Page 1
Source 4WRD PAR and PARNel Fixture Bodies Installation and User Manual Part Number: 7067M1220 Rev E Released: 2021-04...
Page 2
To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. ETC intends this document, whether printed or electronic, to be provided in its entirety.
Set the Angle within the Yoke Use the Accessory Holder Loosen the Z-adjustment Knob Adjust the Focus Knob (PARNel Fixtures Only) About PAR Lenses Clean and Maintain the Fixture Clean the Fixture Store the Retrofit Clean the Lenses Change a PAR Lens Source 4WRD Installation and User Manual...
Page 4
Change a Front PARNel Lens Clean the Reflector Source 4WRD Installation and User Manual...
Introduction Use the Source 4WRD LED, Source 4WRD II LED, or Source 4WRD Color retrofit (supplied separately) with the Source 4WRD PAR or PARNel Fixture Body to create the Source 4WRD PAR or PARNel fixture. For best results, we recommend that you use the included diffusion on the Source 4WRD PAR or PARNel Fixture Body when paired with the Source 4WRD Color.
ETC support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none of these resources are sufficient, contact ETC Technical Services directly at one of the offices identified below. Emergency service is available from all ETC offices outside of normal business hours.
Safety The Source 4WRD fixture is intended for professional use only. Read the entire manual before using this equipment. WARNING: This fixture must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
Page 8
WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Installing the Source 4WRD LED retrofit kit requires knowledge of luminaire electrical systems. If you are not qualified, do not attempt installation. Contact a qualified electrician. AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE...
Page 9
WARNING: Note the following warnings before use: The Source 4WRD LED is not user serviceable. Field • modification of the Source 4WRD LED will void your ETC warranty. Do not use the fixture below 5°C (41°F). • Minimum storage temperature is 5°C (41°F). When the •...
Take care to prevent contact between the LEDs and the reflector. For the 230 V (CE) Source 4WRD LED or Source 4WRD Color (CE), secure the earth bond wire to the Source 4WRD PAR or PARNel Fixture Body using the provided screw and washer. Threaded...
5. The Source 4WRD PAR or PARNel Fixture Body optics are optimized for PEAK focus. Turn the Z-adjustment knob toward PEAK until the knob becomes loose, and then tighten the Z-adjustment knob an additional quarter turn. This sets the LED light source into the appropriate position within the fixture.
The accessory holder is equipped with a spring-loaded retaining clip that prevents color frames and accessories from falling out. For best results, we recommend that you use the included diffusion on the Source 4WRD PAR or PARNel Fixture Body when paired with the Source 4WRD Color. WARNING: Make sure all color frame accessories are locked in position with the retaining clip before hanging the fixture.
About PAR Lenses The Source 4WRD PAR Fixture Body includes a flat lens, but the fixture can use the same lenses as the Source Four PAR. Lenses for the Source Four PAR come in five versions, and there are differences among four of the types depending on the date it was shipped.
Page 14
21° x 34° oblong beam shape • WFL (Wide Flood) Many facets • 7061A4073 Vertical axis (dashed line on image) is • between facets 30° x 51° oblong beam shape • Source 4WRD Installation and User Manual...
When not installed on a fixture, store the • Source 4WRD LED in its original packaging or in a dust-resistant plastic bag. Store the Source 4WRD PAR or PARNel fixture • at temperatures of 5°C (41°F) or higher. If you must store the fixture below 5°C (41°F), •...
Unplug the fixture and allow it to cool before you change a lens. AVERTISSEMENT : Débrancher le projecteur et le laisser refroidir avant de remplacer une lentille. Replace lenses if they become cracked or badly scratched. Source 4WRD Installation and User Manual...
Page 17
Spring clip behind the tabs on the bottom of the lens rotator ring. Gently push the top of the lens inward until it snaps behind the clip. Source 4WRD Installation and User Manual...
Page 18
6. When the lens drops, remove your finger, allowing the lens to slide forward until it rests on the lens catchers. See figure at right. Lens 7. Carefully remove the lens. catcher Source 4WRD Installation and User Manual...
Page 19
Bottom two 2. The bottom of the lens has a center notches cluster of four notches. Place the two center notches behind the tabs at the bottom of the lens rotator ring. Source 4WRD Installation and User Manual...
Page 20
Remove a PAR Lens on page 13 Remove a 1. Remove the lens. See PARNel Front Lens on page 14 2. To protect the Source 4WRD LED during cleaning, remove the LED housing by loosening the attachment screw and pulling the LED page 6 housing straight out. See image on 3.
Page 21
Source 4WRD Installation and User Manual...
Page 22
Source 4WRD Installation and User Manual...
Page 23
Source 4WRD Installation and User Manual...