Kramer VP-427X1 User Manual page 57

Function Description
DISPLAY? Get output HPD status.
ETH-PORT Set Ethernet port
protocol.
If the port number
you enter is already in
use, an error is
returned.
The port number must
be within the following
range: 0-(2^16-1).
ETH-PORT? Get Ethernet port
protocol.
FACTORY Reset device to factory
default configuration.
This command
deletes all user data
from the device. The
deletion can take some
time.
Your device may
require powering off
and powering on for the
changes to take effect.
HDCP-MOD Set HDCP mode.
Set HDCP working
mode on the device
input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink
- MIRROR OUTPUT.
When you define 3 as
the mode, the HDCP
status is defined
according to the
connected output in the
following priority: OUT
1, OUT 2. If the
connected display on
OUT 2 supports HDCP,
but OUT 1 does not,
then HDCP is defined
as not supported. If
OUT 1 is not
connected, then HDCP
is defined by OUT 2.
HDCP-MOD? Get HDCP mode.
Set HDCP working
mode on the device
input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink
- MIRROR OUTPUT.
HELP Get command list or
help for specific
command.
VP-427X1 – Protocol 3000
Syntax
COMMAND
#DISPLAY?out_index<CR>
FEEDBACK
~nn@DISPLAYout_index,status<CR><LF>
COMMAND
#ETH-PORTport_type,port_id<CR>
FEEDBACK
~nn@ETH-PORTport_type,port_id<CR><LF>
COMMAND
#ETH-PORT?port_type<CR>
FEEDBACK
~nn@ETH-PORTport_type,port_id<CR><LF>
COMMAND
#FACTORY<CR>
FEEDBACK
~nn@FACTORYok<CR><LF>
COMMAND
#HDCP-MODio_stage,io_index,mode<CR>
FEEDBACK
~nn@HDCP-MODio_stage,io io_index,mode<CR><LF>
COMMAND
#HDCP-MOD?io_stage,io_index<CR>
FEEDBACK
~nn@HDCP-MODiio_stage,io_index,mode<CR><LF>
COMMAND
#HELP<CR>
#HELPcmd_name<CR>
FEEDBACK
1. Multi-line:
~nn@Devicecmd_name,cmd_name...<CR><LF>
To get help for command use: HELP (COMMAND_NAME)<CR><LF>
~nn@HELPcmd_name:<CR><LF>
description<CR><LF>
USAGE:usage<CR><LF>
Kramer Electronics Ltd.
Parameters/Attributes
– 1
out_index
– HPD status according to
status
signal validation
0 – Signal or sink is not valid
1 – Signal or sink is valid
2 – Sink and EDID is valid
– TCP/UDP
port_type
– TCP/UDP port number
port_id
(0 – 65535)
port_type – TCP/UDP
0 – TCP
1 – UDP
– TCP / UDP port number
port_id
(0 – 65535)
io_mode,
0 – Input
1 – Output
–
io_index
For inputs:
1 – HDBT
2 – HDMI
For input: 1
mode – HDCP mode:
for inputs
0 – HDCP Off
1 – HDCP On
For output
2 – Follow Input
3 – Follow output (HDCP defined
according to the connected
output)
io_mode,
0 – Input
1 – Output
–
io_index
For inputs:
1 – HDBT
2 – HDMI
For input: 1
– HDCP mode:
mode
for inputs
0 – HDCP Off
1 – HDCP On
For output
2 – Follow Input
3 – Follow output (HDCP defined
according to the connected
output)
– Name of a specific
cmd_name
command
Example
Get the output HPD status of
the output:
#DISPLAY?1<CR>
Set the Ethernet port
protocol for TCP to port
12457:
#ETH-PORT0,12457<CR>
Get the Ethernet port
protocol for UDP:
#ETH-PORT?1<CR>
Reset the device to factory
default configuration:
#FACTORY<CR>
Set the input HDCP-MODE
of HDBT to Off:
#HDCP-MOD0,1,0<CR>
Get the input HDCP-MODE
of HDMI:
#HDCP-MOD?0,2<CR>
Get the command list:
#HELP<CR>
To get help for
AV-SW-TIMEOUT:
HELPav-sw-timeout<C
R>
55