Page 1
CLUB SERIES SHOULDER PRESS ASSEMBLY INSTRUCTIONS Part # 7142101 Revision:10/13/03 Rev A...
Page 2
PARTS LIST PART # DESCRIPTION PART # DESCRIPTION 71424xx TOWER 3102905 3/8 X 3-3/4” BOLT 7142201 CABLE 3102924 3/8 X 1-3/4” BOLT 6692601 3 X 2 END CAP 3202407 3/8 X 3-1/4” BUTTON HEAD BOLT 6714901 GUIDE ROD BUSHING 6965801 AXLE 3222801 4.5"...
Page 4
15 3/8 X 3-3/4” FIGURE 1 STEP 1: • LOOSELY assemble the CROSS SUPPORT (2) to the TOWER (1) and the BOOM ASSEMBLY (4) using eight RH CAPS (41), four 3/8 X 3-3/4” BOLTS (15), eight 3/8” SAE WASHERS (21), eight 3/8” RH WASHERS (22) and four 3/8” LOW HEIGHT LOCK NUTS (19) as shown in FIGURE 1.
Page 5
FIGURE 2 12 3/8 X 2-1/2” 13 3/8 X 2-3/4” 13 3/8 X 2-3/4” STEP 2: • LOOSELY assemble the CROSS BRACE (5) to the TOWER (1) and the BOOM ASSEMBLY (4) using seven RH CAPS (41), three 3/8 X 2-3/4” BOLTS (13), one 3/8 X 2-1/2” BOLT (12), seven 3/8” SAE WASHERS (21), seven 3/8” RH WASHERS (22) and three 3/8”...
Page 6
CABLE FIGURE 3 STEP 3: • Carefully route the CABLE around the pulleys as shown. Make sure the CABLE is in the grooves of all the pulleys. 17 3/8 X 3-1/4” BUTTON HEAD FIGURE 4 STEP 4: • Slide two ACCORIDIAN SLEEVES (39) over the shafts on the BOOM ASSEMBLY (4) as shown in FIGURE 4. •...
Page 7
TIGHTEN! 17 3/8 X 3-1/4” BUTTON HEAD FIGURE 5 STEP 5: • SECURELY assemble the PILLOW BLOCKS (23) to the SHOULDER ARM (9) using four previously inserted 3/8 X 3-1/4” BUTTON HEAD CAP SCREWS (17), four 3/8” SAE WASHERS (21), four RH WASHERS (22), four 3/8” LOW HEIGHT LOCK NUTS (19) and four RH CAPS (41) as shown in FIGURE 5 •...
Page 8
FIGURE 7 16 3/8 X 1-3/4” STEP 7: • SECURELY assemble the PULLEY BRACKET (3) to the SHOULDER ARM (9) using one 3/8 X 1-3/4” BOLT (16), two 3/8” SAE WASHERS (21), two RH WASHERS (22), one AXLE (18), one 3/8” LOW HEIGHT LOCK NUTS (19) and two RH CAPS (41) as shown in FIGURE 7...
Page 9
FIGURE 8 3/8 X 3-1/4” 32 STEP 8: • SECURELY assemble the two PULLEY BRACKETS (3) and one 4-1/2” PULLEY (29) to the bracket on the BOOM ASSEMBLY (4) using one 3/8 X 3-1/4” BOLT (32), two 3/8” SAE WASHERS (21), two RH WASHERS (22), two AXLES (18), one 3/8” LOW HEIGHT LOCK NUT (19) and two RH CAPS (41) as shown in FIGURE 8.
Page 10
CABLE DIAGRAM CABLE 3/8 X 1-3/4” 16 FIGURE 9 STEP 9: • Carefully route the CABLE around the pulley as shown. Make sure the CABLE is in the grooves of all the pulley. • Assemble the swivel end of the CABLE to the SHOULDER ARM (9) using one 3/8 X 1-3/4” BOLTS (16), two 3/8” SAE WASHERS (21), two RH WASHERS (22), one 3/8”...
Page 11
3/8 X 3” 14 FIGURE 10 STEP 10: • SECURELY assemble the BACK PAD (35) to the BOOM ASSEMBLY (4) using two RH CAPS (41), two 3/8 X 3” BOLTS (14) and two 3/8” RH WASHERS (22) as shown in FIGURE 10.
Page 12
3/8 X 1-1/4” 11 FIGURE 11 STEP 11: • SECURELY assemble the SEAT PAD (36) to the BOOM ASSEMBLY (4) using two BLACK RH CAPS (26), two 3/8 X 1-1/4” BOLTS (11) and two 3/8” RH WASHERS (22) as shown in FIGURE 11.
Page 13
FIGURE 12 HEAVY WEIGHT OPTION STEP 12: • Insert the two GUIDE RODS (10) (found in the SHROUD KIT box) into the base of the TOWER (1) as shown in FIGURE 12. Lubricate the GUIDE RODS (10) with a slicon or teflon spray that is available at most hardware stores. •...
Page 14
FIGURE 13 12 3/8 X 2-1/2” TIGHTEN! STEP 13: • SECURELY assemble the GUIDE ROD SUPPORT (8) to the TOWER (1) using four RH CAPS (41), two 3/8 X 2-1/2” BOLTS (12), four 3/8” RH WASHERS (22) and two 3/8” LOW HEIGHT LOCK NUTS (19) as shown in FIGURE 13. •...
Page 15
FIGURE 14 STEP 14: • The WEIGHT STACK LABEL sheet (37) includes labels for both lbs. and kgs. for both the standard and optional weight stacks. • Peel the backing off the WEIGHT STACK LABELS (37), line up sheet to the right of the selector openning and apply labels to the 10 LB.WEIGHT PLATES (33) and/or 15 LB.
Page 16
FIGURE 15 3/8 X 2-1/2” 12 STEP 15: • SECURELY assemble two COUNTERBALANCES (7) to the SHOULDER ARM (9) using four RH CAPS (41), two 3/8 X 2-1/2” BOLT (12), four 3/8” SAE WASHERS (21), four 3/8” RH WASHERS (22) and two 3/8” LOW HEIGHT LOCK NUT (19) as shown in FIGURE 15.
Page 17
FIGURE 16 STEP 16: • Assemble the PLACARD LABEL (30) or the FOREIGN LANGUAGE PLACARD LABEL (31) to the FRONT SHROUD as shown in FIGURE 16.
• Upholstery with mild soap and water. • Guide rods with a cotton cloth. • Hand grips with mild soap and water. • Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800) 351-3737. Inspect: •...