Lfo (Low Frequency Oscillator); Page12: Lfo 1; Page13: Lfo 2 - Korg MS2000R Owner's Manual

E: EG Reset .................................................. [ON, OFF]
Specify whether or not the EG will be reset for the second
and subsequent note-on.
If this is ON, the second note-on will start from a level of 0.
If this is OFF, the note will start from the current EG level.
Note on Note off
ON
OFF
"EG Reset" is valid in the following cases.
•When Page 03A: VOICE "Assign" is Poly.
•When Page 03A: VOICE "Assign" is Mono or Unison
and Page 03D: VOICE "Trigger" is Multi.

LFO (Low Frequency Oscillator)

These are the LFO (Low Frequency Oscillator) parameters
used to create cyclic change.
LFO1 is internally connected as the modulation source for
Page 05B: OSC1 "Control 1."
LFO2 is internally connected as the modulation source for
oscillator pitch via the modulation wheel (on the MS2000R,
the modulation wheel of a connected external MIDI device).
If you have difficulty hearing the effect of the LFO,
increase the depth or intensity values of the modula-
tion destination.

Page12: LFO 1

Page13: LFO 2

A: Wave SELECT ................................... [Saw...S/H]
Select the LFO waveform.
For LFO1 you can select from Saw, Squ, Tri, and S/H.
For LFO2 you can select from Saw, Squ (+), Sin, and S/H.
Saw
Squ (+)
Sin
Note on (Retrigger)
Squ
Tri
S/H
Amplitude changes irregularly
(sample & hold)
B: Key Sync ................................... [OFF, Timbre, Voice]
Specify how the LFO will be applied to a voice when note-on
occurs.
OFF
The LFO phase will not be reset when note-on occurs.
Note on
Timbre
The LFO phase will be reset at the first note-on that occurs
from a state of no keys pressed. Subsequently, modulation
will continue to be applied at the same LFO phase even for
subsequent note-on's.
Note on
Note all off
Voice
The LFO phase will be reset at each note-on, and modula-
tion of differing phases will apply to each voice.
Note on
1VOICE
2VOICE
C: Tempo Sync ..............................................[ON, OFF]
If this is ON, the LFO frequency will synchronize to the
tempo or to MIDI clock.
If the Global mode Page 3C: MIDI "Clock" setting is Inter-
nal, the LFO will synchronize to the tempo specified by the
[TEMPO] knob. If the setting is External, the LFO will syn-
chronize to the MIDI clock received from an external MIDI
device.
If "Tempo Sync" is ON, setting Page 14A–17A:
PATCH1–4 "Destination" to LFO2Freq will have no
effect.
D: Frequency FREQUENCY ..................... [000...127]
Specify the frequency of the LFO. Increasing this value will
result in a faster frequency.
This parameter will be displayed and can be set if "Tempo
Sync" is OFF.
If "Tempo Sync" is ON, this will indicate "Sync Note."
E: Sync Note............................................. [1/32...1/1]
Specify the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. ( P.66 "How "Resolution" and "Sync
Note" values correspond to note values")
This parameter will be displayed and can be set if "Tempo
Sync" is ON.
At a setting of 1/1, there will be one cycle every four beats.
At a setting of 1/2, there will be two cycles every four beats.
At a setting of 1/4, there will be one cycle every beat.
At a setting of 1/8, there will be two cycles every beat.
Parameter Guide
Note on
Note on
41