-played note-on will sync a Mod Sequence or LFO
whose "KeySync" = Timbre. However in order to distin-
guish manually played note-on/off's from those that are
repeated automatically by the arpeggiator, the MS2000/
MS2000R's arpeggiator will transmit a Sync Control mes-
sage at the time of note-on (when Global mode Page 1C:
GLOBAL "Position" is PostKBD).
A control change message is used for this Sync Control
message as specified by Global mode Page 4G: MIDI FIL-
TER "SyncCtrl."
By using Sync Control to apply sync to a Mod Sequence or
LFO, you can cause each arpeggiated note to advance the
Mod Sequence or random LFO by one step.
Silencing all notes of a given channel
• All note off (CC#123) [Bn, 7B, 00]
(value is 00)
When an All Note Off message is received, all currently-
sounding notes of that channel will be turned off. Some
sound may linger due to the envelope settings.
• All sound off (CC#120) [Bn, 78, 00]
(value is 00)
When an All Sound Off message is received, all notes cur-
rently sounding on that channel will be silenced. While All
Note Off allows the decay of a note to continue, the All
Sound Off will silence the sound immediately.
However, this message is intended for use in emergencies,
and is not for use during a performance.
Resetting all controllers of a given channel
• Reset all controllers (CC#121) [Bn, 79, 00]
(value is 00)
When a Reset All Controllers message is received, all con-
troller values currently operating on that channel will be
reset.

Arpeggiator

When the MS2000/MS2000R's arpeggiator is synchronized
to a connected external MIDI device, system realtime mes-
sages Start and Stop will control the arpeggiator.
Start [FA]
When a Start [FA] message is received, the arpeggiator will
start from the pitch of the first played note.
Stop [FC]
When a Stop [FC] message is received, the arpeggiator will
stop. (It will not be turned off; the arpeggiator will start
again when additional notes are played.)

System exclusive messages

MS2000/MS2000R format
F0: exclusive status
42: Korg ID
3n: [n=0–F] global MIDI channel
58: MS2000/MS2000R model ID
ff: function ID (type of message)
F7: end of exclusive
Universal system exclusive
System exclusive messages include a special category of
messages whose purpose is officially defined. These are
called universal system exclusive messages.
Of these universal system exclusive messages, the MS2000/
MS2000R supports Master Volume and Master Fine Tun-
ing.
Master volume [F0, 7F, nn, 04, 01, vv, mm, F7]
(vv: lower byte of value, mm: upper byte of value, [mm,
vv=7F, 7F] is Max, [mm, vv=00, 00] is 0)
When a Master Volume message is received, the MS2000/
MS2000R will adjust its overall volume.
If Global mode Page 1E: GLOBAL "AudioInThru" is
ON, the input signal of AUDIO IN 1/2 will not be
affected by Master Volume.
Master fine tuning [F0, 7F, nn, 04, 03, vv, mm, F7]
(A value of 8192 [mm, vv=40, 00] is center (0 cent,
A4=440.0Hz), 4096 [mm, vv=20, 00] is –50 cents, and 12288
[mm, vv=60, 00] is +50 cents.)
When master fine tuning is received, the value specified for
the MS2000/MS2000R's Global mode Page 1A: GLOBAL
"Mst.Tune" will be ignored, and the overall pitch will be
specified by the data that was received.
Appendices
63

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ms2000

Table of Contents