Kramer VP-427X2 Quick Start Manual

Scan for full manual
Step 1: Check what's in the box
VP-427X2 4K HDBT/HDMI Receiver/Scaler
1 Power adapter and cord
Step 2: Get to know your VP-427X2
# Feature
1 ON LED
2 INPUT Select Button
3 INPUT HDBT 1
LEDs
HDBT 2
HDMI
If the selected source is not connected to an input, its LED flashes.
4 IR IN 3.5mm Mini Jack
5 IR OUT 3.5mm Mini Jack
6 MENU Button
7 ENTER Button
– Button
8
9 FREEZE/+ Button
10 Ethernet RJ-45 Connector
11 PROG USB Connector
12 INPUTS HDBT 1 RJ-45 Connector
13 HDBT 2 RJ-45 Connector
14 HDMI Connector
15 RS-232 CONTROL 3-pin Terminal Block
Connector
16 REMOTE Contact-Closure 4-pin
Terminal Block Connector
17 AUDIO 5-pin Terminal Block Connector
18 HDMI OUT Connector
19 12V DC Connector
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
VP-427X2 Quick Start
VP-427X2 Quick Start Guide
This guide helps you install and use your
Go to www.kramerav.com/downloads/VP-427X2
upgrades are available.
Function
Lights green when device is powered.
Press to select the input (HDBT 1, HDBT 2 or HDMI).
Lights green when the HDBT 1 input is selected.
Lights green when the HDBT 2 input is selected.
Lights green when the HDMI input is selected.
Connect to an IR sensor.
Use to control a remote device that is connected to the transmitter side. IR commands
are passed via HDBT tunneling only to the selected HDBT input (1 or 2).
Connect to an external IR emitter to control a local device from the transmitter side.
Press to enter/exit the on-screen display (OSD) menu. Press together with the –
button to reset the output to 1080p resolution.
In OSD, press to choose the highlighted menu item. Press together with the
FREEZE/+ button to reset the output to XGA resolution (1024x768).
In OSD, press to move back through menus or decrement parameter values. Press
together with the MENU button to reset the output to 1080p resolution.
In OSD, press to move forward through menus or increment parameter values. When
not in OSD, press to freeze the display.
Connect to a PC via a LAN to setup and monitor the
HDBT, as well as upgrade the firmware. (Configured via web pages).
Connect to a USB stick to perform firmware upgrades.
Connect to a transmitter (for example, the Kramer TP-789Txr).
Connect to a transmitter (for example, the Kramer TP-789Txr).
Connect to an HDMI source.
Connect to a serial controller or PC to control
connect to a device (e.g., a display) to control it via
Can be configured via the device web page.
Connect to contact closure switches, an occupancy sensor and/or toggle switches
(contact between the desired pin and GND pin), to turn display on or off. See
Operate
Connect to a balanced stereo audio acceptor.
Connect to an HDMI acceptor.
Connect to the supplied power adapter.
VP-427X2 for the first time.
to download the latest user manual and check if firmware
2 Bracket sets
4 Rubber feet
VP-427X2.
P/N: 2 9 0 0 - 3 0 1 4 6 4 QS
1 Quick start guide
VP-427X2
, tunnel data via
VP-427X2 (default configuration), or
VP-427X2
.
Rev: 2
Step 6: