Table of Contents
Advertisement
3-25
b. 6237, 6267
1. Remove deer trim pad, heater dact, and both
kwding hole covers.
2. Retuteve door window glass.
Sec Note SIb.
CAUTION:
On bedies eqaipped with electri
cally powered windo'v regulators. IX NOr OPER
ATE
REOUI .oi't:tut
MOTOR after the wittdow
assctnbty
a disengaged [rent the regulator, or
as a Ixncln eperstban alter the regulator Is re
moved from the doer. Operation of the motor,
with
the Iced retitoved. tnnay damage the ttnit and
tnnake it inoperative.
3. On Louis eqttipped witlu electrically pewered
window regulators, dIsconnect tnnotar leads iitdima-
ted in FIg. 39.
1. On closed cotupes, rctnovc the ventilator divi
sion cbanttel lowet adjust i,, studnat
'B''. Fig. 3-34.
5. Remove two scrawe secaring stationary can
to door ittner panel and remove cant, i-ia. 3-39.
reunnoved without looking
he sector in poai-
2. Drill 1/4'' hole thru:uugh backpi'ate aitd eecter
wcln]tt area iundicated itt Fig. S-'lc'. depending on
position of lift arm,
<OTS;
Do
,'.nt
dtt' It
ioto
motar
ltouai!tg,
pttrt or whiclt is indicated ho the darted lines.
In tadditlout, bate hale not less than 3/4'' away
lrotn edge of backplate or sector.
6, Remove regulator cam from rcgutlator.
7. ltetnnawe regulator te door inner panel at-
ta chitng oc rewa
-
I,,
8. Carefully wotk regulater assembly with at-
taclted titoter tlnroogh larger loading hole attd me-
move irtttnn alir.
NOTE:
The
lnatracticns for. retnneving
he
tnnatctr irma rIte regulatar assctutbly are eutlitied
in Note 36.
9. 'Ut, install, reverse removal procedure. Seal
deer ioeer pane! as spec iiicd un Note 15.
36
Window Regulator Electric
Motor Assembly Removal and
In sta II t ion
1. Remove el'c tric windv
regulatar assembly
front deer sad clamnp secutrely in vise.
NOTE:
The pesitien of the regulator clamped
in the visa will vary with One type of regulator
and position of the lift arm.
c.AL:'r!ON:
Ilk' 5t:103 TO PERFORM STEPS
2
and 3
REPOR ,Ut"IEMrINC; 'It REMOVE
THE
MOTOR 'SS'EMBLY PROM TOld RhOti-
LTOR. 'late regu]ator lift arm, which is under
tension
from the counter-balance spring can
cause sertwas Injamy,
if rha motar as'sennbey
3. lttecrt t/4'' bolt through holes lit baci-plate
and sector at,,1 itt stall ncr to belt.
4
Re t,,eva the In rae 3 a ttac hittg N, Its Fig. I 4ft
-
a:,
d te tttev , n ,Ietot s sac tn'nly item tegu latot
NCr u-h:
Paean steel chips
off the regulator
secter :ut:,a motor pi t',iutn geat.
S. To install, reverec: reotLtval praredure.
NOTE:
Be .sttttn to remove oat and bolt befote
reinstalling regulator
37
Door Glass Run Channel
Removal and Installation
a. 6219, 605
NOTI':
T::e glass ttutt chonoels are secured
to
the deer with resebud clips. Fig, 1-41. which'
are snapped into holes In the window frame.
in addition, the lower ends ci the cltamtele which
extend slang the look pillar arc secured by a
utut installed to a stad .Soppert. The lower end
of the channel wluich exteitda alettg Isa rear
dr
hinge pIllar is secured with a screw,
The channel assembly en the frent deer con
sists of two sections: an upper, which exte,nds aleeg
the door header, and a lower, which exteod slang
tlte door lock pillar.
BODY
Fig. 3-40
t,ec,;ic Window Regolotar
is
ti Ltn
The clnanoel asscr'thly on titi', rear door consists
Advertisement
Chapters
Table of Contents
