Page4: Midi Filter - Korg MS2000R Owner's Manual

Korg owner's manual analog modeling synthesizer ms2000, ms2000r
Hide thumbs Also See for MS2000R:
Table of Contents

Advertisement

E: MIDI2 .............................................[P.Bend...CC#95]
Select the function that will be assigned to modulation
source MIDI 2 of the virtual patch. (With the factory settings,
this is CC#01.)
If the specified setting is assigned to another parameter,
an "*" will be shown in the right of the upper line of the
LCD screen.
F: MIDI Dump......................................... [1PROG...ALL]
Select the data that you wish to dump.
This function transmits the MS2000/MS2000R's programs
and global settings to a MIDI data filer or computer con-
nected to the MIDI OUT connector. The same data can also
be transmitted to another MS2000/MS2000R.
For the dump procedure, refer to p.31 Basic Guide, Edit sec-
tion "4. Saving data on an external device (Data Dump)."
To receive this data, set Global mode Page 4D: MIDI FILTER
"SystemEx" to ENA, and you will be able to receive a data
dump at any time.
Data is transmitted and received on the global MIDI channel.
1PROG
Data for the currently selected program will be transmit-
ted.
PROG
Data for all programs will be transmitted.
GLOBAL
Global data will be transmitted.
ALL
All programs and global data will be transmitted.
The following times are required in order to perform the
various types of data dump.
Data to dump
Data size (Bytes)
1PROG
291
PROG
37,157
GLOBAL
227
ALL
37,383

Page4: MIDI FILTER

A: ProgChg.................................................. [DIS, ENA]
Select whether or not program changes will be transmitted
and received.
ENA
Program changes will be transmitted and received.
DIS
Program changes will not be transmitted or received.
B: CtrlChg .................................................... [DIS, ENA]
Select whether or not MIDI control changes will be transmit-
ted and received.
ENA
MIDI control changes will be transmitted and received.
DIS
MIDI control changes will not be transmitted or received.
C: P.Bend ..................................................... [DIS, ENA]
Select whether or not pitch bend messages will be transmit-
ted and received.
ENA
Pitch bend messages will be transmitted and received.
DIS
Pitch bend messages will not be transmitted or received.
D: SystemEx ................................................ [DIS, ENA]
Select whether or not MIDI system exclusive messages will
be transmitted and received.
ENA
MIDI system exclusive messages will be transmitted and
received.
DIS
MIDI system exclusive messages will not be transmitted or
received.
E: NoteRcv..................................................[ALL...ODD]
When note data is received, specify the note numbers (even
numbered notes, odd numbered notes, all notes) that will be
sounded by the MS2000/MS2000R.
ALL
All note numbers will be received. Normally you will
leave this set at ALL. If you have connected an MS2000 or
an addition MS2000R to an MS2000R to increase the
polyphony, set one unit to EVN and the other to ODD so
that either one or the other will sound.
Time required (seconds)
Less than one second
approximately 15
Less than one second
approximately 15
EVN
Even-numbered notes (C, D, E, F#, G#, A#) will be
sounded.
ODD
Odd-numbered notes (C#, D#, F, G, A, B) will be sounded.
F: P.Chg
Here you can freely specify the correspondence between the
MS2000/MS2000R's program numbers and the incoming
MIDI program change numbers.
External ..................................................... [000...127]
Select the incoming MIDI program change number.
Internal ..................................................... [A00...H16]
Select the MS2000/MS2000R program number.
EVN or ODD are valid only if the program has an
"Assign" setting (LCD Edit mode Page 03A: VOICE) of
Poly.
MS2000
MIDI OUT
ODD
MIDI OUT
MIDI IN
MIDI THRU
MS2000R#1
MIDI keyboard, etc.
EVN
There is no effect on the MIDI data that is received.
4F MIDI FILTER
P.Chg[000]:A01
External
Parameter Guide
MIDI IN
MS2000R
EVN
MIDI IN
MS2000R#2
ODD
Internal
55

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ms2000

Table of Contents