Starter Motor; Assembly And Installation Of Starter Motor - Cadillac 54-6219 1954 Shop Manual

11-24
ENGINE ELECTRICAL
C. Ro'nove tour switch arracci og
ecrcwe and
take off solenoid awrchl
2.
Remove three bolts and remove coiltiliutator
end frame and field frame acsrnll,lY Fig, ti-SO.
3.
Romnove large retainer clip, rhon ur,hook shift
lever spring and remove.
4.
Remove ems II retofaer clip and remove upper
shift Lover a Fiaft
-
5. Roolove armmlaruru with clutch and lower shift
lever from housing. Also remove Thrust collar.
6.
Remove clutch from armature byfirsr sltding
thrust collar off end of armature shaft, Fig. Ii -3i
7.
Slide a standard 1
r'
pipe
coupling or other
metal cylimider of sulrcb_u
size on:o shaft, Cu
end
of coupling or cvbndar burrs agai1,s reclec or re-
tadi ci:,
Fig, l1-32.Tapendofce uling
thhomu:.:cr,
drietas retainer towards armature and on-snap ring.
S.
Roiltove snap ring from groove in shsfr, using
pliers or uther suitablo taoi. liopace
atlep ring
if
distorted.
9.
Slide retainer amid clutch from armature
shaft.
IfI. Disassemble brush holders from field frame
a. Remove screws aitachang leabi-. and brushes
to the l'.o;dor.s.
h, Byhp.nd, p-oss do-a-n on rile flat spring so feat
cemiter of spring c-ears tIte reiaiiiemlg slaT, Slide
tiff the hm-u,so spring ann two brush holdem-s as a
grnaP,
c. Repeat procedure for remaining set of brtlsh
holders.
41 Assembly and Installation of
Starter Motor
Thu assembly and installation of thu stsrtcr
motor is b-to reverse of the prouedurc- doscrihed
she cc, w irli LI te cacepI ion of tl:e foLio wi up p roce
-
du r e foe rep lacing CItI tch cc
a rmna 1:: re
sh a
a. Lubricate drive end 0f armature shaft with
grade Idoll.
b. Sl:do c..titch ss:La:' Olitu
armllalllrc
shaft
!ill
pa:L1c'lm
ouTward,
c. SiidC:
reTtin0r olito
sh:afl',rt Ii ca?ued surface
gond of shaft.
Spiral Splinea
S!lap R-n9
WI
/
/
Rtoioa
Thram] Codar
rig.
Il-SI Slauc, Ammaiuti Aitmbly
-
d, Stand arroa:h:,-ct
DII cite
of wood -surface with
comsmiulalcr down Position snap rimlg on upper end
of sitaf: 511:1 ho,cl
ill P.5Cc wirl-
a Itiock of wood.
Hit wood olock a blow with hamuojer,
foreilIp aoap
ring over end of sJ:aft, Sicle snap ring down into
groove by hand, Fig. 11-53.
e. Assemhee thrust coilor on .shmufT wcrllsllouLdor
'mcxc to
.ItiaO
rimig,
l'Laee itrelature on 'to rb bench and pesition
retainer and thrust collar
next to .snap ring.
Then
ust
'I tWO pair
of p!ic-rs at an me nob lane pair on
Oerri,nti tg
CIa I: I 1
._-'Piee Coupling
..-Armclar@
11-22
Obvin9 Reio;,mr OfF ioop Ring